PLUKI 4X4
PLUKI 4X4
  • 82
  • 172 862
How to Install Niva Power Steering in a Lada 2107: Complete Guide
In this video we are installing power steering box on my lada 2107 it is the same process for lada 2101 - 2107 and for niva without power steering.
If you have any questions, please feel free to leave it in the comment section below.
Go ahead and follow me on insta: 4x4pluki
#lada #ladaniva4x4 #ladaniva
Thank you for watching! Please like, share and subscribe!
Disclaimer:
Due to factors beyond the control of Pluki 4x4, I cannot guarantee against improper use or unauthorized modifications of this information. Pluki 4x4 assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. Pluki 4x4 recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of Pluki 4x4 , no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Pluki 4x4
มุมมอง: 334

วีดีโอ

How to Install Transfer Case Support?
มุมมอง 93421 วันที่ผ่านมา
Hi guys, today we are installing anti vibration transfer case support. One of the best mods you can do to your Niva!! When you drive your niva after installing transfer case support you will feel really big difference in comfort. If you have any questions, please feel free to leave it in the comment section below. Link for transfer case support: ladapower.com/catalog/transfer-case-2/lada-niva-t...
Engine Swap Success! Niva Engine Installed in Lada 2107 - First Startup
มุมมอง 598หลายเดือนก่อน
Hi guys, I swapped a Niva engine into my Lada 2107 and it's finally time for the first start! Watch as I take you through the final steps of the swap and see if this beast roars to life. Will it start? Let’s find out! If you have any questions, please feel free to leave it in the comment section below. Go ahead and follow me on insta: 4x4pluki #lada #ladaniva4x4 #ladaniva Thank y...
How to Maintain a Lada?
มุมมอง 903หลายเดือนก่อน
Today we need to do basic maintenance on my lada niva! and to see if there is more problems with my car. Oil change video: th-cam.com/video/Niq_ecKe_8o/w-d-xo.html If you have any questions, please feel free to leave it in the comment section below. Go ahead and follow me on insta: 4x4pluki #lada #ladaniva4x4 #ladaniva Thank you for watching! Please like, share and subscribe! Dis...
Lada Engine Swap: Step by Step Engine Removal
มุมมอง 5632 หลายเดือนก่อน
In this video, I'll show you the step-by-step process of pulling the engine out of a Lada 2107. From disconnecting all the necessary components to safely removing the engine, follow along as I tackle this DIY project. Whether you're a seasoned mechanic or a car enthusiast, this guide will help you navigate the engine removal process with ease. If you have any questions, please feel free to leav...
Lada Maintenance: Easy Tie Rod Kit Replacement
มุมมอง 1K5 หลายเดือนก่อน
Learn how to replace the tie rod kit on your Lada effortlessly with our step-by-step guide. Keep your car running smoothly with this essential maintenance tutorial. Watch now! If you have any questions, please feel free to leave it in the comment section below. Go ahead and follow me on insta: 4x4pluki #lada #ladaniva4x4 #ladaniva Thank you for watching! Please like, share and su...
1K SUBSCRIBERS CELEBRATION + LADA BMW 1.8 PROJECT REVEAL
มุมมอง 5706 หลายเดือนก่อน
I just wanted to take a moment to express my heartfelt gratitude for helping us reach 1,000 subscribers on TH-cam! 🎉🙌 I'm beyond excited and incredibly thankful for each and every one of you who has subscribed, liked, commented, and shared our videos. Your support means the world to me, and it motivates me to keep creating content that you enjoy. Whether you've been with me since the beginning ...
How to Replace a Heater Core on LADA
มุมมอง 8036 หลายเดือนก่อน
