วีดีโอ

Drum brakes were designed by Satan

Very nice and informative video. Small tip on tightening the servo saver: I also upgraded to a metal tooth 35kg DS servo, so I tightened the servo saver thinking along the same logic as you, that metal gears won't strip. While that is true, immediately after installing the servo saver I broke both left and right steering knuckles on the same day. The right side broke during an impact while I was also steering, the left broke just driving next to a pavement. I think the wheels being in a situation where they can NOT move, if the servo saver is too tight, the upgraded servo actually has enough force to break the steering knuckles. I now set the saver a bit looser, but not as loose as factory, so now it has some play if I grab the wheels tight, didn't break anything since, fingers crossed. Looks like the play in the servo saver can save not just the servo gears but also the steering assembly in cases of impact or when the wheels are stuck.

I just tried to use these on my Tundra. One arm broke at the hinge.

Today I was working on this same machine and the owner never had it serviced since they got it in 2017 😅. The problem they were having is the tank keeps overfilling and shoots out water from the safety valve . The only thing I could thing of causing that was the water level probe at the top and I took it out and cleaned it with some sand paper and it resolved the issue . Should I replace it to a new one or just work it so for a while? Also the solenoid on the group heads and valves were completely shut , had to remove the whole head and delime it 😅. Got back one group head to work on the left the right one needs a solenoid . Orrrr what I noticed when I was pulling my shot is that the little drain pan starts to fill up with water while I’m pulling a shot & starts to overflow. Do you have any idea as to what can cause that ?

Seems slower than a sand blaster.

Hello there Gregs Lair, I was just about to open a manual on that machine, came online and found you wow, i already appreciate this video. My machine has no pressure at the brew heads and the water isn't as hot on one side , the steamer and hot water work perfectly, I opened and clean the brew head system which made a little difference so now watching you i may have to check the heating element. so far i realized the solenoid valves at the brew heads mya be defective but need to check all other aspects of that issue. Thank you so much for that video.

Did you rvrn read the directions? You certainly didn't follow them

I bought two of them while on sale for $29 each. One of my better investments. They work. Forget about the scale. Set it with you caliper. By the way press the button and use only one wrench.

Have you sold it yet?

you need to know the difference between a cylinder and a head

I like the look of the Suzuki. I have the Xpect and that is a great bike for the price. Great bike with free shipping. Mine came the same way and put a few things on.

Beyond Trailer-park Ghetto

The $50 brasilia espresso machine gauge fits these machines with the rectangular face. I'm having an issue where it's healing behind the group head and won't build any pressure too make shots. I think the pump is fucked

The crunching/munching sounds are top tier <3

Update on this router? Do you still use it and is everything ok?

you will have better luck if you keep the suction line that is going to the nozzle on the top side of your wand that is what my instruction say to do, good luck !

is it possible that the black hole are black dye use to convert the white ekopel to a gray that were not properly mixed at the factory ?

Curious and how long did the thing lasted you?

Thank you so much. My BBQ aluminum handle broke off and I needed a way to weld the two pieces back, I went and purchased this on 6/27 wish me luck.

Hey Greg still have the van van 200 & Lifan motorcycles. You have not made video of them in a long time.

Run a magnet to recover the baffle screw

Bowel gasket on carb hard as plastic and it leaks, and is corroded bottom bowel. After market carb fine with me as I already thinking different kind of air filter. Do they sell a left side cover gasket? I was thinking of making one but the time to cut one out, eBay? Thanks for your help.

Thanks, i just got through removing rear wheel that the brakes were corroded to the drum and upon removeble pads cam off aluminum part of brakes. I can clean them up and maybe jb weld them back on. Wheel was locked up. Now cleaning left side cover thinking to make new gasket if i find gasket paper long enough. What kind of oil in left side gear box. Oh update; i started it up with premix and i ran it just alittle because no oil in left side gear box. Carbuerator was corroded and now leaks, any luck with carb from e-bay or amazon cheapy ones? They worked great on my weed whackers.

Why do you think the pump goes bad? I took it completely apart, cleaned it, no sighns of any wear. And i did tbis like 4-times and still dont work. Im gonna try what you did with mix in the tank and run it and see if that will make it work. With pump out i attached a drill and ran that and not a spurt. Like i said i try what you did and if that dont work ill use my weed whacker chainsaw mix.

You ran it that long without oilmix😳

I drilled new mounting holes for the shock in the top bracket (moving it higher up and more forward). It dropped the seat height about 1 inch and seemed to make it handle a little better too.

I noticed you have an 18" chainsaw. You can use this to quickly measure 18" when making 18" cuts; just turn it so it is parallel to the log and note the distance from the end of the log to the end of the bar.

Dude hurry the hell up, Nobody wants to sit here and watch you take your time talking. People got things to do. “Here’s the Suzuki im working on’ DURP

Hearing protection?

I adapted my Bosh MR23EVS plunge base to the Milescraft base plate by adding two more screw holes of my own and it works fine. It can also works with the Dewalt plunge base.

Why would you even post such a pathetic video. Your wiring skills suck

I think Dale is right about the feral being missing

Enjoyed the video, also that Shinner Bock

Do you like this saw?

Great video thank you. Dale sent me.

Positive battery cable goes on first ground second and the opposite for removal!

What size sand?

what happens if i leave the oil injection on the bike and just start using a pre-mix???thanks

good video,i do have one, i was wondering if i could put a tubeless tires in it?

Инструкция как делать не нужно. Спасибо за видео, все понятно.

I don't think I will let you do my wiring

Here is the manual with all of the parts shown in diagram. chrome-extension://efaidnbmnnnibpcajpcglclefindmkaj/manuals.harborfreight.com/manuals/67000-67999/67090.pdf

If you would put a little effort into a video editor you could eliminate all of those spots where you've wandered off and the viewer is just left staring at his screen. When you 1st went looking for a piece of wood to split in the beginning I thought I had accidentally hit "pause". Like the mod for the wheels, though. I've had one for about a year. Works great. Haven't used it too much, but now the high pressure valve is leaking. I came across a manual for these and it has an exploded schematic with all of the parts numbered. I might get a new seal and try to put it in.

I like that you did it in real time to give an idea how long it will take. Thanks for the info!

Damn Honda has front pads and rear drums. I can change pads in 20 mins... took me 4 hours for those 2 "HE-MAN" springs. Cruel bastards

My question is I put a brand new oil pump on mine the only reason why it was puking oil all through the cylinder head following the plug horribly. But I'm still having the same issue. Trying to troubleshoot this anything that you can tell me would be helpful thank you. Its a 77. NC 50

Any way to adjust oil pump to accommodate a 70cc big bore kit

Great video and so nice to see how nicely you responded to everyone. May the Lord Jesus Christ bless you and your family

Hey much much did they charge you for full assembly?

I bought a new 1965 Yamaha Riverside 55 and it had a turn signal switch but did not have the lights installed. There were rubber plugs in the mounting holes on the frame and fork for the signal lights. Back then I heard that they didn't install them in states that did not require signal lights. True or not about the state law? I don't know. My brothers 1963 Yamaha 80, like this video shows, had signal lights and in the same state. Who knows????