The Boost Barn
The Boost Barn
  • 49
  • 298 396
SKIDOO 850 MULTIPLE BASE GASKET, PISTON PROTRUSION MEASUREMENT
in this video I show you how to measure piston protrusion on a skidoo summit 850 engine. if you get a gasket kit and are confused on why their is so many gaskets this is why. it's very important because the wrong set can cause pre det. .
I made the holder for the dial caliper. you want to 0 the gauge then measure off the 0. each gasket has holes. that represents the size. 6 holes equals 6mm, 7 holes equals 7mm. you can change that over to inches like I did. each mm is a .039 inch. and if your off do the math to figure out which gasket fits your needs.
thanks for watching
ski doo skidoo summit 850
มุมมอง: 377

วีดีโอ

09 rmk 800 boondocker turbo
มุมมอง 96ปีที่แล้ว
vail pass colorado.
DIY Floor Truss Follow up
มุมมอง 11K4 ปีที่แล้ว
We received so many emails asking for more details on our specific truss design so we went ahead and created another video going through it in more detail for everyone looking for more. These trusses covered a 32ft span, were each 2ft high, and we made 30 of them for our building. We saved about $5,500 by making them ourselves. Once we had everything pre-cut it took about 20-30 minutes per trus...
DIY Floor Trusses
มุมมอง 82K4 ปีที่แล้ว
We built our own floor trusses and saved a ton of money, this is how.
Rachel Hollis unboxing and review May 2019
มุมมอง 2885 ปีที่แล้ว
Check out Rachels line here: qvc-advocate.sjv.io/Cassie This is my review of the striped v-neck tee in navy(link:www.qvc.com/Rachel-Hollis-Ltd-V-Neck-Stripe-Tee.product.A354061.html?sc=SRCH) and baseball hem dress also in navy (link:www.qvc.com/Rachel-Hollis-Ltd-Knit-Baseball-Hem-Dress.product.A354057.html?sc=DTLR) that just launched from the new Rachel Hollis LTD clothing line! Only avaiable o...
BMW s50 DRIFT CAR Gender Reveal Burnout!
มุมมอง 1.2K6 ปีที่แล้ว
Find out what gender baby number three is with this epic gender reveal burnout!
Tyler Cox Survivor Video Seasons 39, 40, 41, 42
มุมมอง 4406 ปีที่แล้ว
This is a quick submission video for Survivor Casting.
532awhp Subaru Forester
มุมมอง 1677 ปีที่แล้ว
dan gaynors forester precision turbo 6262 mazworx sleeved block manley turbo tuff rods manley pistons supertech valves bc springs bc280 process west intake treadstone intercooler id 1300cc injectors 532 awhp on c16, true numbers on a mustang dyno
scubadoo sno fun
มุมมอง 7611 ปีที่แล้ว
busting through trails with the subaru
ZX7R
มุมมอง 27812 ปีที่แล้ว
just another toy i picked up.
Tony stunting a gainer, jumping of nh truessel
มุมมอง 5912 ปีที่แล้ว
Tony stunting a gainer, jumping of nh truessel
FreakinBOOM Sinking a Battleship
มุมมอง 10112 ปีที่แล้ว
FreakinBOOM Sinking a Battleship
Dune buggy crash
มุมมอง 75512 ปีที่แล้ว
Dune buggy crash
POLARIS SWITCHBACK 600 WHEELIE
มุมมอง 10K12 ปีที่แล้ว
POLARIS SWITCHBACK 600 WHEELIE
GOPRO HERO HD
มุมมอง 8712 ปีที่แล้ว
GOPRO HERO HD
PEANUT BUTTER WHEELIE TIME!!!!!!!!!!!!!!!!!!!!!!
มุมมอง 45013 ปีที่แล้ว
PEANUT BUTTER WHEELIE TIME!!!!!!!!!!!!!!!!!!!!!!
mach z 800
มุมมอง 88213 ปีที่แล้ว
mach z 800
Project MACH Z 800, MBRP can
มุมมอง 30K13 ปีที่แล้ว
Project MACH Z 800, MBRP can
SKI DOO MACH Z 800
มุมมอง 28213 ปีที่แล้ว
SKI DOO MACH Z 800
02 MUSTANG GT BURNOUT
มุมมอง 29K13 ปีที่แล้ว
02 MUSTANG GT BURNOUT
1963 AMC RAMBLER BUNOUT
มุมมอง 93513 ปีที่แล้ว
1963 AMC RAMBLER BUNOUT
KICKER CVX HITTING 144.5
มุมมอง 70313 ปีที่แล้ว
KICKER CVX HITTING 144.5
POLARIS XC 600
มุมมอง 30913 ปีที่แล้ว
POLARIS XC 600
XC 600+ mach 1000 MBRP and SNO STUFF RUMBLE PACK
มุมมอง 1.2K13 ปีที่แล้ว
XC 600 mach 1000 MBRP and SNO STUFF RUMBLE PACK
SUBARU LEGACY V.S PONTIAC TRANS AM
มุมมอง 24913 ปีที่แล้ว
SUBARU LEGACY V.S PONTIAC TRANS AM
the build, Two KICKER CVX 12 KICKER ZX 2500.1
มุมมอง 89K13 ปีที่แล้ว
the build, Two KICKER CVX 12 KICKER ZX 2500.1
BADASS RICKJAMES DOIN DOUBLE BACK FLIP
มุมมอง 18513 ปีที่แล้ว
BADASS RICKJAMES DOIN DOUBLE BACK FLIP
GIVING EXO A DEMO
มุมมอง 4.2K13 ปีที่แล้ว
GIVING EXO A DEMO
windsheild wipers flappin, 2 kicker CVX 122 KX2500.1
มุมมอง 1.2K13 ปีที่แล้ว
windsheild wipers flappin, 2 kicker CVX 122 KX2500.1