Hi guys, today I need to replace my heater core on lada niva. If you have any questions, please feel free to leave it in the comment section below. Go ahead and follow me on insta: 4x4pluki #lada #ladaniva4x4 #ladaniva Thank you for watching! Please like, share and subscribe! Disclaimer: Due to factors beyond the control of Pluki 4x4, I cannot guarantee against improper use or un...
How to Replace an Alternator on Lada Niva
มุมมอง 1.9K7 หลายเดือนก่อน
Hi guys, its time to replace mine alternator on my LADA NIVA with stronger one! If you have any questions, please feel free to leave it in the comment section below. Go ahead and follow me on insta: 4x4pluki #lada #ladaniva4x4 #ladaniva Thank you for watching! Please like, share and subscribe! Disclaimer: Due to factors beyond the control of Pluki 4x4, I cannot guarantee against ...
How to Replace a Windshield Wiper Motor on Lada Niva? (DIY)
มุมมอง 9627 หลายเดือนก่อน
Hi guys, if your wipers are moving slow or they are completely dead there is a big chance you need to replace your windshield wiper motor. If you have any questions, please feel free to leave it in the comment section below. Go ahead and follow me on insta: 4x4pluki #lada #ladaniva4x4 #ladaniva Thank you for watching! Please like, share and subscribe! Disclaimer: Due to factors b...
Front End is Done!! for now... // Ep 13
มุมมอง 8368 หลายเดือนก่อน
Front End is Done!! for now... // Ep 13
How to Change a Thermostat on Lada Niva
มุมมอง 2.2K8 หลายเดือนก่อน
How to Change a Thermostat on Lada Niva
How to Replace Clutch Master Cylinder and Slave Cylinder? (COMPLETE Guide)
มุมมอง 5K9 หลายเดือนก่อน
How to Replace Clutch Master Cylinder and Slave Cylinder? (COMPLETE Guide)
Cutting The Front End Off my Lada! // EP 12
มุมมอง 1.3K9 หลายเดือนก่อน
Cutting The Front End Off my Lada! // EP 12
DIY Bed Liner Paint Job on Lada Niva!!
มุมมอง 1.4K10 หลายเดือนก่อน
DIY Bed Liner Paint Job on Lada Niva!!
DIY Bodywork and Welding: Repairing and Fabricating
มุมมอง 1.1K10 หลายเดือนก่อน
DIY Bodywork and Welding: Repairing and Fabricating
Say Goodbye to Rust: Protect Your Interior Now!
มุมมอง 1.9K11 หลายเดือนก่อน
Say Goodbye to Rust: Protect Your Interior Now!
How to Replace Brake Pads on LADA NIVA (COMPLETE Guide)
มุมมอง 1.8K11 หลายเดือนก่อน
How to Replace Brake Pads on LADA NIVA (COMPLETE Guide)
How to Change Your Oil on Lada Niva
มุมมอง 4.4K11 หลายเดือนก่อน
How to Change Your Oil on Lada Niva
First Wash in 15 Years!! Lada 2104
มุมมอง 360ปีที่แล้ว
First Wash in 15 Years!! Lada 2104
Everything Wrong With my Cheap LADA 2104
มุมมอง 516ปีที่แล้ว
Everything Wrong With my Cheap LADA 2104
I bought my Dream Daily!!
มุมมอง 510ปีที่แล้ว
I bought my Dream Daily!!
Putting some Off-road Lights on Lada Niva
มุมมอง 1.1Kปีที่แล้ว
Putting some Off-road Lights on Lada Niva
My First Big Mistake // Ep 11 Removing all the glass and doors
มุมมอง 632ปีที่แล้ว
My First Big Mistake // Ep 11 Removing all the glass and doors
Fix your Exhaust before its too Late!!
มุมมอง 996ปีที่แล้ว
Fix your Exhaust before its too Late!!
How to Change a Fuel Pump on Lada Niva
มุมมอง 4.4Kปีที่แล้ว
How to Change a Fuel Pump on Lada Niva
To Save or Not to Save: Help Me Decide!
มุมมอง 1.1Kปีที่แล้ว
To Save or Not to Save: Help Me Decide!
Removing Rear Differential and LPG Tank from LADA NIVA // EP 9
มุมมอง 2.1Kปีที่แล้ว
Removing Rear Differential and LPG Tank from LADA NIVA // EP 9
Removing Everything else from the Interior on my LADA NIVA (everything is out!!) // Ep8
มุมมอง 3.7Kปีที่แล้ว
Removing Everything else from the Interior on my LADA NIVA (everything is out!!) // Ep8
Lada Niva Lower Ball Joint Replacment (timelapse)
มุมมอง 1.3Kปีที่แล้ว
Lada Niva Lower Ball Joint Replacment (timelapse)

ความคิดเห็น

  • @MarkusNuorala
    @MarkusNuorala 7 วันที่ผ่านมา

    Hey Pluki!🤝 what tire in this vaz?

    • @PLUKI4x4
      @PLUKI4x4 7 วันที่ผ่านมา

      Tires in this video are BFGoodrich Mud Terrain TA KM2 215/75 R15

  • @europeanpaganismrising2022
    @europeanpaganismrising2022 8 วันที่ผ่านมา

    N̈amam reči majstor sam takav.

