วีดีโอ

Do you have to prime the new fuel filter by filling it with gas??

What’s the part behind the seat at 2:14 just below your index finger? It’s got a bunch of wire going into a black and gray piece.

Great video How long is the rope

Hello, I have recently just picked up one myself. I was wondering if you know if there are baggers for this mower?

How does the belt go on the spv21

Does everyone have a snow blower who has a house up north ???

First start since last year?

THANKS, perfect et magnifique pour mois.

Thanks for the video. I purchased one and there is virtually no videos for maintenance, other than an oil change. I couldn't get my drain plug loose, so i had the dealership change oil, $165.00, still cant get drain plug to loosen, and i need to do another oil change. Good job!

You made my day! I couldn't figure out how the choke level worked!

You're right there's no videos out here for the bison 400. So thanks for doing this one. I was getting no error code. But the light for the shift position was staying on and it was flickering.Bright dim almost like a turn signal. Also, my fuel pump would come on for 5 seconds.Go off for about ten and keep cycling like that Until I disconnected the battery. Today I hooked it up to start it and when I Started it the starter didn't disengage. Now I have a code: P0351. So i'm thinking I have the same problem.

Working on a ch25s 68704 with almost excessive endplay. Is there a bearing at all for that end of the crank shaft you popped out, or does the crank just ride in there with its seal?

Thanks for the video. 91301-Z9L-000 - O-Ring (19.1X2.2) - Honda Original Part. I bought an o-ring that was a bit wider 19mm inner diameter by 2.5mm width. The wider o-ring is working great.

Just what I needed as having problems with choke!!

Can I use my electric impact drill to remove the bolt??

Thanks . Looks like the ring gear split but I have another flywheel in good shape.

Thats a nice engine

Where could I get that switch ?

Awesome video your a big help keep up the good work 😊

Having the same problem on my 2015 T3000 24 HP same linkage as this video ,you would think they would put the better white plastic little square slide for the cable to slide as needed for Slow -to- Fast -to- CHOKE.... ,keeps bending cable, so i think like you did pull the cable as much as you can & tighten with a T-25 on a socket wrench ,. this video should do the trick to solve this simple stupid mickey mouse Linkage . - Thank you -

Thank you for such a short, to the point, video. Just saved me a bunch of time watching all these other guys fluffing the videos with useless commentary mostly unrelated to the title. Good job!

Is it possible to buy the little plastic piece on that bracket you show in the very beginning?

This saved me more aggravation than you could possibly imagine!!! Thanks so much.

Thank you very much! You helped me solve my issue.

it helped ty

ty

Got one $409 from LOWES, new, year 2k. Made in the USA and it shows...motor runs good but slapped on seals and assembly. Now looking for front valve cover seal and noticed oil weeping in same location as yours. Ist one went back to Lowes due to faulty under deck construction..small twigs get jammed under plastic to metal under deck, bulging plastic down till the blade strikes. We all got that issue that is just piss poor engineering. Somebody posted that flaw here on YTube. If the layer laps were reversed.. then NO problem. Has not done that on second mower..yet. Got 11 year old Chondas with no issues!

How do I know if my pulleys are good?

Thank you thank you, exactly what I needed!

Would this also apply for a Lowe’s 5x8 trailer?

42 "?

42"

How bout dummy flips for tractors?

Hi, need a Carburetor for a 20yr old Briggs and stratton 15.5 IC OHV Craftsman RIDING MOWER.... Could you tell me which one fits?I would greatly appreciate it.....THANKS!

THANK YOU that spring has been making me crazy on how it gos. great video.

Stevie Wonder must be doing quality control for Honda.

180 dollars at the dealer,,,,

Great video. Thanks.

Very informative, thank you

Thank you so much!

I have a 2460 magnum.my batt wire from ignition to regulator always has 12.56 volts.even with key off.is my key ignition bad?when running that wire has 14.9v

I have one that sometimes has to be put I forward gear then reverse for it to back up. I put new belt on it. Did not solve the problem. Sometimes a little jerky in forward too. Maybe I need to relocate spring just a little? I think the Holly’s are good. None broken like that one anyway. Bought the belt from a small engine parts shop/store. Maybe not oem, not sure.

I bought a KIPA carb off Amazon for my B&S 14.5hp rider for $20...been running great for the last 2 years.

Terrible video

Mine has the exact same problem!

Very hard to find any videos or pictures on this rare mower. Great job. Thank you!

Very well done. When I got the tractor from a friend with a new card to install the choke arm was just dangling and I could not figure out where it went this was a huge help.

Gracias

I welded my bolt to a plate so I could get 2 c clamps on either side. but she worked.

Got a used Ariens (same model) for $75 all that was missing was one part from the throttle linkage. Thank you for saving me from hours of confusion!