วีดีโอ

Thanks for posting useful information.

Audio is poor too much background noise!

great video, thanks!

Many thanks for uploading these very interesting seminars. Love the 7UT86 tranformer protection series.

Thank you for sharing ❤

Thanks អរគុណ❤

Thank you very much 🙏🏿 u

thank you for uploading this series, very informative and helpful. very few resources can explain protection so clearly and deeply.

This video is helpful for someone to learn the electrical system, thank you for sharing.

More of reestablishing and rejuvenating the existing knowledge...altho all A's in electrical electronics signal processing just name with 3.72 magna cum laude. only B's in american history, literature, bla bla bla just keen on calculating not on reading and memorizing

thanks for sharing. very useful indeed for a 61 years old electrical engineer(MEMPHIS, TN38152)+Mathematician(MEM)+digital system engineer(Brunel,UK)+technologist. best regards from me RA from Putrajaya, MALAYSIA. will listen and re-listen for one-half hour in entirety.

no understand

What is Linkage Ratio?

I can't find the function Elec. fault start and Non- Elec. fault start in the Editor information Routing. Can you help me?

I can't find the function Elec. fault start and Non- Elec. fault start in the Editor information Routing. Can you help me?

1:37 to 5:28 Oil temp indicator

Thanks for sharing the fundamentals of 87L. This will surely prove valuable as the principles you have discussed answered many of my questions which was not addressed in many other discussions concerning line differential protection function. Thanks a lot.

Very useful to me, Thank you Mr. Ali Husain

The english language is very obstructive for the instructor. The instructor with native english language should have been better

Nice .. informative 👍

please, where can i get the pdf?

love it

love it

With the thumper hooked up to cable at one end, the fault reads 945 ft. Is that location from the thumper end, which is hooked up OR from the open end. Please and thank you!

Thank you 🙏

Hello, I want more information for Sage 230KV

Thanks!

very good thanks

Voice is poor

At 1:01:37 Abel was just checking if Norman has been paying attention to the story 😉. Great presentation, very relevant choice of questions and everyone on the discussion board - were true experts in the Art and Science of Protective Relaying! This video is among the most underrated on TH-cam. Everyone who was and who will be watching it - please give your thumbs up 👍🏽 and share it with your colleagues and apprentices. Thank you again for producing and sharing!

İnformative

Thank a lot, i gain a lot from this film

Hi, michael, can we use differential line relay with different brand? For example for local we use Siemens and remote we use ABB. Thank.

Good information and presentation

You mention within the contents of this webinar, about the slides being available.....Where would that be? Or could I request that you forward the slides from this presentation to my email.....Is this possible? Thanks, John

Exceptional

Hello can I get the Pricing of these products.

Great surge explanation 😊

yes

Excellent, Thank you for clarifying doubts

Excellent introduction of the protocol.

This is beautiful ❤️

Thanks 🙏

would like to get your contact number

Thanks alot

I wonder, can you have form of segregation 2b and 3b in the same enclosure? or shall I have 2b and 3b separated enclosure ? Thanks

Thanks Sir 👍

Relay location blocks out ZS0 and I0 40:00 40:04 L-G fault = 3ph fault for this fault location 50:03

Most of the wiring insulation says max volt rating is 600 volts . I wonder if supplying high voltage damages the insulation . can you explain why the insulation is not being damaged by the high voltage ??? what kind of test can be performed to find out why a rewound motor is pulling high amps ??? there is no voltage imbalance. motor and cables megged good.

Hi is there any incoming webinar regarding GIS ?