วีดีโอ

Igen, megfelelő adagolással.

Hi, Glad to hear. Please order from here:lorobbees.com/

Such as?

Üdv Gábor. Jól értem hogy az InstantVap szublimáló hőmérséklete néha felszalad magasra? Ez akkor történik ha a hőmérséklet érzékelő a csavar kötésnél fellazult. természetesen garancián belül megjavítjuk ha felveszi velem a kapcsolatot.

@@instantvap5808 ez Provap 18, amilyet már nem árul. De köszönöm a javítási tanácsadást 🙏🙂 mindig jó, ha szakemberrel beszél az ember, mert kapásból tudja, hogy mi a probléma és mi a teendő.

I came up with this cleaning idea later on. I am always thinking how to improve the unit.

Hi Thomas! Thanks for the feedback, it means a lot to me.

I just hope you will sell thousands and thousands...you deserve it..!!..

you need about 25ah.

@instantvap5808 Thanks for your answer. Allow me one more question. How many batteries can I buy for 25 Ah?

You can buy 3x8Ah, 4x6Ah, etc. I siggest that one battery is not bigger than 9Ah. @@Beekeeper1980

This is not a fix, but an accessory. The tool works fine without it, but it is even better with it. If you feel like, you order it, if not, no problem. Also, it had to be designed, I had to pay tooling 2x, and it is not just any silicone, but a special type able to operate at 300 degrees celsius.

Hello, What I recommend: If the device is cold, you can: carefully pour water into the tube where the dispenser would go, and fill it until you either see it fill up, or until you see clear water flowing through the brass outlet pipe. Care must be taken not to get water around the tube, just into it, otherwise the machine's insulation will get wet and it won't work! You should be aware that there is a steam drain pipe inside the kettle (if you look carefully, you can see towards the front of the bowl, inside), so it is natural that water cannot flow out of the outlet pipe unless the cup is overfilled over the top of the inner pipe. If you see that the water is flowing freely through the outlet pipe, i.e. it is not clogged, turn the appliance upside down so that the pipe where the dispenser is normally placed is pointing downwards. The water will flow out of the bowl, and only a little will remain. Then when you heat it up with the battery, the remaining little bit of water will boil out of it. Anyway, if it clogs, the quickest way to clear it is to heat the outlet brass tube with a gas torch, and it will spit out the clog.

@@instantvap5808 Thank you, i will give it a try again today.

I have tried the following: - cold machine + water pour + heat up the residue - hot machine + a bit of water - heating brass pipe with blow torch If i try with oxalic acid smoke is coming out really slowly instead of "shooting out" as it used to. Is there anything else i can try besides opening the machine and trying to clear the blockage? I am not sure what went wrong, i used the machine according to the instructions, is it possible that it clogged up because we have to use Api Bioxal in EU? I have order those sillicone caps for cleaning to give it a try. I really liked the machine so if it wont work i will probably end up ordering another one just to rule out my mistake. :) Any other tips on unclogging the machine i have would be highly appreciated. Maybe i can use some cleaning agent when the machine is cold?

@@Smradac Hi, the problem is that Apibioxal have additional ingredients, like glucose, and that creates a caramell, and that insulates the bowl inside. That apibioxal product is designed for dripping treatment, and although it writes also on the label vaporization too, it does not work, because you would need to clean the cup every time you vaporize. So I suggets you to buy pure oxalic axcid dyhydrate, and it will work fine. Abowe 99,5% purity. You neds to clean well the inside, remove most of the caramell, and wash it out with sandish style paper or material. You may need to remove the top lid, (4 screws), if you have alan key. You to be carefull not to get wet the rest of the tool, because the insulation around the bowl must not get wet.

@@instantvap5808 Thanks. I have managed to open and clean the device yesterday. I will show you picture what it looked like on the inside (just for the information) :) I don`t know what i`ll do now. In Slovenia in ecological beekeping we are required by law to use Apibioxal. I need to perform some tests to see how fast it clogs ups. If i remember correctly i did about 20 treatments before it started having issues. Maybe i`ll buy another device, so i can do my whole yard and then clean them thorougly. Thank you for your help i need to start nagging to our government now to approve some different kind of oxalic acid :D

Hi. Everything is set up, set to 230 degrees celsius, or 445 degrees F, and ready to go.

