วีดีโอ

You need a disc plow or bush n bog harrow. Then you can use that disc harrow to cut it up and feather it out.

another 400 lbs on the disc would be nice,,,thanks

Dont drop your phone

I dont see reed canary grass

But you gotta add rocks big'ons and bigger'on to this issue

The disc weren't in the deepest cutting angle. It still had another notch to go.

You showed me exactly what i needed to see. Thanks for this video

I know this is 4 years old, but I would have stopped after 2 min and added weight, don’t look like your doing much, could get same effect dragging a handful of chickens backwards

🙂 I did not catch about your top link while disking, is it in float mode. To lay the discs on the ground in the front and back more evenly togeather ?

Hello, you are wasting time and fuel and a far fair comparison. Add 1000 to 2000 lbs on top of your disc and try again I think you will be happy. You are bouncing over everything because your disc weighs nothing. Add the weight and try again. Listen to your tractor and it will tell you if you have too much weight on it. The axle shaft on the disc should be crushing the dirt clods. Two passes will tell you how well you are doing and your total time will be reduced by 60-75%. You can always take the weight off.

Chiesel plow, than disc harrow imo

To make this work better. Let the top link loose. The top link lifts the harrow up, when the tractor goes in a hole..let the harrow drag on the floor

Great video Rob

For very smooth, delicate maneuvers for accuracy and safety: Using the toe of your boot under the front part of the treadle works very well.

5 years ago... I'm wondering what happened to the roots. Did everything rot down after it was cut? What else did you have to do after this?

Need to add some weight.

im assuming you have the guard on the fuel filter ?!

Well, how about that, another Floridian running a tractor over a tree farm. You're about the only one I've seen with land similar to mine. Thanks for the video. I, too, have a (recently purchased) planted pine tree farm in NE Florida. As I'm sure you are aware, the land undulates (highs and lows) where the trees were planted. Mine looks like what you show at 24:49 with underbrush like you show at 25:59. I have been racking my brain with how to level it out. I have tried a rotary cutter, rotary tiller, box blade with root rake, teeth on a grapple. Nothing levels it out. I know you said you use the harrow to cut through the roughage and stumps, but does it actually level out the highs and lows and make it flat? Thanks.

How much did you pay for the bush hog?

Best pedal design ever after the earlier version. Anyone who can not use it has no business on anything more than a lowes deere.

Impressive!

wonder if that tractor can handle a front end wood/brush grinder attachment, like a flail mower? Wonder if they can be front end pto driven?

Do you ever feel like the 5ft is too much for the L2501? I have a B2601 and have been told multiple times that a 5ft is too much for it and to go with a 4ft. But seeing as the b2601 actually has almost 1hp more at the pto, and over a hundred pounds more capacity on the 3pt, I'm left pretty confused on where that line is drawn🤔

Just bought a L2501, looks like its handling that disk just fine.....

THE WAY U ARE BRUSHHOG U JUST MIGHT TURN OVER

KEEP YOUR LOADER BUCKET DOWN BETWEEN 24 " TO GROUND LEVEL

IF U HAVE GEAR DRIVE TRANMISSON U WOULD HAVE ALOT MORE POWER / THAN THAT WHINE H S TRANMISSON !

OVER ALL U REALLY NEED FORESTRY KUBOTA 95 OR 97 SERIES " DRUM " MULCHER ! .

I BET U ALLREADY HAVE DEER ON YOUR LANDS ALL BRUSH U HAVE NOW

Nice - I’ve been clearing same stuff with a 5660suhd and landpride cutter. It’s also working great / more relaxing than golf!

How is your RCR2060 holding up long term? Any updates? Good video - thanks!

Thanks for the video. We have a similar situation - we recently had some acres and trails cleared with a forestry mulcher snd it left behind some serious sticks and small log chunks. Next step, I need to get the areas cleaned and groomed - do you think this disc harrow will help or does the area need to be cleaned more prior? Will the sticks etc just get tangled? We have a 60hp kubota - thank you sir

Too fast, put implement all the way down

you need to open up that disc you need more offset and a little weight to increase downforce. I bolted on railroad tracks to my disc for more down pressure

Going forward with heal on floorboard is not the problem, it’s the lifting to place heal on reverse portion with no where to rest your toes or ball of foot. I have a kubota that I’m renting for a week, and my leg is getting fatigued and cramping up because of this. It’s definitely a bad design for people who will be on tractor for long periods doing repeat forward and backwards moves.

Now how do you use the double break function😂

Awesome vid. Exactly what I wanted to see as far as the capabilities of that tractor and the rotary mower. Thanks!

There is no way in hell this thing weighs just under 700lbs, thats completely false, maybe just under 500lbs but not 700lbs

I think ripping it first with a single or 2 bottom plow then chopping it up with this would be great. I have a 2 bottom plow and it tears it up deep but then i cant ever get it chopped up very smooth.

I just had two acres clear cut. Bought a old dish harrow. Doing the exact thing it works well.

whats the best rpms for brush hogging?

Do you ever disc to enhance native forbs? I'm looking at getting a L3901 and disc. Looking to use it to maintain a stand of switchgrass and disc another part in winter to enhance native forbs. They say you need to disc or burn switchgrass to keep weeds from overtaking it or it getting too thick. My dealer quoted me for DH1060 but for $500 more I could go up a hundred pounds. Not sure if I should spend the extra $500 or just throw some sand bags on this thing for nothing. Thanks.

Great job of listening to the machine, and keeping her within the comfort zone.

Personal opinion, I think this is an excellent demonstration of the advantages of the hst over the gear drive. Can go as slow as needed for conditions without using the clutch.

Seems like less fuss than people are making it out to be

You claim to be southern but pronounce Harrow (hair•row) as opposed to the 400 year old Southern Pronounciation Harr (Hârr)

This is very informative. Thank you. Greetings from Philippines.

Kubota good tractor! Why got on

Tiger Swallowtails