วีดีโอ

Hahaha. Thanks for saving me my time 😅

I can't believe I watched this crap

I want that 9 min of my life back

Seriously???? 😳

Надо затачивать на камне и своевременно сверло охлаждать водой 🚰... Метал нагревается 😢😢😢... Будет мягче если не охлаждать ❗❗❗

Угол 📐 заточки ❗ Надо изменить чуть , пятку сверла сделать пониже режущей части ❗. И будет нормально 👌. Под каждый метал 🕸️ угол сверла разный будет... Оно должно сверлить хорошо 👍 , чтобы выходила спираль металла а ни мелкая стружка .....

Way too much trouble.

You're an absolute dumb fuck if you think this sharpens your knife.

other smd LED will be burn very soon. Shorting will just distribute burn LED voltage to other led. Efficient solution is to use resistor or replace with new SMD led from other old bulb

Good ❤❤❤

Ah ah ah !

This was a waste of time. Clearly lacks attention to detail and is making trash for asmr value

"Wow, this video is so well-made! I recently tried something similar on my channel - would love your thoughts on it! 😊" 25:00

Klicbajty!!!!! Klicbajty!!!!!!! Klicbajty!!!!!!!🤮🤮

Super video well done 👍🏻

Before you try any of these ideas, please consider how safe the setup is. I am naturally very afraid of my 2 angle grinders, so i tread very cautiously with them. They are designed to be held in the hand with the switch off easily reached and activated in case of emergency. I have a good vice, but putting an angle grinder in it could be very dangerous if it works loose with the vibration. How on earth will you turn ot off if it suddenly comes loose unless you rig up a safety cut-off switch, which you can easily access? Likewise how safe is the jig for the drill unbit sharpening. I feel it should be securely held in a jig so it cannot be ripped from a ha d grip. Tak8ng shortcuts with safety is just not worth it. I have seen horrendous accidents such as fingers cut off, eyes lost, and hearing damage. One of the most stupid was a roofer who rather than use a proper scaffold took his van, laid a ladder flt on the van roof, climbed up and balancing himself proceeded to install the guttering. You can imsgine what happened.

Cant wait to watch this.

For the love of god, tighten the hinge up on those snips! 🤣

Бля весь станок ходуном ходит

Шуруп закрутить не можешь, ножовкой пользоваться тоже проблема,но зато можешь заточить сверло😂

I will send u money to buy a new slippers for u but don't give wrost nd useless ideas on TH-cam please

Bro.. buy a new pair of slippers to make this video

Thank you.

Автор видео или мазохист или рукажопый. 1 способ сверло да заточил, но оно у него дырки треугольные сверлит, не отверстия. 2 способ стамеска как была тупая такой она и осталась. 3 способ нож такой же как и стамеска. Ножу угол заточки не правильно сделал как мне показалось ( но не утверждаю) видно что он плохо режет. 4 способ А топор как говорят ладошкой по мохнатке поводил. Какой был такой и остался. Он им просто после яко бы заточки сильней бить стал

Мастер, а без ключевой патрон поставить и не жечь руки, не хватает ута🤦🤯 А потом учим людей,а сами не знаем азов.🤑👋

Nossa a afiação da broca foi um horror, o furo ficou ovalado...👎

Bileme ile ilgili güzel bilgilerin de verildiği bir video ancak, gereğinden çok fazla uzun olmuş.

So schärft man kein Werkzeug. Völlig falsch.

Fantastic

🎉🎉

Pra cortar sabão ficou ótimo kkk

A altura só serve pra essa broca .muda o foco é se sabe se é mesma broca .

Что ты за фуфло тут лепишь

That has to be the most stupid and useless video that i have seen on sharping tools on TH-cam 😢

Vichiiiiiii poderia ao menos tirar da função martelete kkkkkkkkkk

Afio todas as brocas de aço rápido na minha serra mármore

Tirou do martelete deu certo né esperto 😂

Il perce avec la percussion

Please use grinding wheel to sharpen drill and honing stone for chisel, don’t heat drill it softens it

com a esmerilhadeira ficava melhor

ficou péssima a afiação 😂😂😂

pra que aquecer a broca pra destemperar a broca fala sério 😂😂😂😂

perde muito tempo quem não sabe afiar broca,por isso que eu deletei o Facebook fala muita bobagem e se falar mal do Lula ele apaga bobagem não saber afiar broca eu faço isso há quase 40 anos 😂😂😂😂😂

Very very bed engineer. One time plz. Come to my shop 😂

‼️‼️Er arbeitet sehr ungenau und nicht sicher und stabil‼️‼️

👍👍🙏🙏

stupid idea, u are sanding the block of wood too.

Я столяр с 50 летним стажем.Ради интереса попробовал способ номер 2 ,как заточить стамеску.ужас,а не способ.Даже не пытайтесь использовать

Thanks, I like that.

Thankyou for your sharing information