วีดีโอ

It said that irRicever was not declared in this scope

are you not going to show movement?

I have this error (it doesn't matter if I use python or python3): pi@raspberrypi:~/Project/bmp180-python $ python3 ./BMP180test.py Traceback (most recent call last): File "/home/pi/Project/bmp180-python/./BMP180test.py", line 25, in <module> temp = bmp.read_temperature() ^^^^^^^^^^^^^^^^^^^^^^ File "/home/pi/Project/bmp180-python/BMP180.py", line 99, in read_temperature UT = self.read_raw_temp() ^^^^^^^^^^^^^^^^^^^^ File "/home/pi/Project/bmp180-python/BMP180.py", line 75, in read_raw_temp MSB = self._read_byte(BMP180_TEMPDATA) ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ File "/home/pi/Project/bmp180-python/BMP180.py", line 42, in _read_byte return self._bus.read_byte_data(self._address,cmd) ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ OSError: [Errno 5] Input/output error

ขออบคุณมากครับกับสาระดี

What about the new bored

sorry but what is this title? just numbers doesnt make sence. ur not goin to g et a lot of clicks/views with ths title. although this vid was on my for you page so there is that.

To the viewers of this video that are stuck on the sample code downloading part, I had the same issue, and I resolved it by clicking more on the box under the video, scrolling down, and when you see 3 different-colored books with a belt or something like that connecting them, click it and then, I think you will figure it out once you get past it, but there might be an error message.

Is this a new one not featured yet?

Just got mine for Christmas

i cant download the code please help

mine is not moving

I can’t change the code lines to my wifi info. How can I fix this.

hi do you have tutorials to use the microbit older version (not 2.0) with the sensor? I can´t enter into the website wehre you posted all the tutorials I would really appreciate if I can enter Thanks a lot

On the servo motor SG90 product details, it says you recommend using pin 9 or 10 for the orange control wire. And I see you move the black wire from the ENA pin of the Model X from from pin 9 of the Wi-Fi shield to pin 3. Is there something special about pins 9 and 10? I figured Digital PWM Pins 0-13 would be identical. Is that not so?

Hi Osoyoo.I like your cars and lessons with Arduino IDE.Please answer me I have a problem with this lesson because I cannot correct the mistake in the first type.Can you please answer me how to correct it,otherwise I would not be able to complete the lessson 6 and I would be in trouble.Waiting for your respond.

The music is really irritating. Can we turn the music off inn the videos??

Can app be on Samsung

how do i get smartcar-lesson1.mo file?

Hallo , wo man findet Folder Smartcar lessen 1 Thanks

Are the wheels some parts injection molded or metalic?

It’s not the first thing that comes out to you and your friends

これはブラシレスですか？

can i have a code for this lesson ? the zip file you included i its erased

what should i do I always get this kind of error Arduino: 1.8.18 (Windows 10), Board: "Arduino Uno" Sketch uses 7692 bytes (23%) of program storage space. Maximum is 32256 bytes. Global variables use 489 bytes (23%) of dynamic memory, leaving 1559 bytes for local variables. Maximum is 2048 bytes. An error occurred while uploading the sketch avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0xe8 avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0xe8 avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0xe8 avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0xe8 avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0xe8 avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0xe8 avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0xe8 avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0xe8 avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0xe8 avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0xe8 This report would have more information with "Show verbose output during compilation" option enabled in File -> Preferences.

had some issues but figured them out by looking at the website 👍

Hey there! Why isn't my robot car turning right or left its line-tracking path correctly, and how can I fix this? When I test it like in the minute 2:15 to 2:22 it doesn't turn.

I love ur vids

5 walt but how many amperes will it be?

Wow can u post the code?

cum

it is super frustrating to get the bot to work from a MAC

my car wont go after the black line and sensors are added and ajusted? Is there anything else ?

Promo_SM 🤤

i got "exit status 1 Compilation error: exit status 1"

Well this was random haven’t done robotics in over a year

Why isn't my robot car following its line-tracking path correctly, and how can I fix this?

the M2.2*8 self tapping screw is to small to fix MG90S servo motor (orange ) on black servo horn . what should I do ?

Where did you put the battery? Its not shown in any of the tutorials.

I cant put the osoyoo uart wifi shield on the osoyoo board and cable !?!?!? The metal line doesn’t go in the black squares !? What to do please answer asap

i have everything correct but the light on the h bridge isn't turning on

what kind of batterys does it need?

thank u

How can I email you?

When I try to do this the software constantly says, "Compilation error: IRremote.h: No such file or directory" what should I do?

This code doesn't work.

Hello, when I putting the command "sudo pip3 install adafruit-pca9685" The terminal say: "error: externally-managed-environmet". I need help please

Yo wtf the 2.0 y bored is way to big

15:03

Hello, the code is the same as the video or did you change it?

good