วีดีโอ

turned out amazing! much respect, bro

this is awesome, i need to do my house too, thank god i have a power drill

Awaome man! Gonna save alot thank you!

😂😂hah

For now. I could use the fuel bowl until I change to the new system

Should be a bushing that able to be greased.

Short cuts made by manufacturers is disgraceful.

Make a 90 degree 8" in please.

How much did this all cost if you dont mind? Trying to plan a similar thing so that I dont have to spend 1500 on an efuel kit. Also what brand of fittings?

The 99-2003 is an upgrade and does away with the bottom bolt.

I wish people would put Power stroke or idi on their OBS Videos.

How is this doing and holding up? Any idea if it can take any mods on injectors?

I was going to redoo mine. Just like this one.??? Sum bitch. ? Now what ???😮

Oh hey!

Though you were gonna show us a rebar dance lol 😂

I have to make the same tool tomorrow to remove the front hub nut from my suzuki grand vitara. Was the pipe mild steel or high tensile steel? I have some old water piping laying around, but i think it's only S235 steel.

what fittings exactly did you use for the fuel feed next to the turbo?

Anyone that needs a quick check option you can use a old school tire gauge the kind the stick pushes out of. Just start the truck and hold it on till it stops moving.. watch out!! It can squirt a little.. but it’s fairly accurate

Crap job sorry I had to be honest!

it's crazy because I have a kaufman trailer that is/was gravity tilt. as I wander it I noticed the hing set up was broken on the passengers side. it uses a pin just like that one welded from the outside behind the tire. then there a tube that the p8ns sit it that's a one piece that goes across the whole width of the bottom the trailer with 4 inch long pieced of angle iron on each side of the tube that tie the deck to the Pivot Point and there is no grease fitting whatsoever come to find out the passenger side seized up and broke the pieces of angle iron brighten the bends of them I've sensory welded them and heated the s*** out of that pivot point trying to break all the stuff loose and it has not worked at all so now I'm going to buy aftermarket hinges offline and replace them with ones that are greasable I expected a lot better from Kaufman even though I bought the trailer used trailer used

Is the inspector signing off on it?

second one is what happened to our neighbors, at first they was negotiating prices for their walls from our other neighbor, their talks was going good then a week later they told them they changed their mind. it turns out they choose to have their relative do their home for 20-30% cheaper, 6 months later typhoon came in, their house collapsed and lost a family member because the wall has fell down on him while he's asleep. They nepoContracted their relatives to do the job to frickin save 20-30% of the cost just so that they could have a party once the house is done, Would've been better had they saved it for the funeral.

You get what you pay for he figured he could save a couple thousand on the foundation poor but it will end up costing him 50 in the long run

Thx

yup.. it will twist. You want to tie the walls together. When you terminate your bar in a corner, you end up with two walls.

Pathetic

Could of been a good vdeo if it wasn't for that stupid music

Add fiberglass so it doesn’t break anymore 😊

Sorry can't understand, volume low.

Nice!

Mine has had issues tearing axle fell off a month after. The rear with the max ramps drags EVERYWHERE. Welds are cracking. The deck on max ramps welds have broke. The ramps weigh like 10,000 lbs I had to add a spring to make them manageable. They are junk

A lot of trailers are built like crap. Even old trusted names like PJ. I have one PJ dump. The quality is non-existent. I also have a Load Trail. I have had to re-weld a third of it.

A stupid try to educate others

The wood finish is nice but the ends should have been end grain wood to take it to the professional level.

Great video. Do you have the links to the fuel mounts and fuel pump that you used?

Im seeing what in the wide heck is going on here now

What in the wide heck be going on here

I see Grandpa's crane in the background....I like it!!

still running strong? Any complaints? Im possibly going to purchase one tomorrow. Thanks for sharing 👍🏻

ITS BEEN A WHILE! .... ahem sorry don't know where that came from.

Sorry to hear about that problem, and I agree, that shouldn't happen. Hopefully they have fixed your issue by now. I've had my Iron Bull for a couple years now and I love it. However, it isn't a tilt deck. I'm actually looking to upgrade to a deck over tilt Iron Bull and will definitely see what they've done to solve this issue, thanks for the heads-up. I hope they made it right for you.

There should also be a bushing for that pin to ride in instead of being allowed to just wallow out the hole. This, I suspect, is the main reason for the pins breaking off as that hinge is allowed to rattle and move about the pin. . If you are keeping the trailer, I would add some greaseable bushings and weld them from both sides. Maybe even thicken that hinge plate as well.

If i ave the tardwork weed wacker 48v would my battery woulf fit in that mower to

Качество ужас

H&H is junk as well, had half the tongue fall off on one I had because the welds broke on the pin pivot.

The joys of an old truck amirite

Wow, where are you in the country because that is a lot of rust for a trailer that’s a year old, just asking because I’m in South Texas and my truck is at 07 with like one percent surface rust on the whole truck still going strong.

Calcium stones. Remember this comment in 10 years😂

Very nice work mate! What is the fuel reg and where did you get it?

Sorry its hard to hear you on some parts of the video. But I liked that you showed the defect; people could see it wasn't just you being prejudice. You actually showed the problem.