วีดีโอ

Hello! More information on the possible flows is available at the following link: info.cype.com/en/subject/cype-connect-workflows-supported-by-the-program/. A usual case is to start the work in CYPE 3D to carry out the calculation of the structure and, then, pass the information to CYPE Connect to carry out the specific calculation of a specific joint. If an IFC file is imported from other technologies instead of being generated with programmes such as CYPE 3D, it must fulfill a series of conditions so that CYPE Connect can interpret it. For further information, please contact CYPE Technical Support via the following link: learning.cype.com/en/technical-support/. Please, indicate the workflow followed and the programme used to generate the IFC. You can also send the IFC file if you consider it convenient to help in the resolution of the case. Greetings😊

Hello Mateus! Portal frame generator is a program that allows you to generate a geometry of members and loads to export it to CYPE 3D. In the latter program, CYPE 3D, it is possible to carry out the complete calculation of the structure and carry out checks according to different standards, modify the geometry received if necessary and add, edit or delete the desired structural elements to optimise them. Greetings😊

Hello! You must enter as many floors as there are pitches or slopes on the roof. There are several alternatives, one of which is simply to use the ‘By points’ input mode and enter the vertices of each slab at its position in space. A reference or sketch line structure can be drawn beforehand, if necessary, in order to have the capture points available at the desired height. If you have a sketch surface, in any position, you can also transform it into an element of type ‘Floor’ using the ‘By surface’ input mode. Greetings😊

Hello! In general, CYPE programs require an Internet connection at specific times, such as when validating an electronic licence or when connecting and linking to a BIMserver.center project. From then on, the programme can be used without an Internet connection, which must be recovered when you wish to operate again with information uploaded to the BIMserver.center platform. Greetings 😊

Hello Carlos! The flow rate defined in the grid shall be the one considered by the programme in case the ductwork does not have a connection to a machine. If there is a connection to a machine, the flow rate associated with the machine shall be distributed over the grids. Greetings 😊

Hello. From "File > Examples" you can load and open one of the examples available in English. Then, from "General parameters", using the "Export" button, you can save this configuration to .bib132 files in the indicated path. In other works, use the "Import" option to select the previously exported file and import these parameters. Greetings 😊

Hello Gabriel. In the current version of CYPE, an IFC file containing the reinforcement can be exported through the application and then imported into Autodesk Revit. This file can be viewed and consulted within the federated model, but it cannot be edited or converted into a native Revit entity. Greetings😊

Hello! Here you are all the information learning.cype.com/en/faq/as-a-student-how-can-i-use-cype-programs/. Greetings😊

Hello! From Open BIM Quantities is possible to export the information to a file in .BC3 format, which can be imported into Arquímedes and, from this programme, generate an XLSX file (from "File > Export" or from "File > Print > Print list"). Greetings😊

@@cypesoftwareEN Ok, I'll give it a try.

Hello. Under the workflow proposed by CYPE, the modelling, calculation and obtaining of the installation documentation is carried out entirely in the CYPEFIRE Hydraulic Systems interface, without the need to move to another platform such as Revit MEP. However, once the model is developed in CYPEFIRE Hydraulic Systems, it can be shared in BIMserver.centre and use the "Open BIM - Revit Plugin" to extract some of the information entered. Information about this plugin can be found at the following link: info.cype.com/en/software/plugin-open-bim-revit/. Greetings 😊

Hello Sasan. This is CYPE Connect. More information is available here: info.cype.com/en/software/cype-connect/. Greetings😊

Hello Gideon, Open BIM Cost Estimator is able to generate the budget estimate based on the parameters defined in the wizard without requiring any previous model. If you need to measure on a model, you can first use IFC Uploader to upload an IFC file with the model information to BIMserver.centre and then Open BIM Quantities, which is a program that allows you to extract measurements from the model, import items from price banks and compose a budget with all of this. For more information (including manuals, courses, seminars and guides) see the following links: info.cype.com/en/software/open-bim-cost-estimator/ , info.cype.com/en/software/ifc-uploader/ , info.cype.com/en/software/open-bim-quantities/. Regards😊

Hello Sergio, the tool is integrated in the "Joints" option of StruBIM Steel, so it is not necessary to operate CYPE Connect independently; it has the same functionalities. Regards😊

Thank you for your comment, Doyoung Choi🙌

Thank you for your kind words, Riaz Malik. We are glad to hear that our content is useful to you. Best regards😊

Hello Harish, thanks for your trust in CYPE. We take note of your suggestion for future content. Regards😊

Hello Harish, thanks for your comment. We take note of your suggestion for future content. Regards😊

Hello Harish, we take note of your suggestion for future content. Regards😊

We are delighted to read this! Thank you for your confidence in our softwares and content😊

Hello, you can opt for self-study by visiting the "Website" of each application on BIMserver.center and going to the "Learning resources" page. You can also ask your sales representative about training possibilities by sending an email to cype@cype.com. Regards😊