วีดีโอ

Two suggestions for your wonderful video, 1) speak out on what you are doing; 2) make the model download ready. Thanks !!

Two suggestions for your wonderful video, 1) speak out on what you are doing; 2) make the model download ready. Thanks !!

Need full tutorial

我们有机会看看 .k 文件吗？

Hello, I sent the request for full tutorial. kindly respond pls

you must put value in LCID -> Plastic region not Elastic Region

Hello, I have a question about how 2 different SPH particles(water and abrasive) are created. I have succeeded in creating a water column using a cylinder shell, but I do not know how to randomly place abrasive sph particles with a certain volume fraction. According to the paper, they used a random replacement program matlab code, but how do I apply this code to sph generation? Thank you for amazing video tutorial.

Hi, can we increase the sph number of particles in a localized way for a particular region rather than the whole part?

Dear sir, How to get the k file?

Please full video 😢😢😢😢

I'm Ph.D. student's now, I currently study about this process. May you send the complete tutorial an email. Thanks!!!

can you upload the complete video?

In assigning the VDC for the contact, you put the value 20 at 11.07 minute. why did you choose this value?

for the specified thermo-isotropic properties in minute 8.42, You selected Heat capacity as the value 642, and for thermal conductivity the value 4.7e-5. Then you used the same values to the tool and the blank which are from different materials. The question is how did you select these values? In addition, can I know which materials you used for the tool and blank?

Firstly thank you for your great work. I appreciate it. But I have some notes. In 7.55 minutes, you chose V0 equal to 1 while you kept E0 as zero. However, it is stated in the help that in EOS_linear_ploynomial, 'V0 and E0 defined in this card must be the same as the time-zero ordinates for the 2 load curves defined in the *BOUNDARY_AMBIENT_EOS card, if it is used. This is so that they would both consistently define the same initial state for a material'.

Great video. Can you add audio with this video to explain the steps involved in simulation

As soon as the cutting tool touches the SPH model, the SPH model disappears. What do you think could be the reason for this?

can i tell you some question?

Where can we find the full Tutorial. The site you refer does not work

Please share .k file

Thank you very much for sharing, I have a question for you: I would like to use SPH-DEM to simulate sandy areas with water, and then do I generate SPH particles directly inside the box that generates DEM particles?

can I get the full video?

Is it possible to simulate ball end milling?

Excellent video! Thanks for sharing!

Great job!!,could you help me with the full tutorial please🙏? I send you an e-mail,best regards!

Hello! I did the vibration mode analysis via the method as your video has shown, but there always was Error 60134 when I run the model document. Did this also happen to you?

Shape imported from another software... Doesn't it easier to use LS-DYNA with Ansys?

Hi how can I make this jet engine? Is there a specific video for help or can I find this jet engines file online? Please help me because I’m really struggling with this and nobody is helping so far.

PLs send me full video of it

Thank you for your tutorial. I'm interested in the ALE method in Ls-Dyna. Could you please share the full training video, 3d file of the boat and also .k file?

кал

Hi sir .. can u plz share the k file . Thanks

Hi sir.. can u plz share the k file ..

Sir i want soil behavior under blast loading I need ur details sir please

Hello! It's a great job!! Thank you so much for your videos and lessons. Excuse me, but could you help me? Please tell me which type of material is better to choose for EPP (Expanded Polypropylene) material. It is used as an energy-absorbing material, in particular as an organizer in the trunk of cars for tools, as well as for inserting under the bumper. I know its characteristics (Young's modulus, density, Poisson's ratio and there is an experimental stress-strain curve). I am very grateful to you in advance.

Can you tell me how to simulate the explosive welding interface?

Hi, I have a question about contact_surface_to_surface. In thermal part (HTC) you placed 45. That number is, I presume, thermal conductivity of material. which material do you put in? the one with bigger or smaller thermal conductivity?

Hi, your simulation is great, can you do oscillation simulation using LS-DYNA. Simulate barrel oscillation when firing for example.

Hi, Where to find the the completel video?

Can you share the working link for the complete video? The link in the description is not working,,....

Please share us the completed video, am very interested on EDem

Hi where can we find the full version?

Can we get completed video of it ?

thank u, do you say some thing about torsional spring?

Thank you sir for your tutorial and it is very interesting but if you can would you mind if you send me the complete video