วีดีโอ

bugger this charger appears to be discontinued. In this boat now needing to try get some prius modules back in action, or at least diagnose the bad ones.

Nobody cares about all what you paid for the chargers and how many miles the car had. How did you hook all this up. I see you have 15 and 25 volt versions. Are they for 2 and 3 module packs? No clue what you're doing.

2:01, counting cells? What's the reason you asked that? Interesting.

How long does this 3 phase cycle take?

Modules should never be charged/discharged out of the rigid fram in the HV pack. This is to avoid distorting the module.

wow good i need to buy imax b6 for repair cell battery prius same you Thank

Was the b6 calibrated before charging ( another video said that was needed) ?

This stuff failed. Nothing came up.

CAN YOU SHOW HOW TO CHARGE 2 OF THESE WITH THE SAME CHARGER OR B6AC

Thank you Tommy now I see what product I will buy and give a try. This video helped a bunch.

i just bought a kit in green.. they look so beautiful

I recommend standing UP and using a FLOOR SCRAPER!

Hi Tommy, We would love to share this video with our customers! May we share it? Great Build.

Great Video!!

Hello sr. Can you Share the settings on chargers that are a little stronger. On charge and discharge

If its 4.56 gears and you have at least 28 inch tires, you should be doing over 100 if you have it tached up to 4000 rpm.

I recommend Blue Bear 500MR. It's made from soy beans, has a non-offensive citrus scent, and works great. Spray or pour it on, let it sit for a couple of hours (adding more if it dries out), then using a long-handled squeegee or scraper, push the liquid mastic into a pile of clay-based kitty litter, and scoop the litter into garbage bags. Finally, rinse with a bucket of water and TSP.

Does the charge reaching 9.0 volts have to hold for a specific time to be considered charged up or can we manually hit discharge as soon as it reaches the 9.0 volts?

Any recommendations on gluing vinyl for wooden floor?

thanks for the review!!

Hello with these setting on my first module I tried i get my module a little bit inflated. I see some people holding the module squeesed between to pieces of wood... If i squweeze it now it returns to its original size... Do i have to throw it? ... I set charge in auto 5.0 Amp like in the video and i observed 5 amps while charging, I expected 1 or 2 amp adjusting automatically but was 5 amp all the time... Maybe should I limit it to 2 amp charge? Thanks in advantadge

Hello with these setting on my first module i tried i get my module a little bit inflated. I see some people holding the module squeesed between to pieces of wood... If i squweeze it now it returns to its original size... Do i have to throw it? ... I set charge in auto 5.0 Amp like in the video and i observed 5 amps while charging, I expected 1 or 2 amp adjusting automatically but was 5 amp all the time... Maybe should I limit it to 2 amp charge?

I bought the same brand for 2nd gen Camaro but more of a project to assemble. For smaller gauges I chose bar sequence type not used to numbers display. I too aught to post.

Does it still runs and drives?

Thanks!!!

I'm using a tenergy t180 on my 07 camry hybrid, i let it sit overnight but it cut off at 240 minutes for safety timer, and my capacity cutoff was set at 6500 but when i checked the screen, it went above that but it didnt shut off the charger, is that normal? or am i doing something wrong?

I’m dealing with a similar challenge in my 63 Nova. 327 & a TH350. I don’t know for certain what’s in the differential, but from the factory (and it’s an original axle, of that I’m certain) it had a 3.08, and I know it’s not posi or LSD. - it leaves 1s, not 11s. The engine is strong and trans shifts smoothly, but in 3rd (top), I’m turning 4200rpm at 70mph. Also power seems to drop off around 3600-3800. I recently put a new carb on (Holley 1460 600cfm, as the old Carter was shot), so it could be jets. And there’s no mark/strip on the balancer, so I can’t check timing, but again, she starts easily and runs well until I start pushing her. Top speed right now (“Captain, I’m givin’ her all she’s got!”) is about 77-78mph.

Cool

Why you do me like this 😆

How do you program a dash like this

Dude, you got major respect from the gate. Love the jacket.

I have a 1995 Chevy C1500, 5.7 that has recently installed a Intellirtonix guage cluster. Each of the guage said are working fine with the exception of the Speedometer calibration indicator constantly reads, "Erorr!" Any suggestions?

4.56s are SHORT gears, not “tall”.

Can I charge two cells at the same time with another cables?? Or only one at a time??

? I see you programmed it to stop at discharge 6 V. Is there a way to set this charge at 7.9.

I bought Intellitronix gauges for my truck only half worked after alot of phone calls they sent me another set all worked buy one it cost me $600 to have them installed and then taken out reinstalled the new ones that still didnt all work .took them to court and won! ended up buying Dakota digital they work great and are alot nicer looking

People also ask Is HobbyKing legit? They are a cheap China direct RC seller. You are not going to get ANY customer service. You are going to wait upwards of a month for your stuff to arrive. Some of it may be DOA, and customer service will only give you store credit.

Hi Tommy. Perfect video ! I use the same reactor with 240 W. But one question: Some modules blow up a bit, and other like a balllon. When are bloating modules not okay for you?

good video I bought a cluster but I lost the instructions you can send me a copy

good video you will have a copy of the instructions buy one and I lost it

Yikes! I thought for sure he was going to say “our number 1 priority right now is... to do it safely and assume it does has asbestos.”

Hey tommy how did you balance them and with what settings? I have a T180 turnegy

Can you tell me what's the discharge minimum v.

Rpm guage is won't. It's got a switch on the inside to change it between ls and v8 might have it in the wrong position

Your subscriber would go up so much faster if you just focused on reconditioning hybrid batteries. This information is a necessity nowadays

Hi, if I set it to 3 cycles of discharge and charge with 5 min wait time , will it do it automatically cycle or do i have to push start again? Mine was set for 5 min and its been like 25 min after its done with discharging and its not charging back? Should I be pushing start again??

Put 35" tires on it and your gear ratio would be fine

Hii Can you recommend me where can i get this type of chargers

Hi..🙂 Where can i get this charger sir.. Can u recommend me

Please wear a mask. 8-)