วีดีโอ

Do u sell any by anychance

Cool looking car you created there!---enjoy!

Any good on a 70cc moped (upgraded from a 50cc) ? Thanks

How to set up float height?

Do a 49cc mid size pocket bike have a cdi pull start

Great video. Enbig hole about the internal diameter of a 1/2" copper tube. Not bigger so you'll loose fuel atomization.

you just learned me more about carburators then my dad, school edjucation and some of my friend all together just below 15 minutes well done!

I drilled every hole I found in that carburetor just to fit it on a 72 cc Zuma and it works great like if it’s a fucking 22 mm carburetor

Jesus christ, the autozone accessory isle puked all over that poor car.

thats a nice vid... id go for a bigger carb from a proper manufacturer....

you got the link for the spoiler?

You have a link for your exhaust that you put in?

It’s a one wheel drive car 😂😂😂

And wat notch did u set ur needle pin at...?

Hey ..great video I want to try this on my nt carb ..please give more detail on how u put wire in .how deep etc...and how do u secure it so it stays put ..any more guidance or instructions wud be greatly appreciatedi want to try this before I waste money on a jet kit

gj man i have 2019 se winter version looking at ideas

Can u help m8..I bought Japanese 49cc néw added fuel lifted choke to top started up ran for min then went to lower choke and starts revving by itself

cool

You are genius sir... I use Subaru robin NB411 carb. It's the same problem. The oil to rich. So i try your method and problem solved. Even the sound is lighter and smooth. thank you very much sir.👍👍👍

This video was helpful - I just took mine apart and cleaned it and realize there is no idle circuit and it went through the single main jet. It runs well when the throttle is open and dies quickly when the needle closes which is consistent with what you described. Was just going to raise the needle one clip so it doesn't go in as far and figured that would help. Is your wire then just leaning out the jet or is it also intended to limit how far the needle goes down? If I am happy with the tune, I assume the needle being raised is sufficient, will try that next when my son is home since it is his learning project.

Do these motors have a pilot jet and also what is the brand of the named japanese carb? Thanks

Super helpful mate!

Love the versatility! Bravo

Tq.

good job bro, i subscribed

Why not just use silicone one time and you'll be done with it did you try that yet or no?

My last buy was the anbull "100" cc out the box with a 1 inch by 1 in hole in filter case is only pulling at 37 so far I couldn't keep it open cuz in turning traffic was coming in and thats on a 44 tooth sprocket. I know if I go lower tooth it will pick up more top speed but I like to pick up quickly

That's crazy how is that 49 cc going that quick the" 80" cc bike kits out the box are only hitting 25 30

you can solder up the jet and redrill to size for fine tuning, good because you can always reverse it with some heat and more solder

This had to be the stupidest clip I seen on engine bikes.its like all this dude wanted to do is let people know what his lil privatel Community has 😆

What where the symtomps of your engine running too rich.. I have the same caburator on my sons miniquad and I think I will follow your advise.. wonderfull video .. Im wating for your next video on the subjet👌🙌

My girlfriend bike sounds like it's gonna blow up 😂 I think this is the problem

Just had to tear apart and clean a carb just like this. Has been running for 2 days, and started to show signs of no fuel to the motor. The gasket inside the shut off valve was in pieces and the carb was full of gasket debris. You would think that they where using gaskets/orings that can handle fuel but clearly not, LOL.

great video, this is the definition of covid project😂

That is soooo quiet.. I liked it.. Such an awesome muffler.. So much better than the stock one..

Loved It!