ความคิดเห็น

  • @SS-xo1px
    @SS-xo1px 9 วันที่ผ่านมา

    Soooooooo mamy "professionals " in the comments

  • @lockgessner
    @lockgessner หลายเดือนก่อน

    Hey for the gussets are you using 1/2 or 5/8 and what grade? This is exactly the size ive been looking for

  • @ja4476
    @ja4476 หลายเดือนก่อน

    Thanks for sharing your video, great work !! Is it possible to know how long exactly are your trusses ? I want to built my garage (24'x34') next summer and want to build 24' trusses. I want to cut pieces this winter to save time next summer.... After a few years, are you satisfied with those trussed ?

    • @tylercox4216
      @tylercox4216 หลายเดือนก่อน

      They are exactly 32' long. Amd yes, I use the upstairs for parts room. It's been quite a few years but it holds up great. I take measurements to make sure it's not sagging every year and it's still holding strong. Not a whole lot of bounce in the floor either.

    • @neonpcmsplus
      @neonpcmsplus หลายเดือนก่อน

      that might not be a great idea in practice. If the cut lumber sits around they long there's a very high probability it's going to end up warped.

  • @Business24353
    @Business24353 หลายเดือนก่อน

    5:50 wops

  • @beavisroadhog9629
    @beavisroadhog9629 2 หลายเดือนก่อน

    Thank you very much for this series. It has given me plenty of good ideas for a structure that i am building very similar to your own. I worked in a factory making trusses a good forty years ago. I can tell you for a fact that any truss you can make yourself within the limits of sound construction practices wil be superior in every way to a mass produced example. I saw plenty of garbage go out the door of that factory.

  • @mattwernecke2342
    @mattwernecke2342 2 หลายเดือนก่อน

    Nice work!

  • @Odinhaus
    @Odinhaus 2 หลายเดือนก่อน

    The problem with this truss design is that you have unbalanced force at the ends of your diagonal web members. This means that your screws in th ends of your vertical web members are enduring the axial forces of your diagonal webs. Depending on your span and truss height, this could be in the thousands of PSI on those two small deck screws, which have shear strengths far lower than that. If you instead continue the “W” design like the center section all the way to the ends, the forces are balanced by opposing web members, which is eliminates the shear stress on the screws. In that design, the only screws needing to withstand shear are the terminal vertical web members that are bookending the trusses. The design uses the same amount of material but is considerably stronger.

    • @beavisroadhog9629
      @beavisroadhog9629 2 หลายเดือนก่อน

      I am inclined to agree with you. The "W" or "M" design transmits the force of each successive diagonal member to the next one in line. The design shown does not do this. Train bridges are made from steel, not pine. That's why they can function without absolute stress on a tiny fastener. Take a look at how many hot rivets are used in train bridges. There are likely 10x as many rivets as you would use screws in wood, and often they are securing multiple layers of plate steel like leaf springs. I used to work at a truss factory and later- a railroad for a lot of years. The design doesn't lend itself well to substitution of materials. This is a very astute observation, and I am glad you posted it, as it will affect my decisions going forward on a similar project.