    • @PLUKI4x4
      @PLUKI4x4 8 วันที่ผ่านมา

      😎

  • @shrekulous3753
    @shrekulous3753 8 วันที่ผ่านมา

    only in a Lada can you use any parts you find and have it work perfectly

    • @PLUKI4x4
      @PLUKI4x4 8 วันที่ผ่านมา

      You are absolutly right my friend, that is way I love my lada🤗

  • @leonardasmigmator784
    @leonardasmigmator784 8 วันที่ผ่านมา

    Great video 😊

    • @PLUKI4x4
      @PLUKI4x4 8 วันที่ผ่านมา

      Thank you!!

  • @derphilipp5369
    @derphilipp5369 10 วันที่ผ่านมา

    I'm planning to put the 21214 Niva engine in my Lada 2101 from 1978. It does not have electric fan for cooling. What should I do? Use a fan from 2105? Any idea?

    • @PLUKI4x4
      @PLUKI4x4 10 วันที่ผ่านมา

      You are right, just use the fan from 2105 or 2107, In my videos I will do some work to make realy good electric fan wiring but first I need to finish bodywork, there are some awesome videos on yt on how to connect your electric fan. Easiest thing to do is to put 2105 fan. Wish you a good luck!

    • @derphilipp5369
      @derphilipp5369 10 วันที่ผ่านมา

      @@PLUKI4x4 thank you very much!

    • @PLUKI4x4
      @PLUKI4x4 10 วันที่ผ่านมา

      No problem 🤗

  • @alenbitici9919
    @alenbitici9919 10 วันที่ผ่านมา

    U 18:15

  • @alenbitici9919
    @alenbitici9919 10 วันที่ผ่านมา

    13.10.2024

  • @alenbitici9919
    @alenbitici9919 10 วันที่ผ่านมา

    Ja sam te vidio

    • @PLUKI4x4
      @PLUKI4x4 10 วันที่ผ่านมา

      Danas se malo vozikao po gradu😁

  • @PHRtv
    @PHRtv 11 วันที่ผ่านมา

    Hi Pluki, love the videos! What tool and dimensions did you use to unscrew the oil pan drain plug? Keep the videos coming!!!

    • @PLUKI4x4
      @PLUKI4x4 11 วันที่ผ่านมา

      Hi, you need to use Hexagon 12mm tool. Thank you so much I will!

  • @davidlongworth1755
    @davidlongworth1755 14 วันที่ผ่านมา

    I like the dark red. Just asking is that the texture you wanted. I am no car painter but isn't that what they call orange peel as in not a fine smooth finish? Apart from that your presentation videos are very helpful. Keep doing them.

    • @PLUKI4x4
      @PLUKI4x4 13 วันที่ผ่านมา

      Thank you! This is special color with that ruff finish, you can google Raptor paint to see car like that, orange peel is when you paint clear coat on normal paint job, I didn't put clear cout on my niva. Thank you so much for your comment!

  • @alfonsotartaglia7086
    @alfonsotartaglia7086 14 วันที่ผ่านมา

    Great content mate

    • @PLUKI4x4
      @PLUKI4x4 14 วันที่ผ่านมา

      Thank you so much!

  • @alfonsotartaglia7086
    @alfonsotartaglia7086 14 วันที่ผ่านมา

    Hello mate! I think that this is the right direction for your channel. People want to learn how to work on their Niva and you are a great teacher! please do more videos especially on general maintenance! thank you and keep up with the good work

    • @PLUKI4x4
      @PLUKI4x4 14 วันที่ผ่านมา

      Thank you so much mate! I have about 10 more video ideas at the moment on how to maintain and fix your niva, I just need to record it😁

  • @niva1608
    @niva1608 22 วันที่ผ่านมา

    koja je razlika sa ovim nosacem nesto mi se cini u blato i snijeg da bi glavio u to ?

    • @PLUKI4x4
      @PLUKI4x4 22 วันที่ผ่านมา

      Iskreno imao sam to na staroj nivi, i dalje najniže točke su diferencijali, tako da ako baš nije netko strmo brdo i odmah strma nizbrdica neces strugati sa time

    • @niva1608
      @niva1608 22 วันที่ผ่านมา

      @@PLUKI4x4 a reci mi da li je bas osjetno smanjena vibracija i brujanje?

