วีดีโอ

Clean the clutch plates.....how please!

Where did you find that complete manual?

You don't drain the oil first?

My lcd display says reset but pressing buttons does nothing 🤷‍♀️

Yo traté de arreglar la mía a martillazos y no resultó 😂

Clear, thorough and concise. Legend!

How did you find torquing and removing the flywheel bolt as its spec is 70nm I’m worried it could shear the bolt holding the engine locked in at tdc

This was so helpful This happened to me Thanks mate

What size puller is it

Merci, j’ai remonté mon roulement à l’envers du coup quand le rotor tourne il est en roue libre, il est pas entraîné par la roue libre… du coup Le roulement est à supprimer… 127€ le roulement + 5 jours pour recevoir la pièce 😅

👍👍👍👍

Hi! Excellent video. So I bought a new clutch and measured the pack without the 1 mm end plates and it measured 26.2 mm whilst the minimum for my bike is also 26.4 mm as well. Therefore the pack measurement must include the outer 1mm plates. If you don’t include them you’ll always be replacing your clutch and most certainly unnecessarily.

Great video. Question. Can the seal behind the stator be removed without splitting the whole engine. I’ve an oil leak on my ktm 250 causing charging failure. Can only think leak is from that seal

Mega for this helped me proper 👌

Please advise what MC360 size you have? Will 110/100-18 be ok for 350 EXC-F? Thanks.

2023 One of the best tires I've ever ridden on. Most trails I ride have a mixture of dry, muddy and rocks. I've been able to track out of deep ruts. I even run as high as 16PSI in the mud - That's 1.1 Bar for the rest of the WORLD lol.

Sweet!

How mutch presure should i put on those tires but in bar um from europe

I had an issue with the controller/display not working. It appears that there's a 5 year life span on the internal battery. And since it's a sealed unit, will need to be replaced. Part #: 732-S00 was what I needed. It's not available in NZ for another 8 months!.....so I just ended up wiring in a manual switch. See how much of a PITA that is.....if too much, I'll shell out for a whole new kit. Thanks for posting your diagnostics! :)

my clutch is not wanting to engage, i put the plates in correctly and the dampeners also. i pulled the leaver and it’s just not wanting to move at all?

Terrible tire. I have on my 450 and my backend alway kicks out

I run this tire on my 459. It's absolutely terrible

What would happen if you mixed up the 1mm plates with the 1.4mm plates?

How do you keep your hands so clean as a mechanic ? That’s the trickiest part

Hello, do you know how to remove the electric starter, I’ve tried for hours now and I’m wondering if the only way is to remove the flywheel as shown is this video.

bom dia eu tenho um ktm sx-f 2008 ela já fez um barulho estranho duas vezes apenas alguns segundos e o barulho parece como tivesse dado partida com o motor já em funcionamento ,será que tem alguma dica por onde poderei começar ?

bom dia eu tenho um ktm igual a esse e ela já fez um barulho estranho duas vezes apenas alguns segundos e o barulho parece como tivesse dado partida com o motor já em funcionamento ,será que tem alguma dica por onde poderei começar ?

what type did you test? cause there Hard, Medium, Soft and Super Soft...

Is the cuntrol unit tern on the fan ?

What torque did you set on stator rotor srew, M10 one?

I just got a free new metzler mc360 but wanted this tire but you just said the metzler is better hah

Please review the new Maxxis maxxenduro 7324. 😎

Thanks for reviewing all these dual sport tires, much appreciated. I've bought a couple now based on your reviews.

What's the safety wire for and is it needed?

Would the ignition/stator cover come off without putting it to TDC? Thanks

Did you say 2013? I have 2013 350 excf and want to replace the clutch and rubber dampers. Just not sure which clutch holding tool I need. Some are bike specific plus not even sure what type of clutch I have yet. DDS or the multiple springs setup

My trail tech Fan is grinding internally is there anyway to clean the inside out?

Thank you Sir! It will go live on Monday. th-cam.com/video/FvJm_uUmtUM/w-d-xo.html

Aloha from Hawaii! Mahalo for the video. I have a 2012 ktm 350 xcf. Think I may have the same problem. My E-start will crank but won’t turn over, and my kick start feels like it’s spinning all the gears including the torque limiter gear. I removed the torque limiter gear and my kick start worksite bike will run. I was hoping you could shed some light on my problem. I’m thinking the torque limiter bushings are shot and that’s why it won’t work. However I think it’s more then just that. Could you help please?

Hey there Troy. Love this video. May I use your video in my upcoming Motoz Monday video where I discuss the Enduro S/T?

Sounds like the Motoz was a much better soft terrain tire for you?

I have a 2003 ktm with a crazy knocking nose what is it the top end is new made the noise before and after replacing the top end

giving this a go tomorrow will let you know if i did it right :)

Do you use a Barlow or Powermate? Or is that shot at native F10?

I'd be interest to know if this XC flywheel fits EXC by the axle hole. I don't care about the location of the trigger teeth.

How is the right way to place the bendix ???

Hi ! What is the size of the puller ?

8.5-9psi! Can you go that low with these?

Good video!

Native focal?