วีดีโอ

I have the same problem with my CT-F7171. I think it is either the pinch roller, capstan or the motor. Stop the auto shut-off wheel briefly, then the winding wheel also stops, and the load from the winding wheel is gone, but the flutter is still there! Take a recording with a solo piano or acoustic guitar and test it out.

Thank you Helmut 👍

НЕ НАДО НИЧЕГО МЕНЯТЬ С ЛЕВОГО НА ПРАВОЕ ПРИЧИНА В ПОДМАТЫВАУЩЕМ ШПИНДЕЛЕ КОТОРЫЙ БУКСУЕТ НА ФЕТРОВОЙ ШАЙБЕ ПО ПРИЧИНЕ ОСЛАБЛЕНИЯ ДАВЛЕНИЯ ПРУЖИНЫ.ОН НАХОДИТСЯ С ОБРАТНОЙ СТОРОНЫ .И ВЫГЛЯДИТ КАК МЕДНАЯ ШАЙБА ВОЗЛЕ МАХОВИКА.

Could you give me some advice for my Tandberg 9000X?

Hi, very cool video. Good job! I've got the same mini- kompressor. At the end of the black cable, the grey thing is broken. Do u know how i can repair it?

Im having issue with my inflator. My inflator pumps out air but when it's connected to tyre valve, it doesn't pump out air. The hose connectors are good. What else could be the problem?

I owned something similar decades ago long before CDs arrived. It was a unit that was a slightly lower level product to the Garrard transciption turntables 301 and later 401 favoured by broadcasting concerns and dyed-in-the-wool fans of Hi-Fi "separates".

Low quality gadget, and very vague. Mine shows more than 1 bar Up .

*******

Nice video

Nice work, Oliver. I have a type A Mark II as well. Mine is the darker metal, but everything looks to be the same, right down to the mechanisms. Like another poster mentioned, VM Audio Enthusiasts are a good source for the idler wheels. They do require you trade in your old idler wheel. As far as a cartridge, I had mine outfitted with an Ortofon Red. The headshell sits lower to the record, lower than what yours seems to be riding at. Sounds great though.

I have one in excellent working order. Love the sound. Surprised to hear you say that it's comparable to Revox. From everything I've read online, people consider Studer/Revox as the best of the best in tape decks.

Mine managed to have/end up with a tear in the ribbon pretty much underneath the glass. To hard to hack solder

Sounds wonderful. Surprising. Even with that heavy arm.

The drive axle cannot wear on plastic, maybe the plastic drive hub itself has an eccentric hole, wow, a million miles on that machine!

Try switching the right one for the left one as it is only used in rewind mode and may not have wear issue the right one develops over time??

Try switching the right one for the left as it is only used in rewind mode??

Thank you very much for the information it fixed it right up I couldn't believe it Good man awesome

I also have one of these, &, unfortunately, I was not able to have it repaired at my trusted Audio/Video Shop. Don't know why, exactly, but I still have it. Perhaps ..I simply like the way it looks with the cool blue light where the cassette is inserted. I still...powers up and all the lights work, it just...won't...do anything else.

Nice review and display. I ran thru most of Tandberg's tape decks, starting with the 64x model! I actually now have the latest Tandberg tape deck, the TD 20A. Do you do anything with these? I live in the Phoenix, AZ area.

thank you a lot for your video.. thanks to you i repaired mine.

Good Job. TY. 🙏🏻

I see this was 3 years ago but if you still have this and are still looking VM Audio Enthusiasts can help you out with that idler wheel. I have purchased a couple from them for my Garrard Type A turntables.

I have one mint condition

the problem is the piston does not get any air !!!!! if you remove side black metal plate and drill a small hole 3mm on the top, because this thing has no air intake for the piston .. i did the hole and i gives more air

Just tried on mine it did not work at all - thanks a lot for the video anyways!

It's fixed the same issue I had. Thanks for sharing 👍

Do they use a específico needle

Nice overview thanks. I have a 3341X which is cheaper but evidently shares some of the features of this. Just been repaired and serviced in the UK and it's as good as new - almost. The 9000X series I could never afford at the time but it's great to see a working one!

My abandoned air compressor back to life! Just like new .. thank you so much

You only need to change one pinch roller!!!

where did you find a new pinch roller ?

Hi mine pumps but very weak pressure ! The piston seals look like a silicone oring! Do you know where to buy these orings ? Any reply appreciated thanks from Australia!

I have red rubber grease from car brake piston repair, stops rubber swelling apparently 😀

Mine does not restart if the pressure reaches about 2 bar, but if I remove the pipe from the tire It will start. It seems as if it does not have enough torque to start. You mentioned this symptom in the video. I checked the valves and they seem to be ok. I checked the alignment of the piston and the cylinder which seems ok too. I have no idea. It is like that from day 1, but I have lost the bill to exchange it.

thanks for your video, mine just needed greasing up thankfully

Thank you for posting video, the steps you explained was very informative. Normally what is life span of tyre inflator if use 5 minutes per day??

Can you upload a video detailed for the wiring setup ? The grey wire the green ground wire and the brown wire ? What goes where ? I have a EICO ST 40 how do i connect it all

Hi, I have one of these. It uses the same mechanism as the far more common CTF2121 so perhaps pick up a non working 2121 and use the transport.

Indeed it's a shame that parts are no longer available from Pioneer. I am trying now to resurrect the very same deck, i.e CT-F7171. If yours is not repairable, would you consider parting it out?

Thank you 👍

I tried this on my autel but it did not work still blank screen Thank you for the idea anyway it was worth trying I wish these things cam with a refresh / reset button I think my contrast is way to high and blank my screen out?

Does anyone know who might fix these? I have one that looks like the machine above. Parts are hard to come by these days.

modern stereo records make the needle vibrate diagonally

very nice sounding , ronette cartridges really have a nice timbre

collaro changers around that era could be used manually too

Mine was just turning off after it felt hot. Replacement unit did the same thing

It worked, thank you

THANK YOU... will try. Hopefully it works