- 16
- 12 364
CraigD
United Kingdom
เข้าร่วมเมื่อ 28 ก.ย. 2007
วีดีโอ
Start Lights system I made For Our Rc car Club, With Lap timer and False Start.
มุมมอง 1514 ปีที่แล้ว
This is My start light system I made up for our club, I ended up adding a lap timer as you can see. ( its crude but works). It does make it so much more fun as every one is so competitive lol.
Slow Motion Rc car Hyper7, Samsung S20
มุมมอง 414 ปีที่แล้ว
A short video of my Hyper 7 in dirt. I was just testing out my new Phone Samsung S20
HOTA D6 Pro duo Lipo charger Faulty Channel .
มุมมอง 5K4 ปีที่แล้ว
Channel 1 would not charge. After stripping it down and testing it, I found a fuse had blown on the pcb. Once I replaced it it worked fine🙂.
Xt90 Connector soldering Rc car Lipo
มุมมอง 1364 ปีที่แล้ว
Had to change a Dean to an Xt90 Connector for a friend, this is what I found under the tape. It could have broken off then possibly shorted the lipo out.
Lipo Balance leads made Extra long so I can charge it in my Ammo box.
มุมมอง 384 ปีที่แล้ว
These are my extra long leads made up for my charger to lipo, so it will reach inside my Ammo box for safer charging.
Basic Soldering Tips. Rc World Tip cleaning and tools
มุมมอง 594 ปีที่แล้ว
Hope this video helps you gain the basics about soldering, the more you do the easier it gets. Get the right tools and that is you half way there.
KARCHER 380 jet wash is dead.
มุมมอง 1.9K4 ปีที่แล้ว
Karcher 380 jet wash does not work. So after finding the fault it was an easy fix.
Mountain Bike (MTB) rear Gears slipping Sunrun gears.
มุมมอง 1.1K4 ปีที่แล้ว
Rear Gears Lose, all bearing have dropped out too.
HoBao Hyper7 Brushless Conversion, Video done on a Samsung S20
มุมมอง 764 ปีที่แล้ว
Brushless conversion from Pbs.
F-16 Jet with Rear mounted camera
มุมมอง 62516 ปีที่แล้ว
F-16 Jet phase 3 with a Flycamone2 mounted on top.
RC Helicopter, belt cp with onboard camera
มุมมอง 89216 ปีที่แล้ว
belt cp helicopter with a flycamone2 mounted under it
Brshless Helicopter, Belt cp first flight.
มุมมอง 53517 ปีที่แล้ว
Brshless Helicopter, Belt cp first flight.
Thank you - I was wondering where the other screws were ;)
hi, my d6 pro just died today, it smelled something fried inside but the charger is working if on dc mode, can you help me fix it? i was just using storage mode on using AC..
What amp rating did you get for the fuse? 15 amp?
Hi, I went with 10amp to be safe but I believe its rated to 15amp. Not had a fuse blow yet with 10amp.
bravo!!!
Mine one also shows the same error current operation is not supported and also sometimes abnormal battery connection error message but it reads the Voltage and also from balance leads too , do you think it's the same problem?
I don't know sorry, if your ok with electronics test the fuses and all the wiring. Worth a try.
I had to reflow the solder on my fuse. Works good again
My Dual Smart Charger just quit when I was plugging in a new Lipo and it’s only 3 months old 😡 Hopefully it’s just a fuse.
thanks for the video, I have a problem with my hota d6 pro, if you don't mind I need a photo of the electrical schematic or photo of the D6 MBV1.0.2 board. thanks
th-cam.com/users/shortsNlFquUblKqY?feature=share
Sorry I don't have that Information, best you contact Hota Directly thanks.
I bought a HOTA D6 Pro that had this problem, opened a complaint on Aliexpress and they refunded me 50% of the amount, since one channel doesn't work. I thought it was my bad luck in the purchase and I bought a second charger just like it, after 3 months of moderate use, the same problem. I do not recommend this charger. It's cute but it sucks and it's going to break soon.
Thank you very much for your video
Anyone found a way to get the fuses? With min amount shipping and handling it's like 20 quid!
www.mouser.co.uk/ProductDetail/Bourns/SF-1206HV15M-2?qs=gTYE2QTfZfSThH7Z0dUJfA%3D%3D a little bit Cheaper Chris.
Are those mosfets? ( under the heatsink ) ?
My hands were wet when I unplugged lipo it popped. So later I try an put my lipos in storage mode it comes on I plug the second lipo it shut off. I’m about to open it up.
Well start with the fuse first as per My video, I'm sure it will fix it. Good luck.
@@Dingmiester I appreciate you taking the time an sharing your knowledge.
Good to know it's fuse protected at all, but I wouldnt exactly call it user serviceable. I have a Hitec RDX1 PRO that suddenly started reading voltage all over the place. With everything unplugged the battery meter fluctuates between 0.1 and 2.5v. It still charges but im sure its ending the charge prematurely.Hopefully Hitec will warranty it.
