วีดีโอ

This is a nice video. Can you send me the link where you buy that one?

Would it fit a mt100 ?

I got one getting nitrogen tank next week. Getting it ready I put a good bit of grease in it and not seeing any coming out. Does it suppose to come out bottom?

I'm looking at one like you got with post driver, how has yours held up?

Actually a good video telling people to think outside the box. I'm an electrician and will use tools in an unconventional way like this. I havent done this with the super hawg before though. Only advice I have is keep chin away! I saw 2 different accidents with guys using them. 1st one was plumber who split chin open and 2nd was electrician whose glove got caught in chuck. It broke arm bone out through skin.

I have a CAT 299 ex and i bought a Bobcat rake that I've had for over one year and it has a smaller harness with a 7 pin connector that I can't use. I need a 14 pin connector. Bobcat won't help me because I have a CAT and not a bobcat. $1600 later, here it sits. Any suggestions on putting this to work?

You 100% should have a T handle atleast 1" wider than the pipe this way no possible way to accidently drop the pump and or pitless adapter when installing

Thanks bro , im doing mine tomorrow

what about the Check Valve on top of the pump

thank you man old days every thing was kept to themselves . i know your business will prosper because your a honest descent man keep doing what your doing and dont look back

Big Question: Where did you get your nitrogen tank charged? I can't find any place that charges Chinese tanks.

Why doesn’t Lowrance fix the problem glad I went with a quest

You guys with heavy equipment and make content on u-tube need put a switch on the back up beeper so you can turn it off because it very annoying 😑 🙄

Is this the 60" or 72" CID?

U Da MAN ! 👍👍👍

Really nice video! Thank you. 🙏🏼

Hello so when you remove the gauge after filling does any gas come out or only if you were to push the button? Great video thanks for the help.

kind of a dumb question, but howd you get the electrical tape off the pitless adapter? just yanked it off?

Yeh cause everyone has an air compressor at home

Nice video but the after like how well the grass comes up would be good

Do you also have to charge the high-pressure side to 853 psi?

Thanks for the video, just got a 317 this week and within a few hours I noticed the air flow decreasing. cleaned the cab filter but did not know about the outside one.

Thanks man would love to see more

How do these do with rocky ground?

Just bought one for my mini excavator, only gave 600 for it. I was wondering how to put the gas in it, thanks for showing me.

Crocks with socks!

OK what happened at 20 seconds

Sweet video! Whats your rate to do this kind of work? Looking to buy a 333g and similar mower. Thanks

My buddy bought a new boat nd offered his old one to me for a decent price. So i sold mine ...it had the minnkota ultrex with garmin echomaps and livescope. His that he sold me has this peice of crap lowrance ghost,elite 9 with active target. Im so pissed .im definetly going to get the addon pointer that attaches to the shaft at the water line and get another garmin unit and livescope and sell this crap ass lowrance unit amd acticlve target..if i can get a decent price for the ghost i will.sell it.also and get another ultrex..smfh

Thank you for being the guinea pig for us.definetly appreciate it. I also dabbed a little bit of glue on backside of magnet on the pointer and glued the washer that it sits on to the clear cover between the 2 magnets..im going to apply a little vaseline where you put the grease

Good video you need a check valve at the pump

Niccccce

What do you charge by square feet to aerate?

Doesn’t work good as an auger!!

Many Municipalities require the well head to be 18" above grade to prevent surface water contamination (from rain and flooding) cutting below grade is a no no.

I really enjoyed your video. Starting to research different Harley rakes. What brand and model of Harley rake are you using in the video. I also have a JD 325G Thanks

Thank you!

This track tensioning system is an absolute shit design! Absolutely not field friendly, and requires shiting grease everywhere, and specialized tools.

Great video, could you tell me what HP pump you guys used. thanks

What did you use for the adapter from drill to bit?

It’s glyphosate. Not glysophate. ✌️

Great Job Explaing ...

We spend all that money, we shouldn’t have to do anything to them. But it seems what you did worked.

Did you need any other attachments or pieces to use the Super Hoag with that auger bit?

I'm in the desert, 25 miles from Home Depot. Added some sprinkler heads to my irrigation system. A big rock crashed into my sprinkler valve manifold and broke one of the pipes. I would have had to rebuild the whole thing, and I didn't have the parts. I also didn't have the right size hole saw, BUT, I had the right size deep socket. It worked great with a screw driver to get started and needle nose pliers to twist it out. Saved me a bunch of time, gas and money. Thanks for sharing!!

Very cool dude

I love our SK. Best piece of equipment we’ve ever bought.

Awesome job on the video! Thank you so much, this was exactly what I was searching for.

Good video but you should be careful touching weeds that are sprayed with herbicide.

I'm up tonight watching you cut..