วีดีโอ

Thank you for such a thorough video!

Could have been the ac coil!

Maybe you can consider inserting spark plug seals in wrong way. I think more spongy side have to face to cam and more flat side face valve cover.

is it ok to replace the filter on these cars? or should i just leave it alone

If you buy new valve covers, the front comes with a new PCV valve installed, and both have tube seals pre installed. (2005-2008 Acura RL front: 12310-RJA-000, rear: 12320-rja-000

I clicked on the link in your video to order the adapter and it’s currently not available on Amazon is there anywhere else I can get the part from

But what was the symptoms of a bad ignition switch? Everyone tells us how to test it with a special tool, but nobody ever tells us the symptoms of a bad switch. I have a no start no click problem. I suspect it is the switch,but am finding it impossible to find answers, except for going out and buying the test tool to check all the wires etc. Thanks for any answers!

Where did you find the emulator? I can't find a supplier.

Nice information about how to test AC, Have the same problem

150k miles first drain and fill. On that second fill did you leave car running?

Nice job!)

I have that DeWalt saw, I upgraded to a 16-inch bar. The factory 12" bar is useless. When my 16-inch chain wears out, I am going to buy a new 18" bar and a 18" chain. That DeWalt Saw is great for de-limbing trees.

Posted this comment originally to a different video...most of the information is still valid...this is a horrible job so I hope this and the above video help. it can be done. I just finished this Job - 6.5 hour job over 2 days including the time to run to Home Depot. (you need a 17 and 19 MM wrench) I could probably do it in 3 hours now. This video is great help...However these are things I wish I knew as well. Watch the video First and then add this info to your plan. Again carefully watch the whole video IT will save you time in the end. Don't skim! MOST IMPORTANT - Don't buy the cheapest new steering hose. I did and it cause me hours of frustration because it was kinked. Here is the thing you need to make sure about your new hose. Look at the Rack end of the new hose. The last 4 inches should be perfectly straight, and the nut/fitting should spin freely. Mine was kinked slightly and the nut turned but lightly grabbed. Cause me hell and probably an hour and half when trying to get it threaded correctly. 1) If you have smaller hands, you can do this from the top. DO THE FOLLOWING to remove the hose a) Remove the Air Intake hose. b) Use two thick moving blankets folded into 4 layers so 8 layers total and lay on top of engine - protects you and make more comfortable. c) Remove the return line with a 17mm wrench. I did not do this originally...I ended up having to later. Should have done it from the beginning...would have save me LOTS OF TIME AND FRUSTRATION. DO IT First. d) Use a cutting tool and cut the hose right by the Rack fitting. I used an Oscillating Muti-Tool, it cut the line in 2 seconds. Then I used 19MM socket to easily remove the fitting from the Rack. You can use a 19mm wrench...but is a waste of time 2) Follow the direction from the rest of the video to remove the rest of the hose. If you cannot get the 10mm bolts holding the line on the bottom. Cut them with a Multi-tool. I did get the 10mm nuts off but was never able to reuse them. I ended up zip tying. Save your frustration and cut them loose if they don't come off easy. 3) I did take the passenger tire off and pulled the hose out the side. I reinstalled from there as well. 4) IMPORTANT WHEN RE INSTALLING. - push the new hose in from the passenger tire SIDE DO NOT THREAD THE OTHER END OF THE HOSE UP TO THE PUMP YET. YOU WANT THE PIPE TO BE "FLEXABLE" TO HELP YOU LINE UP THE RACK FITTING. 5) GET A HELPER FOR THIS PART! with someone holding the hose by the passenger tire have them help you push and wiggle the hose, so it lines up with the rack. As you work from the top with a 19mm wrench or with your fingers tighten the fitting into the rack. Having the helper make sure there is no binding on the fitting hopefully will make it easy to get the fitting thread started. FYI Mine was more than 8 rotations. 6 wrench turns per rotation - more than 48 wrench turns. Be patient or take a break. 6) Attaching the return line for me was easy - just took a little time as you again had more than 50 wrench turns. 7) follow the directions from the video to attach the pump side, secure the hose, attach electrical connector. I hope this helps some of you. These are things I would have wanted to know in addition to the video. ~Mark

Hi Thanks for video. Is 17 corolla required radio security code after reconnecting battery¿

awesome!! Now i know where the adjustment bolt is. I am going to change the belt 2morrow

well done my friend

Was the cvt overfilled?, it seems like 1/2 quart coming out of the fill plug seems excessive. good video

The two hoses connecting to condenser are what hoses? The discharge and what?

Where are you located I need my ac repairs done

Man, I feel what you're sayin'. I have a sip of my cold coffee every time I got one bolt out, specially because my hands and fingers are fat. You're a good man. Keep your videos out there. Lots of dummies like me appreciate it very much!😅👍👍

Thank you. 😊

I'm going to be doing the same thing I'm going to open up the rear tail lights to make sure that that wire that's down in the trailer hitch is there and the connection is there going from right side and then from the left side down into the trailer I just replaced the plug in the back but the wire that feeds it I'm going to check it at the tail lights

Thank you. I have the same model and for the last several weeks, when the power went out (even for a moment in a storm) everything shut off and I get the fail tone. Today, the battery side stopped working altogether. I've managed to get the essentials onto the surge-only side (no worse off than they would be otherwise) but I was apprehensive about spending $150 to replace the unit. $43 sounds much better, though I'm a little apprehensive about the swap - if I mess up it could be a lot more costly. Thanks for this video, it will help me get it fixed!

Bought some metal pulleys off Ebay. Watched your video several times, till I felt comfortable doing this project. Wife came out and helped some also. Got it done in 50 minutes. And I'm NO mechanic by any means. Wife said it probably saved us a bunch of money.

Do you have to evacuate the freon? And replace it?

Where did you get those red car ramps? They seem like they would be a nice addition to my garage.

What is the size is 10

Hey.., did you find out what the noise coming from the vents (8:10) ? I have the same issue in my outback ;-). Thank you 🙏

Great vid thanks

Is there a certain transmission fluid temperature to check or fill it to correct level?

What kinda lift is that?

Best upgrade ever!! Original design is worst ever!!!

if ya'll getting the code again after replacing the sensor, inspect your muffler/catalytic post bracket weldings, if its cracked that's your problem.

Is the car on while u do this ?

I noticed you said replace the exact amount of fluid but what if mine is very low/empty ? 🥲 How much would I put in it

Thanks for the info.

How it’s holding with that trans fluid brand??

Extremely helpful video!! Thank you!!

Did you put anything on the gasket to make it stay? Does the gasket go a certain way?

well, it turns out that was not the problem. The switch was good but there was a plastic piece bout the size of a coin called the plunger that the switch pushes up against. without it your brake lights will stay on.

Thank video charing...very good

Bruh

Thanks for the video! I'm looking forward to my radio upgrade on my 06 outback!

Great video. Well done

Hey man, I have a 2007 Toyota Camry hybrid after I replace the battery and put the orange safe and I went to the car to start it up but it didn’t. It shows lights on but not on and I make sure the orange key is on. It’s in the proper place, so any idea?

kool, very helpful. Thans for the video I'll find if thats the problem.

hello i have a questions..is Thinkpad T470S support 2nd ssd storage?

Thank you for the video!

Joe biden sent me here.

Brake cleaner might be a bit aggressive for coils and rubber. I'd use electrical contact cleaner.