วีดีโอ

you will love it-and Titan's service is excellent

Superior Tool 3845 Sink Drain Wrench-amzn.to/44Np1Dg

works very well

wonder if you have a problem with a fork in the tranny? this video shows me removing the top of the tranny to 'unstick' the forks/shifter buttonth-cam.com/video/LfeVdQRWtfA/w-d-xo.html . Maybe if you pull the top off and check it out you can fix it? I drove mine for a year after it locked up in 2nd gear (but forward tranny)-I repaired it by welding the shifter button and grounding it down to factory specs. Of course it sounds like its running now, so proceed with caution

the same reason you use a razor blade to remove sticky labels/paint from windows-thanks for watching

@@haparoundthehouse6618 But your chances of scuffing it are much higher and once you scuff it, it’s always going to be a sticky spot for build up. There are videos on how to clean these things properly without having to use a blade.

@@bobomonkey702 fair enough-but using a blade properly makes it almost impossible to "scuff" the glass

@@haparoundthehouse6618 Ok, I understand your point not trying to argue with you at all. I’m just trying to let you know there are easy ways to take that off that much quicker than using a blade and probably safer than recommending a blade for others. Have good day. ✌️

@@bobomonkey702 fair enough

dont really know-keep an eye on it as you don't want to 'cook' it you want to dry it

looked at the angle of the cement pad and decided to put the holes near the largest defect-keeping in mind the closeness of the edge as the foam will blow out-in other words i guessed

@@haparoundthehouse6618thank you!

i had good luck with it- thanks for watching

works great thanks for watching

take an afternoon and a whole bunch of spray foam cans and give it a shot-thanks for watching

give-your funny

​@@haparoundthehouse6618 I have a black and decker medium size food processor the container cracked I contacted them via Facebook I attached a pic i asked for a replacement container, they sent me a new food processor, no charge

I don't remember an adj in the clutch-does the pedal feel 'normal"? I have a 'bad trans' right now, in fact the tranny from the video is now bad enough to remove the shifter weld up the "button" and grind it down to original specs. As you use the shifter it wears and with enough wear it will indeed get stuck in neutral. THis is were I'm at and sounds like where you are at as well. www.stractors.com/t92-transmissions/ this is a brief summary of how to repair the shifter. I already repaired a spare transmission shift linkage and will repair the trans from the video after the mowing season. The repair isn't too difficult if you are handy-good luck, my guess is you have a worn shifter button- you more than likely could try removing the top of the tranny and smacking it around-more than likely could give you some more run time until it locks up again

the trans do leak-l'll have to try that. Thanks for the info-

as long as the line has a portion straight enough to go into the clam shell-I haven't tried that, but if it were my car I would definitely give it a shot

@@haparoundthehouse6618 thanks, friend👍👍

rubbery and epoxy won't stick to it

yes-the material used by the manufacture was cheap and not well suited for the rifle-thanks for watching

Im almost certain you would have to have some sort of backing to ensure the epoxy doesn't just fall through the hole. I'd use dry wall mesh or if you cant get to the back side I would use a silicone caulk to fill the hole then remove enough caulk to get a decent amount of epoxy. I would give it a try---

shot a video-th-cam.com/video/sm-9XOUyUzc/w-d-xo.html

The idea was to demo a normal tire in these conditions-thanks for watching

@@haparoundthehouse6618 oh, ok. Thank you for video. I love this car 🙂

@@krzysztofopalinski-bs5of they seem to be well built-get decent gas mileage

i hear ya

Please don’t take my prior comment the wrong way. We have a patio table made of pvc fittings for legs and a fiberglass table top. We purchased it in 1994. It’s amazing how it’s held up with the exception of some small chips on the top. Anyway my wife purchased the kit based on your video today, I applied it, waited an hour, sanded it. It looks amazing. Again thank you and god bless you.

@@RichieRichRangers no worries-thank you for watching

nice

I had good luck with SS-hope it turns out good

sounds like there is very strict quality control at the factory-thanks for watching

Glad you enjoyed it

Glad you could use it-

Glad you enjoyed it

thank you for watching

thanks for watching

thanks for watching

Didn't have to replace the sink-came out nice. Thanks for watching

I don't understand the question

@@haparoundthehouse6618 I mean, for the TSB, how do we install it? Is it a software update or a physical repair done at the dealership? If so, do we download the PDF and then what? I am just trying to understand the procedure of instillation.

@@KINGMUFASA A TSB is just a piece of paper uploaded to a digital document (PDF)- its just info, in my case it informed me that toyota didn't program the computer correctly and didn't recall the car and was forced to put out this info as toyota service bays couldn't fix it . there maybe TSB that will allow the average home mechanic to fix their car (like change/adjust a defective part)-in my case I would still have to have toyota reprogram and no this can't be done at home-you got to pay toyota

@@haparoundthehouse6618 Ohh, I see. Thanks so much. 👌

without seeing the crack its hard to say-

Welcome

true

Sounds like a restriction in the drain pipe-Or and much more unlikely is a partial main vent blockage. are any other drains that are acting up? I would suggest snaking the pipe. Have you tried blistering hot water down the pipe (in case its hardened grease?)

@@haparoundthehouse6618 No other drains in the house acting like that. I used a quality drain cleaner today and let it sit for a hour then boiled some hot water to flush it out. It helped maybe try again tomorrow. I just can't see how a clog in the trap can cause water to flow out of that air valve.

@@billy2bob63 My bet is there is a blockage after the trap. I would pick up a snake long enough to get into the 4" pipe. Do you have cast iron or PVC?

@haparoundthehouse6618 PVC in a 25 year old mobile home that I purchased new.

@@billy2bob63 I'd snake it-

great tool especially if there is no room for larger tools

true

nice-

not really much of a pitch-i dont use much soap and very little grease goes down the sink-i also make sure to rinse the sink with very hot water often, this can cut the gunk inside the tubing

thanks for watching

true

weighed at the gravel pit

usually the nozzle screws right off-

l eat a higher fat diet than most-l do not trim the fat. thanks for watching

glad it worked out-thanks for watching