  • @AndrewFaerber-op8ro
    @AndrewFaerber-op8ro 6 หลายเดือนก่อน

    Excellent information . Thanks for sharing your knowledge. Was your floor truss spaced 24” on center of each one.

  • @crazyDIYguy
    @crazyDIYguy 7 หลายเดือนก่อน

    I'm going to take it a step further and mill my own lumber to build these. I wonder why you picked that specific design with a majority of the angles going one direction?

  • @TheGrilledCheeseSandwich
    @TheGrilledCheeseSandwich 8 หลายเดือนก่อน

    Thanks for all the details 👍👍👍👍👍👍👍👍

  • @TheHomeDesigner123
    @TheHomeDesigner123 8 หลายเดือนก่อน

    How did you engineer this truss design? Can you provide the math for us please.

    • @tylercox4216
      @tylercox4216 8 หลายเดือนก่อน

      I actually got a engineered design that utilized the Warren style truss with a box in the middle. This is the weakest truss you can use. I researched train bridges and they utilized Pratt or Warren style. Basically the closer you get to a 45 degree angle the stronger the truss will be. Then I got rid of the box which is by far the weakest point in the engineering of manufactured trusses. The engineered trusses each box is like 3.5ft wide and the angles are like 27 degrees or something. They use minimal. Very minimal. I overbuilt these for sure but wanted to make sure they would last. I figure if they make train bridges built this way then this truss should work totally fine. There's a few books I read about trusses. One is called design of building trusses. If you really wanna get into it read that. I couldn't type as much Info in here as there needs to be if you wanna talk the math . But you get the jist...

  • @TheHomeDesigner123
    @TheHomeDesigner123 8 หลายเดือนก่อน

    Those trusses are beautiful, however, my building code requires the use of nail fasteners which are stronger than screws, at all the connections.

    • @BigDaddyBanditSV
      @BigDaddyBanditSV 7 หลายเดือนก่อน

      Nails have more shear strength than screws, and screws have more pull out strength. They used nails on the gusset plates, so I believe their methods are good.

  • @mudlakesawmill9332
    @mudlakesawmill9332 8 หลายเดือนก่อน

    Thats so cool. Trusses 16" on center? Negative comments are just jealous plywood glued and nailed i would think is stonger than the steel mending plates used in normal truss manufacturing

    • @tylercox4216
      @tylercox4216 8 หลายเดือนก่อน

      Yes! People think that you can't do anything on your own now a days. Their still standing. No sag. I use that garage everyday. Someone put the peaches in the can

    • @mudlakesawmill9332
      @mudlakesawmill9332 8 หลายเดือนก่อน

      @tylercox4216 thanks for the reply. Awesome work. Your video is an inspiration!! I'm glad you enjoy the fruit of your labor! I've heard stories about manufactured trusses falling apart while racking them.....those look like they would hold up to a hurricane.

  • @Virginia-wb4ze
    @Virginia-wb4ze 8 หลายเดือนก่อน

    I want to thank you for your this video.I have looked at so many videos. This video is the only one that helped me understand. Thank so much

    • @tylercox4216
      @tylercox4216 8 หลายเดือนก่อน

      Thank you

  • @majicman88
    @majicman88 9 หลายเดือนก่อน

    Anyone can build a truss but show me the engineering behind what you are doing and that it will meet building codes.

  • @republicofvegans712
    @republicofvegans712 9 หลายเดือนก่อน

    5:54 you gotta fix that...

  • @chiefwhiteeagle6205
    @chiefwhiteeagle6205 9 หลายเดือนก่อน

    did you have pony walls at all spliting the spand to 15 ft so then you could of used 12 inch trusses

  • @chiefwhiteeagle6205
    @chiefwhiteeagle6205 9 หลายเดือนก่อน

    SO WHAT WAS YOUR SPAN 24 FT OR MORE AND YOU USED 14 OR BIG TRUESS IM BUILING 8 INCH FOR MY WOOD SHOP CIELING SINCE IT HAS MY GYM ON THE TOP ON MY HOUSE I WIL BE USING 9 1/2 ONES

  • @chiefwhiteeagle6205
    @chiefwhiteeagle6205 9 หลายเดือนก่อน

    WHATS THE ON CENTER FOR THE UPRIGHT 2X4 BETWEEN THE TOP ABD BOTTOM CORD

    • @tylercox4216
      @tylercox4216 9 หลายเดือนก่อน

      I made another video, shows my math and reason

  • @BrianDeWitt-i1x
    @BrianDeWitt-i1x 10 หลายเดือนก่อน

    How thick was the plywood sheeting on the outside of the building?