    • @PLUKI4x4
      @PLUKI4x4 22 วันที่ผ่านมา

      instalirao na jedno 5 niva barem i stvarno se osjeti ako se napravi i poštela kako treba, ja na svoju sigurno vraćam, govorim o ovoj nivi koju potpuno restauriram, a na daily nivu neću staviti zbog vremena i novaca inaće definitivno bi. Smanjuje se dosta vibracija brujenje ne toliko

    • @niva1608
      @niva1608 22 วันที่ผ่านมา

      @@PLUKI4x4 pravim i ja jednu sve iznova pa zato pitam hvala na informacijama

    • @niva1608
      @niva1608 22 วันที่ผ่านมา

      @@PLUKI4x4 i jos jedno pitanje da li je skupo i tesko ugraditi servo na nivu 1.7 karburator ?

  • @Ivan-L.
    @Ivan-L. 22 วันที่ผ่านมา

    Great work mate :) Can you provide a link from where you bought ist? Thanks in advance and greetings from Bosnia :)

    • @PLUKI4x4
      @PLUKI4x4 22 วันที่ผ่านมา

      Sorry I tought I put it... here it is ladapower.com/catalog/transfer-case-2/lada-niva-transfer-case-3-point-support-with-guard-t-sphera-detail Greetings from Croatia ;)

  • @leonardasmigmator784
    @leonardasmigmator784 22 วันที่ผ่านมา

    Thanks for showing us 💪

    • @PLUKI4x4
      @PLUKI4x4 22 วันที่ผ่านมา

      No problem 😁

  • @orangek5
    @orangek5 22 วันที่ผ่านมา

    got one too but also my gearbox is on the frame, so no sepperate support anymore for the gearbox.

    • @PLUKI4x4
      @PLUKI4x4 22 วันที่ผ่านมา

      That is awsome!!!

  • @freedoompictures6839
    @freedoompictures6839 22 วันที่ผ่านมา

    I did this mod to my 2018 Niva and since then driving the car is much more comfortable compared to factory. Beyond comfort one more disadvantage of factory transfer case arrangement is that it exposes a small area of the monocoque chassis to highly focused vibrations. This causes metal fatigue in a small area which becomes prone to rust and decay development much quicker than it should. So you do this mod, and make sure to use protective coating like teroson or similar to the modified area, then you're actually in a better situation in terms of rust protection for your car.

    • @PLUKI4x4
      @PLUKI4x4 22 วันที่ผ่านมา

      Everything you just said I 100% agree with you!

    • @buongiornosanpietro6911
      @buongiornosanpietro6911 12 วันที่ผ่านมา

      hi, i'm about to install this modification, can you tell me exactly which part is most exposed to corrosion? so i understand and follow your advice. thanks

    • @PLUKI4x4
      @PLUKI4x4 12 วันที่ผ่านมา

      The part where transfer case mounts original are, just clean good with wire brush and protect it. Wish you a good luck with installation.

    • @buongiornosanpietro6911
      @buongiornosanpietro6911 12 วันที่ผ่านมา

      ​@@PLUKI4x4 thank you 😊

  • @niva1608
    @niva1608 หลายเดือนก่อน

    Da li si na nivu dodavao ispod grede uz one i ojacavao ono dje se uporne spone kace i naprijed ?Radim jednu citavuod nule pa nemam ideju kako da je ojacam da ne postoji sansa u slucaju da me povuce neko iz snjega da izleti pola nje kao sto se desava 😂

    • @PLUKI4x4
      @PLUKI4x4 หลายเดือนก่อน

      Nisam nikada tamo ojacavao ali cupali me iz svega nikada nije bilo problema, samo dobro sve složi i ukloni hrđu, a za ojacanje najbolja dodaj jos 2mm lima pa si miran

    • @niva1608
      @niva1608 หลายเดือนก่อน

      @@PLUKI4x4 a sta mislis ima li potrebe da dodam kutije metalne one kao sto ima ispod .Lada je zdrava bas nidje ispod rdje nema .To je ova crvena ima je na you tub u short na moj kanal

    • @PLUKI4x4
      @PLUKI4x4 หลายเดือนก่อน

      Nikada to nije lose napravit

  • @matyasantal6715
    @matyasantal6715 หลายเดือนก่อน

    Finally, it's makin a shape 🎉

    • @PLUKI4x4
      @PLUKI4x4 หลายเดือนก่อน

      Yeah! Its going to be awesome!!!!

