![Tom H](/img/default-banner.jpg)
- 49
- 358 978
Tom H
เข้าร่วมเมื่อ 19 ต.ค. 2013
วีดีโอ
Yaskawa Sigma II Clearing Alarm History
มุมมอง 6752 ปีที่แล้ว
When troubleshooting a servo problem usually the first step is check the alarm on the servo pack. The problem is there are times you may have multiple alarm occur, to be sure I am dealing with the most revellent alarms I always clear the fault history.
Sigma II how to display Motor Information
มุมมอง 7012 ปีที่แล้ว
There will be times when a servo motor begins to have trouble. And most of the time that motor is located in an area that's not easily accessible. With the Sigma you can display the motor information so you check and verify you have a replacement or need to order one.
Automation Direct Deleting Project From a DL-205 PLC
มุมมอง 9364 ปีที่แล้ว
In this video I will Use a 2 step process to Clear the PLC memory and restore it back to factory default. First I will CLEAR ALL then I will Initialize Scratch Pad.
2c Studio 5000 I O Module Filtering
มุมมอง 2K4 ปีที่แล้ว
In this video I show how to apply the filter when selecting I/O modules. this will help narrow down your search.
2b. Studio 5000 Logix Designer Using Auto Discovery To Configure I O
มุมมอง 2.5K4 ปีที่แล้ว
In this video i show how to use the Auto Discovery function to detect installed modules on your system.
5b Studio 5000 Logix Designer Deleteing A Sub Routine
มุมมอง 1.3K4 ปีที่แล้ว
In this project I show how to delete a Sub Routine in Studio 5000 Logix Designer.
6. Studio 5000 Logix Designer Adding A Periodic Task
มุมมอง 2.5K4 ปีที่แล้ว
In today’s project, I will be creating a Periodic Task. I will also discuss how this Periodic Task could be used.
Studio 5000 Checking The Firmware Revision Number Of Controller
มุมมอง 8K4 ปีที่แล้ว
In this video I will use the RSLinx Classic Software to show how to check the Firmware Revision number of the controller.
5 Studio 5000 Logix Designer Adding Sub Routines
มุมมอง 5K4 ปีที่แล้ว
In this project I will be adding a Sub Routine to the Main Program. I also show a common mistake made when adding Sub Routines.
11 Studio 5000 Logix Designer Off Delay Timer
มุมมอง 1.3K4 ปีที่แล้ว
In this video I walk you through programming and the operation of the Off Delay Timer (TOF).
122. Studio 5000 Uploading Project From Splash Screen
มุมมอง 1.9K4 ปีที่แล้ว
In this video I will Upload a project from a 1769-L33ER CompactLogix Controller. I will use From Upload on the splash screen. Update: Now there is one thing I forgot was around the 3:10 mark I saved the file as Test_3a,
2. Adding I O Modules
มุมมอง 4.7K4 ปีที่แล้ว
In this video I will show how to Add I/O Modules to your first project.
1. Starting A New Studio 5000 Logix Designer Project
มุมมอง 11K4 ปีที่แล้ว
In this video I walk through the process of opening a new Designer 5000 Logix Controller Project.
Yaskawa MP2600iec Version Handling Error 1
มุมมอง 6857 ปีที่แล้ว
Yaskawa MP2600iec Version Handling Error 1
Yaskawa Sigma II Clearing Alarm History
มุมมอง 11K7 ปีที่แล้ว
Yaskawa Sigma II Clearing Alarm History
UniDrive SP Changing Rotation Of Motor Using PowerTools Pro
มุมมอง 4.8K7 ปีที่แล้ว
UniDrive SP Changing Rotation Of Motor Using PowerTools Pro
How To Reset A Sigma II Servo Amplifier To Factory Default Settings
มุมมอง 2.5K9 ปีที่แล้ว
How To Reset A Sigma II Servo Amplifier To Factory Default Settings
EZ Touch HMI Convert From Smaller To Larger Display
มุมมอง 13210 ปีที่แล้ว
EZ Touch HMI Convert From Smaller To Larger Display
How To Add Offset To AutoTech Model 1050 Programmable Limit Switch
มุมมอง 59210 ปีที่แล้ว
How To Add Offset To AutoTech Model 1050 Programmable Limit Switch
EZ Touch HMI Converting From A Larger Screen To A Smaller Screen
มุมมอง 34210 ปีที่แล้ว
EZ Touch HMI Converting From A Larger Screen To A Smaller Screen
Hi Tom, Please help me! How to reset AF6 driver fault? Thank you
can u share link of material
hi tom , the program can run with windows 10? we have plc d3-330, d330
Hello Eng. Good morning. Excuse me, I have a fault, it is A.82 on an SGDH-30 AE Drive. Could you help me since I have tried to restart the drive and it does not allow me and marks me as not OP. greetings
Thanks
Hello, i'm a complete beginner at this software and i wonder how you download the ccv change 'cause my pc shows "disable drive" and i didnt find anything to disable it Thanks c:
Good info.. keep posting 📫 😊
L33er i am using 😊 i am new to programming 😢
Pls post video for water treatment plant, 😢
Excellent 👌
I did this but now my motor won't work and just slowly twitches around..
HI Mr Tom i have a question about setting position control pin numbers for SGDP-04APA or pdf manual link i look everywhere with no luck. can you help me out please to find out how to set up?
Can you please give your contact number
Can I contact you
can you add more recipes just from a button on the HMI? or do you already have to add the placeholders for the recipes in the HMI software first?