  • @danielbeiersr3642
    @danielbeiersr3642 11 หลายเดือนก่อน

    How long were you spanning with these trusses, how wide were you making the trusses for that span and were you installing them on 16” or 24” centers?

  • @cali1379
    @cali1379 ปีที่แล้ว

    hey I want to build 20 or 21 feet trusses can you help me to figure what size I have to make them where you get that info for yours? thank you

  • @kai6424
    @kai6424 ปีที่แล้ว

    You better adjust that flush nailer

  • @ljpolley
    @ljpolley ปีที่แล้ว

    when the glue freezes it fails. best to keep them inside for a day

    • @TYGIXXER60
      @TYGIXXER60 ปีที่แล้ว

      Yeah we were right there weather wise on the limit of chaulking. It did hold. We made a few test boards to make sure the glue would be fine at that temp. Tightbond can go to 32°f

  • @stevepailet8258
    @stevepailet8258 ปีที่แล้ว

    FOR THOSE WHO HAVE NEVER WORKED WITH WOOD.. END GRAIN HAS ZERO HOLDING CAPACITY.. SO THAT IS A TOTAL WASTE OF TIME. the gusets nails and the screws will do all of the holding work forget gluing end grain make sure you get plenty of glu on the gusets

    • @worldsstongeststrains983
      @worldsstongeststrains983 ปีที่แล้ว

      100%. This would not only fail here in Canada but it would have to be replaced. Lumber must be “on end” and screws are not allowed (10d 3.5” clear shank nails) . Would also require truss plates.

    • @keithschneider6348
      @keithschneider6348 หลายเดือนก่อน

      Putting glue on only one component, should have done both sides of joining surfaces.

    • @rioriggs3568
      @rioriggs3568 7 วันที่ผ่านมา

      @@worldsstongeststrains983 Also in Canada and was thinking of doing my own open floor joists... What do you mean by "on end"?

    • @rioriggs3568
      @rioriggs3568 7 วันที่ผ่านมา

      @@worldsstongeststrains983 They used glued and nailed plywood gussets instead, does the Code require metal truss plates?

  • @amrcnengineer
    @amrcnengineer ปีที่แล้ว

    "Tried to stat it again" God I miss home #GoPats

  • @cheapirishbastard
    @cheapirishbastard ปีที่แล้ว

    How have they held up? Did you find them pretty stout after putting load on them? I appreciate the info. I'm debating building them myself as well.

    • @TYGIXXER60
      @TYGIXXER60 ปีที่แล้ว

      Great! I use the garage everyday. I store alot of parts up there. I check the height every year to see if there's sag and there isn't.

  • @arkansasfasttrailriders9774
    @arkansasfasttrailriders9774 ปีที่แล้ว

    very informative video, thanks for your time doing this jerry

  • @forename_surname
    @forename_surname ปีที่แล้ว

    bomber, nice vid thanks for sharing. curious, how did you control lateral forces from the roof rafters pushing perpendicular to the floor truss direction, to prevent pushing your 2 outside floor trusses over? Just the floor sheathing tying a few sets of trusses together? Collar ties, sure, but if the ties are high enough to keep that space usable (i'm not sure where you ended up putting them), they would need to be crazy strong and rafters stiffened at the CT to Rafter join... looking to do similar and keep structure open like this so appreciate your sharing!

  • @ilonabarteczka253
    @ilonabarteczka253 ปีที่แล้ว

    Did it come back? The white stains ?

  • @teedeykam1676
    @teedeykam1676 ปีที่แล้ว

    Is that concrete

  • @friendlylocal3731
    @friendlylocal3731 ปีที่แล้ว

    This is so helpful. Can anybody share any other plans for this type of truss at different span lengths? I would love to have a book of plans for different floor truss spans.

  • @BROOKLYNZzKiD
    @BROOKLYNZzKiD ปีที่แล้ว

    What did the inspector say?

  • @LoliLife69
    @LoliLife69 ปีที่แล้ว

    Are these 2x6 or 2x4?

  • @LoliLife69
    @LoliLife69 ปีที่แล้ว

    So what is the length and height of these?

  • @annettemehrtens9041
    @annettemehrtens9041 ปีที่แล้ว

    I'm interested in making trusses just like yours, would it be possible to get a clearer copy of the Truss detail sheet shown in the video?