  • @anahorvat4036
    @anahorvat4036 หลายเดือนก่อน

    Keep it up man 👌

    • @PLUKI4x4
      @PLUKI4x4 หลายเดือนก่อน

      Thanks!

  • @leonardasmigmator784
    @leonardasmigmator784 หลายเดือนก่อน

    Great video 😊

    • @PLUKI4x4
      @PLUKI4x4 หลายเดือนก่อน

      Thank you!!

  • @dronephotography-by-Jerko
    @dronephotography-by-Jerko หลายเดือนก่อน

    Samo naprijed Lada Freak,..... great video, need lot of time to do it

    • @PLUKI4x4
      @PLUKI4x4 หลายเดือนก่อน

      Thank you!!! Cant wait to drive it😎😎

  • @europeanpaganismrising2022
    @europeanpaganismrising2022 หลายเดือนก่อน

    Kaj bu 4x4 ili bu zadnji pogon.

    • @PLUKI4x4
      @PLUKI4x4 หลายเดือนก่อน

      Zadnji samo motor pripasujem, treba mi nešto za svaki dan jer se u nivi uvijek vozim, i dosta mi😅

    • @dronephotography-by-Jerko
      @dronephotography-by-Jerko หลายเดือนก่อน

      @@PLUKI4x4 hahahaahahah

    • @PLUKI4x4
      @PLUKI4x4 หลายเดือนก่อน

      @@dronephotography-by-Jerko 😂

  • @paulwalker427
    @paulwalker427 หลายเดือนก่อน

    great video

    • @PLUKI4x4
      @PLUKI4x4 หลายเดือนก่อน

      Thank you!!

  • @wouterschindler1421
    @wouterschindler1421 หลายเดือนก่อน

    Lada god

    • @PLUKI4x4
      @PLUKI4x4 หลายเดือนก่อน

      Thank you!!

  • @WaplogLuisi
    @WaplogLuisi หลายเดือนก่อน

    I have a public of almost 10 k people waiting to see guides and step by steps but for Ladas. Improvements , and such.,.

    • @PLUKI4x4
      @PLUKI4x4 หลายเดือนก่อน

      Cool!

  • @WaplogLuisi
    @WaplogLuisi หลายเดือนก่อน

    Hey my friend good videos. I need a Lada engine bro! How can I get one ...those are strong engines

    • @PLUKI4x4
      @PLUKI4x4 หลายเดือนก่อน

      Thank you! Well that is up to you, try ebay or try to find it locally

    • @WaplogLuisi
      @WaplogLuisi หลายเดือนก่อน

      @@PLUKI4x4 Is for Cuba bro

  • @alexanderpeche6404
    @alexanderpeche6404 หลายเดือนก่อน

    Thank you!!!!! You encouraged me to do it for myself and I got it 💪

    • @PLUKI4x4
      @PLUKI4x4 หลายเดือนก่อน

      That is awsome!!! Glad I can help you🤗

  • @farkashfaloop1854
    @farkashfaloop1854 หลายเดือนก่อน

    Another helpful video! In my Lada Niva the Cool steam tank (6:42 in the video in the down right corner) is full with black dirt. what to do?

    • @PLUKI4x4
      @PLUKI4x4 หลายเดือนก่อน

      I would flush your coolant, maybe remove and wash your radiator, and if its time you can replace thermostat, water pump and hoses, just be sure to clean everything

  • @europeanpaganismrising2022
    @europeanpaganismrising2022 หลายเดือนก่อน

    Provjeri gumu od hardijevog zgloba taman joj je vrjeme za zamjenu.hoće lagano popucat košta 20eura ak pukne može šteta bit preko 100eu. Ak buš mjenjao otpusri kardan i mjenjač metneš nutra .lim na gumi se miče kad je sve namješteno.pozz.

    • @PLUKI4x4
      @PLUKI4x4 หลายเดือนก่อน

      E bravo!!! Uskoro ću ju mjenjati zaboravio napomenuti u videu, hvala puno na komentaru!!

  • @freedoompictures6839
    @freedoompictures6839 หลายเดือนก่อน

    It'll be good to check if you installed the air filter in correct orientation. There should be an arrow sign at the base of the air filter housing that points to the direction air filter's leaves should run parallel to. Yours seemed wrong orientation to me. Not the end of the world to install wrongly, but in the end it might have an effect on the air flow and dirt disposition.