Hi. Between 230 and 240 degrees Celsius.

@@instantvap5808 thankyou

Yes, it is in the instructions, because not everyone buys the washing silicone cap. Without the silicone wash cap I don't recommend washing above 100 degrees because it is an accident hazard. The steam will backfire through the dispensing tube and can cause burns. The silicone cap seals and therefore steam comes out through the outlet tube. When hot, around 200 degrees Celsius, the steam is better at dissolving the slag deposited inside the bowl.

@@instantvap5808 thank you so much.

Aux États-Unis, pour une raison ou une autre, ils utilisent des quantités plus importantes, principalement 4g. Je pense que 2, amx 3 g sont suffisants.

oui, cela fonctionne avec la batterie Makita LXT. Choisissez cette option. La température optimale est de 230-240 degrés Celsius. Il y a beaucoup de vidéos en place, même en français. www.instantvap.eu

@@instantvap5808 merci beaucoup

In US, it is set in degrees Fahrenheit, in Europe to degrees Celsius. 230 degrees Celsius is 445 degrees Fahrenheit. Do for not change 445.

Hi. The problem is that yours is too dry. Do you try to use Apibioxal? It is much better to use pure oxalic acid dyhidrate, at least 99.6% pure. . If you keep the OA box a bit open (at least some hours), it will pick up some humidity, and will remain in the tube when you plunge. BR, Janos

Vous pouvez traiter environ 60 ruches avec 2g.

@@janosf7992 merci 👍👍

Provap 18V 👌👍 60000 hft. Ez drága és nemjó.

Hi. It is true, because not everyone purchase the cup. Without the cup it is dangerous to wash it when it is hotter then boiling temperature. The steam is hot, and can shoot back to the face of the person through the feeding tube. This is how you can clean the device with the heat resistant silicone cup: How to use: - make sure the appliance is not clogged! - wear suitable protective equipment: gloves and mask! Oxalic acid vapour still escapes during the cleaning! Caution, risk of burns! - Switch off the appliance after use, but leave the battery connected. - wait until the appliance cools down to about 200°C / 400F. - remove the oxalic acid dispenser. - fill the silicone cap half full with distilled water, then turn the unit upside down and press the silicone cap firmly onto the dispenser tube. - keep the silicone cap firmly pressed down and turn the appliance upside down. - repeat the above.

@InstantVap that makes perfect sense thank you for clearing that up

Hi. Here, it is on stock: lorobbees.com/collections/all/products/instantvap-quickclean-caps

Good point.

bought mine from europe. you can also buy from states.

@@rickabrams3422 thank you

Witam czy ktoś ma polską wersję ? .

The 18V version requires 1.1Ah energy to heat up the furnace, after which 1Ah provides enough power for 9-12 two-gram treatments (depending of the ambient temperarture). There are many type of batterries with different Ah. Some are 2Ah, others 4-5-6-9-etc. With this information you can calculate.

Hi. Unfortunately, only 18V version, from Bosch the Procore and GBA. If I would use 14V battery, the current would need to be very high. You can see all the socket options on the web shop: www.instantvap.eu/

Hi. if you consider that you have to buy a generator, cords, petrol, and all the hassle, the picture may be better. Also, people usually manage to treat with InstantVap their hives in half the time compared to corded version. If using 2 tools / person in commercial beekeeping, you can treat one hives in 15 sec / 2g. But I understand that if someone has only some hives, and already set up for the corded vaporizer, it sounds pricy.

@@instantvap5808 you are sure, that 15 sek will help bees? can we see any test results please!

@@olenormaalne6409 Hi. Yes, I did a lot of experiment, and it works. Mite drop is amazing. You can also check out this video where someone do mite wash after.: th-cam.com/video/-Mz3YmcPGjU/w-d-xo.html

There is a much cheaper and faster sublimator. Provap Rapid 18.

It takes about 20-25 sec / 2g. It is about 160-180 degreees. It does not kill brood.