  • @shadowOtero
    @shadowOtero ปีที่แล้ว

    My distress when he split the wood

    • @TYGIXXER60
      @TYGIXXER60 ปีที่แล้ว

      It happens, I typically stay away from the edge

  • @centexan
    @centexan ปีที่แล้ว

    Do not even think about doing something like this without a jig to build them. Exact duplicates will make the job simpler and better n

  • @Rew123
    @Rew123 ปีที่แล้ว

    When you don't give a f*** if your floor caves in.

    • @TYGIXXER60
      @TYGIXXER60 ปีที่แล้ว

      Your such an idiot.....

  • @mberry7a
    @mberry7a ปีที่แล้ว

    With all the man hours I wonder how much was really saved???

    • @TYGIXXER60
      @TYGIXXER60 ปีที่แล้ว

      It took a totaly of 40 hours. What the video doesn't show is me alone pre cutting everything. Also when it was time to assemble there was quite a few of them just me amd my wife made. Considering I dont make 8k a week and the materials at this rime was only 1600, I'd say I did save alot. I didn't have to pay anyone. Everyone was happy to help out. Good friends and family go a long way

  • @larrym6019
    @larrym6019 ปีที่แล้ว

    What was the free span wall to wall length for these? And do your floors bounce?

    • @TYGIXXER60
      @TYGIXXER60 ปีที่แล้ว

      The span is 32ft outside of walls. 6 inch walls. The floor does bounce a lil. But idk if you've walked in houses with store bought trusses but they also bounce. It's very minimal but if your standing still amd someone walks by you Caan feel it

  • @racecitycarbraga9350
    @racecitycarbraga9350 ปีที่แล้ว

    👏👏👏👏👍🙏

  • @michaellowe5558
    @michaellowe5558 ปีที่แล้ว

    Nice job! I am working on similar design: 13" high truss with Pratt Truss design (vertical members in compression, diagonal members in tension), but am concerned about diagonals. With 24 foot span, and loading (40 psf plus dead weight of materials = 60 lb/ft over the truss), I get 720 lbf at the ends. That puts a tension load of 1018 lb on the outermost diagonals. In your design, that would put 500 lb load per screw (looks like you put 2 per diagonal) but then you have the gussets as well. I intend to use hurricane straps on the diagonals instead. This will put 6 #10 screws in shear, and they pass. It's just a PITA to get the straps in, so might go with your method instead. Just need to make sure those nails/screws are sufficient when they go into the diagonal.

    • @TYGIXXER60
      @TYGIXXER60 ปีที่แล้ว

      If you see factory built trusses, they only have nail plates to hold the truss together. My screws were more or less to hold the boards in place while the glue cures. I don't think the screws are moving enough to sheer especially after the gussest were in place and glued together. I made a small joint with gussets. Tried to break it apart and the wood broke in many places but the joint wouldn't let go. I believe the gusses and glue joints are the strength

  • @TheBaconWizard
    @TheBaconWizard ปีที่แล้ว

    Thank you for this, very helpful and generous with your time and knowledge :)

  • @DavidGonzalez-md9je
    @DavidGonzalez-md9je ปีที่แล้ว

    What type and grade of material did you use?

  • @jeremyprince4945
    @jeremyprince4945 ปีที่แล้ว

    Any idea how much weight this will hold?

  • @jeremyprince4945
    @jeremyprince4945 ปีที่แล้ว

    How are your floors holding up is there any sag?

    • @TYGIXXER60
      @TYGIXXER60 ปีที่แล้ว

      No sag! I've measured a few times out of curiosity

  • @buynsell365
    @buynsell365 ปีที่แล้ว

    Great video.......I am working on building some now.......I was thinking of building mine with the 2x4 turned the other way......up on it's side......instead of flat.......will that be ok.....or do I need to build them like you did? I need mine to be 32' long......was thinking of making the depth 20 inches.

  • @chuckhall5347
    @chuckhall5347 ปีที่แล้ว

    I'm sure these are great but why not just use the metal plates that you hammer on the sides like a commercial truss you would buy? I have been in 50 year old attics that had the plates tacked in place and they were holding up fine.

    • @TYGIXXER60
      @TYGIXXER60 ปีที่แล้ว

      They aren't as strong as glue and wood. If you don't belive me, price together two pieces of wood and do two the way I did they try to disassemble them. You will find my way is much more stronger. Altho more time it's worth it. As far as cost it actually would cost more to buy the tac plates then the amount of plywood glue and screws

  • @thudang3039
    @thudang3039 ปีที่แล้ว

    Love this! Thank you for sharing. 😊