วีดีโอ

Thanks! You solve my issue with the mounting of the spring! Now I understand how it should be mounted!

hey, good video. Could you please put the link of the tool? I want to make sure I won't buy the same. Thank you.

Great vid. Hoping for more English content soon! Have fun racing the car when its done!

Great Video! Unfortunately I just found it after I had done those by myself. I ran into the same problem with the diameter of the ring from the fancy tool being too small . I used a chisel to widen it a bit. Worked perfectly fine and I was lucky I saw it before putting force on the bearing.😅 Still I am happy that I found this channel and hope for good videos in the future! Still one question: how did you manage to fit the tool for pushing out the bearing? The brake line clip was in the way and my tool hat no Notch for it to fit. Using the ones for bearing to fit through did not work either. I ended up using pneumatic jackhammer😂

Alot

Hi there. How did you know that only the right side strut needed replacing? Thanks!

for my vision is the Tool scrap

Great job👍.

May I ask is that a standard 19mm sway bar?

Hello, "Ristus Garage" I was analyzing your channel and saw that in your channel have some problem, That's why your channnel is not much growing and not getting much engagement, If you can solve these problems, Your channel will grow like a storm. If you tell I can tell these problems. Where can I tell? Here or email?

I want to see it finished

there is more easy way to open car with empty batery

Great video, This is the best walkthrough I have found on the entire internet. Im getting ready to do the same soon and feel better about it now.

this must be the worst video on TH-cam ever! No lights, no Engrish no, preparation....

Hyvä kone.

I would hope that you would be teaching that youngster how to use jack stands when you are underneath a vehicle especially when you are shaking it all around very very dangerous glad to see you did not get hurt

Jag skulle vill ha se hur du skarvade den, nämligen ska också byta min s60.

Tuliko kuntoon webaston vaihdolla?

Part number, please

Helpoimmal pääsee kun ottaa satulan ja olka akselin irti ei tarvi vääntää kankia mutkalle ja uhmata sormia😂

Et kehtaa laittaa linkkiä kyseiseen alapallon asennus työkaluun ?

Olen nähnyt videoita joissa laittavat lisärasvat niveliin. Raottavat tiivistettä sen verran. Raidetangonpäät,alapallot ym. Tiedä sit,onko näin vai tehtyjä juttuja 🤔😊

Ihan oikea työkalu. Kiitos.

How much would this cost me ? I have a 2009 XC70. I have a oil leak but can’t able you pin point where it is exactly happening from. Any idea how much it will cost if I wanna fix this whole problem?

Olisko darttonin putkille tarvetta

saikos siellä ajaa muun merkkisillä autoilla ku volvo?

Huikea projekti ja lopputulos varmasti kaiken vaivan arvoinen 👍 Itse en ymmärrä raksahommien päälle ollenkaan, enkä vastaavaan lähtisi ikimaailmassa... Eipä ole tontilla rakennusoikeuttakaan jäljellä, että sinänsä 😬

Tää homma toimii oikeesti.

Jaahas huumenissani ohitti porschen suolenkillä 😂

Hienoa jälkeä syntyy, tsemppiä projektiin! Näiden yksityiskohtaisten videoiden lisäksi jos saa heittää idean - miten olisi timelapse-tyylinen video koko projektista, onko suunnitteilla? Tyyliin 20 minuutissa raadosta valmiiksi, voisi olla hauskaa katsottavaa. Tai vaikka ennen valmistumistakin, olkoon sitten part 1, part 2 jne...

p̶r̶o̶m̶o̶s̶m̶ 💐

Yes I will get gimbal.

Näyttäs että taas puretaan.

Good work 👍