วีดีโอ

455 Big Block Oldsmobile, Fast EFI system, comp hydraulic camshaft, Edelbrock RPM manifold, 9/1 compression. Nice part about this engine build is peak torque of 525 LbFt @ 3800! A real stump puller! Built by JMacPerformance.com

A solid street engine with a "TON" of torque at a low RPM. Built by JMacPerformance.com

9/1 compression, stock but blueprinted bottom end. Edelbrock RPM cylinder heads, Crane full roller rocker arms, Comp Cams flat tappet camshaft, HEI distributor, Holley 650 vacuum secondary carb. 400 horsepower - 425 LBFT torque. Built by JMacPerformance.com

9/1 compression, world product 200 cc steel heads, Edelbrock RPM manifold, 650 Demon carb, SCAT cast steel bottom end kit, small comp cams hydraulic flat tappet camshaft, comp roller tip rocker arms, HEI distributor. good horsepower and "ALOT" of torque. 350 HP - 475 LBFT. A great 4 X 4 truck engine. Built by JMacPerformance.com

4 bolt main 396 Big Block Chevy, Stock forged bottom end with SRP pistons 9.5/1 compression, Stock but pocket ported cylinder heads with upgraded steel valve. Comp Cams hydraulic roller camshaft, Harland sharp full roller rocker arms, Quick fuel 750 DP carb. I was built for a 66 Chevelle with a 4 speed. Built by JMacPerformance.com

10/1 compression, FAST EFI system, AFR 185 cc heads, Harland sharp full roller rocker arms, custom Comp Cams hydraulic roller camshaft, SCAT forged stroker bottom end kit with SRP pistons, MSD stan alone distributor ignition system. Edelbrock RPM Performer intake manifold. Built by JMacPerformance.com

This engine was originally built with 11/1 compression and a .625 lift camshaft. It made great power but wasn't the best for a weekend cruiser. So to get more drivability I cut the compression to 10/1 and knocked about 20 degrees of duration and .035 lift from the camshaft. It only lost about 35 horsepower but gained a "TON" of drivability. RE-built by JMacPerfromacne.com

The customer was looking for about 500 Horsepower this combination over delivered by 60 Horsepower! 10.5/1 compression, 220 cc "Airwolf" cylinder heads by Dr.J's) Custom spec's hydraulic roller camshaft from Isky, Harland sharp full roller rockers, SCAT forged bottom end kit with SRP pistons. Single plane intake manifold from Dr. J's. ,MSD HEI distributor, 750 Mighty demon carb. Built by JMacPe...

All Aluminum 548 Big Block Chevy with N/A 1000 horsepower. Armen Maghdessian let us break in his engine on the dyno. It goes in he's 4 sec (1/8 mile) drag radial 57 Chevy. It's set up for a 600 shot of nitrous but he didn't have it set up in time to test it on the dyno. Dyno tested by JMacPerfromance.com

Stock 350 with some performance upgrades. Edelbrock RPM Performer intake manifold, 650 cfm Edelbrock carb., stock but balanced and blueprinted bottom end (Resized connecting rods, upgraded to ARP rod bolts, Moly piston rings, 462 casting cylinder heads steel valves, pump gas friendly harden seats, pocket ported, bronze valve guides, machined for bolt in studs and pushrod guides. 9/1 compression...

9.5/1 compression, SCAT cast steel bottom end with Keith Black Hypereutectic pistons, Howards cams flat tappet camshaft, World Products 200 cc cylinder heads, roller tip rocker arms, Edelbrock 750 cfm carb. HEI distributor. Built by JMacPerformance.com

10/1 compression with JE pistons, Brodix 270 cc oval port heads, custom comp cams hydraulic roll camshaft, Edelbrock air gap intake manifold, Pro systems custom built 950 cfm carb. SCAT cast steel bottom end, Harland Sharp full roller rocker arms. I purposely built it with the small heads to increase the torque at a lower RPM for better street driving. Built by JMacPerformance.com

I dyno tested a 555 Big Block Chevy with some of Mike Thermos (Co-founder of NOS) nitrous nozzles. There was an additional 100 horsepower just with a nozzle upgrade. Dyno tested by JMacPerformance.com

When the customer brought in his 351 Cleveland is was making less than 1 horsepower per cubic inch. I reworked the 4V cylinder heads, blue printed the bottom end, and installing a custom camshaft from Comp Cams. After the upgrades It was an improvement of over 100 horsepower. 450 horsepower - 475 LBFT. Built by JMacPerformance.com

JMacPerformance 450 horsepower Ford 351 Cleveland with a mean Idle!

JMacPerformance 69 Chevelle Irwindale 1/8 mile drag strip

JMacPerformance 69 Chevelle Irwindale drag strip 1st hit off the trailer