วีดีโอ

I am facing same problem with my Hyundai sonata 2017. I replaced spark plug 2 times in a month but again misfiring problem due to oil leaking. My technician said to change valve cover gasket and replacement cost around $300. Is it okay? And if gonna be solve this problem after replacement the valve cover gasket ?

Thank you for the video, now I'll for sure take it to the car shop for replacement lol. This looks hard and stressful and I probably lack a few tools

yes

Where to find part number for rogue 2015 sv?

Did it leak oil for you whilst it was damaged?

That is stupid

It's called the childproof lock

Do you have to buy it extra or do they come with the axles?

What model are the struts?

what was the error code im getting P0431 NS Exceed Pajero

If only mine was that easy 😂😂 i just bought a 100$ rotory hammer for mine

Transmission not shifting because of dirty transmission fluid. Wach full video to learn. Before damage your transmission

is the culprit worn out carbon brushes?

Which vehicle type?

Good video bro.. i have a 2004 spectra 2.0 and the temperature gauge dosent indicate that is over heating but after i run it for like 10 min a clicking noise start sounding what can it be ? The oil level is good .. Can it be the oil pump ?

Wach full video of how to get your AC compressor engage because of low freon, use r134a to recharge car AC system

Thank you!!!

What does it mean if it doesnt rotate fully

There is no need to charge your system! If your freon is low then you have a leak. FIX your leak.

There are probably a dozen or more videos on how to do this job properly. This is NOT one of them.

Let a pro do it .If you are using this you don't have a clue

Thank you I was struggling...

Adding freon if too low will turn on the compressor if not broken. No need to replace compressor.

Remember for safety use safetyglass, mask, and gloves for protection

Wach full video learn how to recharge your AC system on cars

If your AC compressor not working. You can still try to recharge then it should start clicking, if not then replace. Or get it checked.

Loosen the nut, hold the bolt

Nice! I see it. 😉 looks good. 💯

Makes no sense. What engine? What year? What car? 🚘

Dude, completely disconnect the brake lines from the strut before you try yanking it out 🙄🙄

Stolen content

Daaam, the break lines are still attached too the strut,😢

Wow!!! Funny how good some people think they are 😂😂😂

Yes Strut assemblies are great but don't let them fall and cut your CV boots and it works better if you remove the break line too!

You forgot a word! How to NOT remove a strut!

Lol brake line

Learn how to replace strut with spring on a 2004 to 2006 Mitsubishi Outlander wach full video

If only it was that easy

Hey brother, my ratio control valve “T” shaped part next to the stepper motor gets stuck. Any idea how I can get it to move in and out smoothly?

How do you check the starter with this scanner?

Full video is out everyone go an wach full video

Do not top off brake fluid. As the pads wear more brake fluid is stored in the caliper. Now when you replace the pads, the master cylinder will overflow. Brake fluid doesn’t just vanish, and if it does you have a leak which needs to be fixed instead of “topping it off”

Refill while your bleeding keep it full

bro you need to do a whole lot of shit as well hahhaa

Um...

Was that neg or pos?

Lol you'll barely get the carbon of the outside of it like that. You need to clean the inside using injector cleaning and flow bench or ghetto it up and apply voltage to open injector and spray brake clean into inlet.

Wow, what a revelation

Try removing the nut first

🇯🇲 yaad man 🤔