Its fa from user serviceable but that's how they make money I guess. Lets hope in the future manufactures have the sense to install replicable fuses. Hope you get yours sorted by Hitec.
I am in USA, I have one with 110V, same problem. I have not open it yet, is it going to be the same part? Thx.
Hi, 110v is just the supply it will make no difference. If you have the same issue as per my video its more than lightly your fuse. Hope you get it sorted.
I bought a D6+ just a little more than a year ago from a reputable local hobby store. It's been working great until today, when I started encountering a slightly different problem: it reads the voltage of the battery when I plug it in but when I charge (or any other operation) on that channel, I get that same error message "current operation not supported". the board in mine looks to be identical to the one you have. The same fuse on mine actually shows no resistance (or nothing above the internal resistance of my meter). But the appearance is very suspicious; the fuse is slightly brown and the soldering on that fuse is certainly not neat. I don't know if this got too hot and the solder melted into a blob or if someone tried to fix it at the factory... <edited...I just read through the comments and saw the current rating> 😜 thanks!
Sorry for the very late Reply Robert, Did you have any luck sorting it out. It does sound like its the fuse, did you replace it and is it working now ?.
Hi - yes, I replaced the fuse and it is all working now. I did have some additional issue afterwards where the voltage reading was off by approximatly 1 volt until I plugged in battery balance leads. I tried a few things but ultimatly I resolved it by doing a factory reset. Thanks!
Heinz Longerich Thank You for the information. I bought the same charger and DC works but Ac dos not work there is no screen showing up. Any help ? Heinz
Is there any power to the screen, does it light up at all. First thing I would do is take it apart and see if the wire has unplugged itself first.
@@Dingmiester Only DC it will light up
sf1206hv argggg its not the whole number!! the last 2 numbers needed were the amperage value they blow at. i was going to pre order some but i cant without that info
They are rated at 15 amps .
SF-1206HV15M-2
hey ! just saw your video i think i have the same problem where did you find the fuse ? if you have a link i would be glad to have it ! thank you ;)
Hi, Here is what I used. Not easy to solder as so small. I am going to make a new video and change the fuses in the board to 5x20mm external fuse holders. I think it will be so much better in the long run. uk.farnell.com/bourns/sf-1206hv15m-2/fuse-15a-high-inrush-withstand/dp/2911347RL?st=SF-1206HV15M-2
@@Dingmiester great that would be helpfull ! thank you for your reply !
Any chance you'd be able to do another one? 😉 Happy to pay! haha
Hi, I'm going to look at doing a new video but installing two panel fuse holders. It will be a much easer job and in the long run much easier to change blown fuse in the future .
Excellent tutorial, so we'll explained and demonstrated.
Thanks for the video, it was a great help as I had the same problem,.
Glad it helped.
@@Dingmiester the clear plastic tube what dose that do i have a 380 but can not see what it dose tryed putting it in a bucket of water when running but nothing .
@@margaretkebbell5223 Hi its a Detergent suction hose .
Hello my friend i have this same device and my battery its 450 4s Lipo can you tell me what the good setup for it please thx 🙏
I'm glad I found this video before I bought a replacement. Would you happen to know the amp rating for the fuse model you mentioned as there appears to be quite few ..
I went with 10 amps to be on the safe side. Its rated at 15 amps per channel I do believe. To make it easier you could look at getting a fuse holder rated up to 15 amps and fit it to the side of the case. That would be my next job if it blows again. SF-1206HV15M-2
@@Dingmiester you mean like an automotive blade style fuse and fuse holder ? what gauge wires would you suggest ?
@@TeamBlindMouse Yes that's one sort, I would personally go with a round fuse holder with screw cap, Amazon/ Ebay sell them. It would be easier to drill the holes. Make sure it's rated 15amps.
Cheees mate, all working now
Happy for you Khyle well done.
Nice work! Great information as these age and more people run into this problem. Surely it's a pain to solder that component on, not to mention waiting to get it in the mail. Small tipped iron, steady hands, and a bit of luck must help lol as others have said maybe add some bodge wires and an ANL fuse or something to make it easier to repair in the future :)
I would agree Mitchell, It was not ans easy task as most tips are half the size of the fuse. I think the way forwards is to fit a fuse holder of sorts to the body with long wires soldered in place of the fuse. I may do a video on that soon ..
I just want to fix my bicycle 😭
Great video! #rccars
Love this what did you make the video on?
I did it on my phone using Youcut video editor 👍.
Thanks it was a help
Happy it helped .
Very informative and very helpful
Glad it was helpful!
Good stuff!
Thanks!
Superb mate.
Many thanks!
Great video!
Thanks!
What gyro and motor do you have? BTW whats the name of the first song?