วีดีโอ

Thank you. Super helpful

I had trouble prying the first (lower) mount, so I nipped off the plastic anchor shaped mount from the back using a set of dikes (side cutters) to remove the cable. Sure it destroys the plastic anchor shaped flare mount, but the new part comes with it so it only saves time to nip it off.

The upper clip requiers a small/slim standard screwdriver to wedge in-between the plastic clip and the slim metal rail it is mounted to. 1) Wedge the screwdriver between metal and plastic clip. 2) Pry down or up on screw driver while simultaneously pulling on clip until it comes off metal mounting rail.

Thanks

This was a lifesaver, thank you

The mechanic is telling me this will cost $577 to fix 🤯 seems very simple😅

Thanks dude, 20 minute fix

absolutely top notch video. thank you

I'm doing this to my car this weekend. There are no codes given neither does the check engine light turn on, the tach meter reads 0 sometimes and my car turns off at red lights or when parked. Wish me luck!

Very helpful video, short and simple straight to the point….

Followed exactly how is described in this video and had a flawless repair. Before repair my vehicle was very herd to start and the tach read 0 when the car was running but no check engine light. Thank you for this video... it was a blessing!

Perfect video man saves anyone between 100 to 1000 dollars with a mechanic

What are symptomes of bad cranck shaft sensor ?

I did this in 30 min and fixed my car thanks dude!

A major detail is to make sure the sensor is almost perfect in the middle and straight in. Also, that the sensor is fully in the the hole. I just replaced the sensor on my 2013 Hyundai accent and I guessed my installment of the sensor was a bit crooked and not fully bolted in so the car would not start afterwards. Recommendation is to lift the O ring to the middle of the part of the sensor it is on . It will make its way down to the base when you ratchet the bolt in.

In another video the sensor was just under the throttle body on the transmission???

2014 Hyundai Accent 1.6L Pretty simple guys just relax watch this video be gentle with electric connectors. Use a flash light 10-20min 5min if proper tools and experience. Car running smooth quite like having a new car and saved about $ 150 dealer ship wanted $175 back order same part no in the description. I paid $25.Total savings 300-500. Genuine Hyundai 39180-2B000 Crankshaft Position Sensor www.amazon.com/dp/B00EVJSSXM/ref=cm_sw_r_apanp_Q4aruii8m3MG9

Can I clean it or only replace it

Thanks for the video changed mine in like 15 min.

Thank you!

Thank you for the perfect explanation. It took me about 30 minutes and this video definitely helped me avoid a lot of struggle that I would have had. To others having the faulty starting and shutting off in traffic, the P0335 error code refers to this part. I previously changed the 2 sensors on top of the engine and the issue persisted. This video is the solution.

Would this prevent the car from starting ?

I got to replace mine on my hynduai accent 2016 and it was not easy‼️😥

Thank you, you helped me. Its th 2nd time happen to me, is it a known problem? Thnx

Thank you so much! I was able to change mine and the car runs like a dream again.

This is a great video! I'm about to give it a shot myself. Before I do so I wanted to ask if this is related to error code P0335 and is this also related to error code P0269?

Just changed mine and car is running like new.

Great video. So once you switch the bad sensor out you are good to go? Nothing like relearning the sensor to your engine needed?

Great video! Thank you

Thank you so much for taking the time and effort to make this. I wouldn't have been able to do it myself, without your help.

Very well done and a big help. Thanks.

Thanks!!

Big Help!!! Thank you.