วีดีโอ

@nav021298 Hello mate, thanks for watching🙏

@@Muharem91 Hello mate, thanks for watching! Yes, there was quite a bit of carbon buildup in the inlet pipes, and I cleaned as much as I could. No, I haven’t taken off those engines. Thanks again!

@@zier66 @zier66 Hello, and thank you for watching! That was the exact same antifreeze as recommended, just in red. Thanks again!

@White87Boy Hello, and thanks for watching. This customer has the same problem after recall. Thanks

Bavarian says its,not related with recall and they dont want to fix it how can i prove them its their fault m one week after recall my car has engine lights and increased fuel consumption . They blamibg intake manifold and saying its very common in this model which i dont buy straight after recall my car having problems and 2 years before recall all good 😢

@@White87Boy Unfortunately, it is challenging to determine if the issue is on their end, as they are likely to attribute it to the intake manifold problem. Thanks again

​@@akisgarageltdany tips how i could challenge them about it ? Its purely their fault after recall ...

@White87Boy I really don't know, but just try and see how it goes.

@charlesford-i8h Thanks, mate 🙏

@johnydepp8334 Hello, and thanks for watching , i used Xtool, but you can do with diagprog4 and dashcoder, I don't think you can do it by carprog . Thanks again

​@@akisgarageltdthanks for reply i am new in this field what device was silver one. I have sm2pro.

@johnydepp8334 Unfortunately, it is not possible by am2pro. Thanks again

@ozdenguney2715 Thanks for watching. Unfortunately, no. Thanks again

@charlesford-i8h Hello mate, and thanks for watching .

@Albert2K7 Hello, and thanks for watching , i am using cgdi hex editing. If you have any cgdi tools and then can use it, or if you Google it, you can find lots of hex editors . Thanks again

@joaquinromero1231 (Hola y gracias por ver) Hello, and thanks for watching.

@@tamarasalehi9583 ❤️❤️❤️❤️

@abdou7001 Hello mate, and thanks for watching.

@akisgarageltd you're welcome 🤗

@charlesford-i8h Hello Charlie, I hope you're well. You will always be my master, and you always help me with remaps and all those things. Thanks so much for your support .

@charlesford-i8h I would never forget those days we used to straggling, and it was very hard to find solutions on software and programming the ECU'S. Thanks again for everything

@davidwaters1227 Hello, and thanks for watching. That's no problem at all. If you disconnect the battery before you do the job and contract the battery back once you have done the job and then it shouldn't have any error code Thanks again

Great, many thanks for your quick reply. I forgot to ask if there’s a specific torque valve for retightening the steering wheel nut, I don’t have a power tool like you use in the video but I do have a torque wrench. Thanks!

@davidwaters1227 you are very welcome my friend, I think it is around 50 Nm (37 ft. lbf). Thanks again

@ Super, many thanks!

I’ve hit a problem, I can’t pull the steering wheel off the column spline. I assume there’s a special service tool that acts as a puller, have you any suggestions for what to do without this special tool? Thanks again.

@@tamarasalehi9583 ❤️❤️❤️

@androidacademy-9752 Hello, and thanks for watching, i don't think so. You can do it by IO Terminal, obdstar dc706, and maybe by smoke too. Thanks again

@wallytanss97 hello and thanks for watching, all power and ground are connected with the p004 adapter. Thanks again

@ thanks for reply

@kohzad1000 Hello, and thanks for watching, i just undo the bleeding bolt on the expansion tank and keep toping antifreeze until all air comes out . Thanks again

@garethwilliams2147 hello and thanks for watching, obdstar dc706. Thanks again

@@akisgarageltd thankyou your videos are informative, i have io terminal clone but find it very hit and miss on what it can and cant do especiially with psa bsi units its let me down on a dispatch before so want a better unit that can clone :)

@garethwilliams2147 you are very welcome my friend, i had very bad experiences with clone fake tools, and I always use genuine tools, more confident and safe. Thanks

@KOOLPOOL-r5p Hello mate and thanks for watching. No, it copied all data from the old module and wrote it back to the new module, and the car started straight away. Thanks again

@gunay.akdogan hello, and thanks for watching. It's very easy. They are around 8 screws mounted to the airbag. Thanks again

@akisgarageltd thanks for the reply. 🙏 Just make sure that, there is enough space to tighten the screws to the dash. (without removing the dash)

@gunay.akdogan no it doesn't need to remove the dashboard .

Many many thanks

@@tamarasalehi9583 🥰🥰🥰

❤❤❤

@didiusngemela4533 Hello, yes, you can clone it very easily with io terminal . Thanks for watching.

@fabulouscarsmore909 Hello, what program did you use? If you used the original io terminal, that should just plug and play, and you do not need any coding or programming. Thanks for watching

@hodgy60 Hello, sorry that's was my early video with not a lot of experience. Thanks again for watching

@GlobalAutoEx Hello, and thanks for watching. If you took the intake out already so you should have lots of space. Check it from under the car. Maybe you missed some brackets or ... Thanks again

@@akisgarageltd Yes, there was actually a 5th bolt holding it to the block. I must have miscounted when I counted the bolts on the picture of the replacement part, lol. All is well! Thanks!

@@GlobalAutoEx👍👌🙏

@@improbablehandle thanks for watching 🙏

@MrLorolla Hello, and thanks for watching , I have used Autel maxisys ultra, but I'm sure you can use most tools to diagnose it. Thanks again

@joramsante376 Hello, No it doesn't. Thanks for watching

@user-og5ud2tz6i Hello, and thanks so much for watching . I think you can progrom the RFA module by Ford IDS. Thanks again 🙏

@BINADI.AUTOSERVICEBINADI Hi, you can get the wiring diagrams from the obdstar dc706 . Thanks so much for watching👍

@@akisgarageltd thank you

@huvernavarrete6494 Hi, the adapter called Universal ECU Bench Cable. chiptuningshop.com/product/universal-ecu-pinout-cable/ Thanks so much for watching.

Hello, and thanks for watching. That was for Ford Mondeo. I believe that from 2007 to 2014, will be the same BCM.

Great video ,additional knowledge for everyone..thanks! how to cloning RFA module for ford EcoSport 2015 titanium using OBDSTAR?.

I think you can progrom the RFA module by Ford IDS. Thanks again 🙏

@samdavinchi1624 thanks so much for watching 🙏🙏🙏

❤️❤️❤️

@samdavinchi1624 thanks so much for watching 🙏

سلام ، بله ایرانی هستیم. ❤