I have entered multiple recipes but if I remember right? It's a maximum of two hundred tags that you can use for recipes and it's for all the recipes that you will write
Hello Tom, I want to know how to check the PLC program that is running on the Logix5000 PLC is latest or not. I have loaded .acd file on the PLC and its in run mode. I want to confirm if its the latest acd file running how todo this?
Thanks . How to get access to the full playlist of this video ?
can i have that word doc?
Thank You
I shouldn't be here ...
How to fix bb error please ?
Good Morning, .bb is not an error or fault. this is actually called base block. The drive is in two sections LOGICAL & POWER SECTIONS, in .bb the power section is off. Most probable cause is e-stop. Or if the ENABLE signal comes from PLC check the output. Hope This Helps Tom
Hi Tom, i have one yaskawa sgdh 15de-oy in old machine, i have Pot error, i have sensors in the machine, i want to ask you if i follow your procedure and mask Pot error, if i want to go back is it possible ?
cannot resolve, sgd72 error 300. regenerative. Tried resetting but nothing. is it toasted?
Omron a.84??
The A.84 alarm for Sigma 2 Servo is an encoder data error alarm. This alarm is for both absolute and incremental encoders, and its meaning depends on the type of encoder. Absolute encoders At power up encoder is malfunctioning and replacement may be necessary. If this alarm appears during motor operation, it could be caused by external electrical noise. Incremental encoder During operation or at power on (intermittently or static), most commonly system vibration should be examined. Excessive vibration (exceeding motor specifications) Most common causes, - Excessive Mechanical Vibration - Excessive Electrical Noise Hope This Helps Tom
SGDH-01BE HOW TO SOLVE ALARM A.05,
What does the codes A03 and A09 indicates
The create backup file is greyed out on the transfer tool. How do I get it to be selectable?
thank you sooooo much! i have 3 dead procesors, and now all work 100%! thanks!
Hi Tom do you have a facebook account?
Hello Tom Our Yaskawa SGDV showing P-ot N-ot problem and it didn't appear even we restart the servo. thanks
If you are following the procedure the alarm should clear. First I must ask do you still have the P-OT or does the servo pack not go into RUN.
Hello , Am using Yaskawa Servopack 400V, SGDV-1R9D21A. Am getting an error code message as : A.810. How can i reset the alarm ? I would greatly appreciate any help...
In the video that I have posted yasukawa resetting the a. 81 is the same procedure for for the sigma 5 a.810 fault. But sigma 5 and sigma 7 product line can be reset by programming. So check and see if there is reset option the manufacturer may have programed.
@@tomh2466 Thank you for your reply Sir.
Sore mas cara menghilangkan tulisan E HBB dan E Pot gmna ya? Mohon bantuannya mas
How could I progrmatically grab the firmware revision number as a tag into studio 5000? GSV doesn't seem to have this option.
Sir if have code error how to fix
mohd yasin Idris It depends on the alarm. What is the alarm,
Are you going to do any Sigmawin SigmaII tuning videos?
.
What is the difference btween MotionWorks MPE720 and MPE770 software ?
How to upload motion program from PLC ?
How to uplaod motion project from MP2200 ?
Vorapob, To upload project from your MP2200 you will need MPE770 software. And from Yaskawa: "MotionWorks MPE720 software is not a free download and requires a paid license". Contact your local rep to purchase. You could contact Yaskawa maybe they can e-mail you the software. Hope This Helps Tom
@@tomh2466 How can I know IP address of PLC MP2200 ?
How to upload PLC program from MP2200 and motion control for servo ?
My SGDH-01AE drive shows red charge button, but the green led for power is not glowing. Please help!!
The Servo Amplifier is split into 2 sections the Power section & Logic Section. The green LED is for Logic control, check and verify you have power to L1C & L2C. If you do replace Servo Amplifier. Hope This helps Tom
Thank you tom
Hi! We replaced the servo card in an SGDH 50 AE servopack. We want to parameterize PN UN FN numbers. Do you know of a calculator or something where I can find the factory UN PN FN numbers?
Kmetovity Levente, Following this video you will reset all the Servo Pack parameters (PN) back to factory default settings. The FN are functions, and UN are monitoring, these are not changed. However if you are looking for your specific machine parameters settings, the only help I can give on that is sometimes the machines manufactures will include these parameters on schematics, or other machine documentation. your own company should have these parameters either in the machine documentation files or on a computer where you will need the SigmaWin+ software. Hope This Helps Tom
Dear Sir If I upload program for new series 2 servo pack just only write program or need to do something like tuning
If you're talking about auto-tune it's always good to Auto-Tune it sets up your servo or your motor for the highest performance possible
Sir I need your help, our drive is fault we plan to buy new drive ,I has program for that machine .now I want to write program to new one. What's my doubt only write program and jog is enough or tuning need can tell me how to do kindly help me sir.
Please share the link of unidrive SP software.
Just added to Comments section. Scroll down to bottom of page Click + to expand the download section. If you are not registered, click Register and fill out info. After registering Log In. Go back to downloads and PowerTools Pro v6.0 should be loacated near top in Software section. Have Good Day Tom
@@tomh2466 I have downloaded power tools pro v6.0 but its screen is not like the program which you have shared here.
@@roohullahyasini2396 That was 5.0 screen I believe that you can still download the 5.0 in the 4.9 if you go back to the website and scroll through
@@tomh2466 sir! please kindly share your whatsapp number or email
How to rotate dc motor with 50ad yaskawa drive
Please tell me
Sir how to contact you
Great Video!! Very helpful and informative. Is there a way to export the description/comments of the bits and rungs once you have the program uploaded?
Thank you Sir