    • @PLUKI4x4
      @PLUKI4x4 หลายเดือนก่อน

      Thank you, I am pretty sure I did how you said it needs to go but I will check to be sure. Awesome tip I forgot to mention!

  • @TheVcasf
    @TheVcasf หลายเดือนก่อน

    Hi. My 2009 Niva lost it's power after an engine change. It drives "ok", yet accelerating from a stop on a hill is impossible without low gear. It just dies. With low gear it jumps just fine. Does anyone know what it might be? I changed everything i can think of. Changed spark plugs, all oils, belts etc. No codes from OBD scanner. Did a catalytic converter delete.

    • @PLUKI4x4
      @PLUKI4x4 หลายเดือนก่อน

      Hi, it can be a lot of isuse, maybe feul pump, maybe distributor, or new engine isnt built right, sadly I cant help you a lot but I would first check feul if this was my car

    • @TheVcasf
      @TheVcasf หลายเดือนก่อน

      @@PLUKI4x4 Thank you for your reply and your great videos. Amazing. So I checked the fuel filter and the car doesn't have any symptoms of fuel pump. I might be wrong. but it drives well once moving. Very strange.

    • @PLUKI4x4
      @PLUKI4x4 หลายเดือนก่อน

      Thank you for your comments! Its really weird but probbaly then its something with sensors or distributor if we assume your new engine is in good shape, do you have any problems in driving or just when you are on a hill?

    • @TheVcasf
      @TheVcasf หลายเดือนก่อน

      @@PLUKI4x4 It only happens accelerating uphill. But I guess it must have lost power overall. but up hill is impossible without riding the clutch or low gear. I've tried everything and might decide to just change the engine again, even though it sounds good and good compression. Thanks again for your time

    • @PLUKI4x4
      @PLUKI4x4 หลายเดือนก่อน

      @@TheVcasf I would check timing before pulling the engine out

  • @shrekulous3753
    @shrekulous3753 หลายเดือนก่อน

    Power steering and AC? Will it even be a Lada anymore?

    • @PLUKI4x4
      @PLUKI4x4 หลายเดือนก่อน

      It's going to be a ladamobile😎 if I find all the parts for AC, I cant remember where I put it😅

  • @TheVcasf
    @TheVcasf 2 หลายเดือนก่อน

    Thank you

    • @PLUKI4x4
      @PLUKI4x4 2 หลายเดือนก่อน

      Always here to help

  • @farkashfaloop1854
    @farkashfaloop1854 2 หลายเดือนก่อน

    Love your channel! are you getting the parts online or locally?

    • @PLUKI4x4
      @PLUKI4x4 2 หลายเดือนก่อน

      Thank you so much!! Most of the parts I get locally but aftermarket parts I got online

  • @publicdomain9400
    @publicdomain9400 2 หลายเดือนก่อน

    What brand of ac is your niva equipped with ?

    • @PLUKI4x4
      @PLUKI4x4 2 หลายเดือนก่อน

      I really don't know, I bought it with ac

    • @publicdomain9400
      @publicdomain9400 2 หลายเดือนก่อน

      ​@@PLUKI4x4 I have a very similar one and it's a diavia that's why I asked

  • @ByDemonsBeDriven
    @ByDemonsBeDriven 2 หลายเดือนก่อน

    Upgrading klimu! Vifis da je globalno zatopljenje u djiru. ;)

    • @PLUKI4x4
      @PLUKI4x4 2 หลายเดือนก่อน

      Baš tako i ja razmišljam bude išla klima unutra 😅😁

  • @leonardwagstaff1363
    @leonardwagstaff1363 2 หลายเดือนก่อน

    I have A/C in my Niva, although we don't have that many hot days in the UK it's a blessing on the days when it is hot, plus it's great to quickly demist windows, so I say as you have pretty much everything you need do it🙂.

    • @PLUKI4x4
      @PLUKI4x4 2 หลายเดือนก่อน

      Yeah, this is starting to be a biger project than I thought, so I will probably install A/C, I have A/C from niva but I will modify it for lada 2107

    • @MrUberjan
      @MrUberjan 2 หลายเดือนก่อน

      AC niva!? Was it hard to install?

    • @PLUKI4x4
      @PLUKI4x4 2 หลายเดือนก่อน

      I bought it with A/C, but it can really be pain in the... to install it

  • @leonardasmigmator784
    @leonardasmigmator784 2 หลายเดือนก่อน

    Welcome back🎉

    • @PLUKI4x4
      @PLUKI4x4 2 หลายเดือนก่อน

      Thank you 🤗🤗

  • @matyasantal6715
    @matyasantal6715 2 หลายเดือนก่อน

    Well, finally🎉

    • @PLUKI4x4
      @PLUKI4x4 2 หลายเดือนก่อน

      Sorry for not uploading I was crazy busy with work. I will go back now to posting new video every two weeks. Thank you for your comment!

  • @Random-nf7qb
    @Random-nf7qb 2 หลายเดือนก่อน

    Why not port the 2105 head and make it accept the fuel injectors? The belt 2105 engine runs a lot quieter and smoother.

    • @PLUKI4x4
      @PLUKI4x4 2 หลายเดือนก่อน

      In my country its a lot easier to find parts for 1.7i then any other engine, and 1.7i engine you can find here for cheap. That is the main reason because I want to make this car my daily drive so its important to me that I can fined parts easy and for cheap.

  • @FluxPod2024
    @FluxPod2024 2 หลายเดือนก่อน

    Keep going good work bro !

    • @PLUKI4x4
      @PLUKI4x4 2 หลายเดือนก่อน

      Thank you so much!!!

  • @mpeg2000
    @mpeg2000 2 หลายเดือนก่อน

    Appreciate you doing these videos in english brother! 👍🏻 Quick question. In the last year my lada didn't start 3 times. Everytime it started again after i hit the starter with a hammer. No problems after that untill a few months later when it happened again. Is this normal and i should just have a hammer ready or is this a sign that i will need to replace the starter? Thanks in advance!

    • @PLUKI4x4
      @PLUKI4x4 2 หลายเดือนก่อน

      At some point in the future starter will fail, but that can be really a lottery, it can fail tommorow or for a year. Thank you so much for your comment 😁 p.s. First thing I would do is clean contacts on the starter motor

  • @niva1608
    @niva1608 2 หลายเดือนก่อน

    sta je sa proektima kako napredujes

    • @PLUKI4x4
      @PLUKI4x4 2 หลายเดือนก่อน

      Ogromna gužva sa poslom bila, ide novi video ne ovaj utorak nego idući pa opet idu videii svaka dva tjedna 😎

  • @brentjoubert-fr1tu
    @brentjoubert-fr1tu 3 หลายเดือนก่อน

    Hey man! Thanks very much for your awesome channel! Your suggestion worked perfectly and I now have a working heater in my NIVA! 😀

    • @PLUKI4x4
      @PLUKI4x4 3 หลายเดือนก่อน

      That is awsome! Glad I can help 🤗

  • @sahra778
    @sahra778 3 หลายเดือนก่อน

    keep up bro love you from algeria 😍

    • @PLUKI4x4
      @PLUKI4x4 3 หลายเดือนก่อน

      Thank you bro!!

  • @lucijanwitchunter8685
    @lucijanwitchunter8685 4 หลายเดือนก่อน

    Samo gas 💪👍

    • @PLUKI4x4
      @PLUKI4x4 4 หลายเดือนก่อน

      💪💪

  • @brentjoubert-fr1tu
    @brentjoubert-fr1tu 4 หลายเดือนก่อน

    This is going to be my weekend job. Not the heater core, I hope, but the heater valve and piping under the bonnet... Thank you for this channel!

    • @PLUKI4x4
      @PLUKI4x4 4 หลายเดือนก่อน

      Dude, thank you! Wish you a good luck!!

  • @budgey99
    @budgey99 4 หลายเดือนก่อน

    Hi. Great job! Could you tell me what wheel and tyre size you are running? Are those wheels a different offset to std?

    • @PLUKI4x4
      @PLUKI4x4 4 หลายเดือนก่อน

      Thank you! I had those wheels but I sold them, tyres was BFGoodrich Mud Terrain TA KM2 215/75 R15 and rims from kia sportage. I never new what offset they are but fitment was pretty good but a little of scraping if lada isnt lifted

  • @DW95165
    @DW95165 4 หลายเดือนก่อน

    Thank you for this great video and all your other videos! It helps me a lot with my own Niva. Thanks!

    • @PLUKI4x4
      @PLUKI4x4 4 หลายเดือนก่อน

      Glad I can help🤗