- 9
- 27 111
Lectrotab - Electromechanical Trim Tabs for Boats
United States
เข้าร่วมเมื่อ 12 พ.ย. 2019
Lectrotab designs and manufactures premium quality electromechanical trim tab systems for the leisure and commercial marine markets. The Lectrotab system is easy to install on new boats or to replace existing trim tabs.
Lectrotab Trim Tab System Installation
Video shows how to install a Lectrotab Trim Tab System on a boat.
มุมมอง: 3 018
วีดีโอ
Functions of the Lectrotab SLC-11 Control
มุมมอง 4.6K3 ปีที่แล้ว
This video shows you all of the functions of the Lectrotab SLC-11 One Touch Leveling Control for trim tab systems on boats.
Lectrotab SLC-11 Control Programming: Remembering last trim tab setting
มุมมอง 2K3 ปีที่แล้ว
This video shows you how to program the Lectrotab SLC-11 trim tab control to either remember the last trim tab setting or auto-retract when the key switch is turned on.
Lectrotab SAFC Rocker Switch Upgrade to SLC-11 Control
มุมมอง 9793 ปีที่แล้ว
Lectrotab SAFC Rocker Switch Upgrade to SLC-11 Control
Troubleshooting procedure for Lectrotab SLC-11 Control
มุมมอง 3K3 ปีที่แล้ว
Troubleshooting procedure for Lectrotab SLC-11 Control
Lectrotab SLC One Touch Control to ALC-1 Auto Leveling Control Upgrade
มุมมอง 2.4K3 ปีที่แล้ว
This video shows the steps involved in upgrading from the Lectrotab SLC-11 One Touch Control to the ALC-1 Auto Leveling Control.
Lectrotab ALC-1 Auto Leveling Control Calibration Procedure
มุมมอง 7K3 ปีที่แล้ว
There are a number of features on the ALC-1 Auto Leveling Control that can be programmed. This video shows you how to makes changes to these programmable features.
Lectrotab SLC-11 Control Programming: Changing the stroke time function
มุมมอง 1.4K3 ปีที่แล้ว
This video shows you how to change the stroke time on the Lectrotab SLC-11 control. The stroke time function is just the total length of time the control sends power to the actuators. It cannot speed up or slow down the actuator. The actuator speed is a function of it's design, specific to the model number.
Does the Aux wire get abandoned since it can't be used in the Optional Terminal #7? I'll be replacing an Oval switch with the ALC-1. Sounds like a great product and a much simpler installation than other options out there!
Dear Sirs ! Will the One Touch SLC-11 Work with Lenco standard elictric trim tabs ??? Thank you very much for answering ! Best regards
Dear Team, Is there any possibility to get the stock for Lectrotab SETR-61.
The SETR-61 has been discontinued. The replacement is the SLC-11. It is a very easy upgrade.
@@lectrotab-electromechanica7101 PLEASE HOW I CAN SWAP THE LEDS. WHEN I PRESS THE PORT, THE OPPOSITE LIGHTS MOVE.
Good video thanks. Does the ALC-1 retrofit the SLC-11 opening in the dash and is there anything else needed for this to work or is it just the ALC-1 unit?
ALC-1 will fit in the same hole at the SLC-11 but you'll need to drill 2 small holes for the mounting studs on each side of the ALC-1.
Is there a way to tell what actuator you have? I bought my sportsman brand new but my paper work doesn’t say what l have although l have that switch panel
Call us at 804-268-8428 and we can guide you through the process. There is a serial number on the top right of the actuator that will tell us exactly what model and year that it is.
Hi there, I have just purchased one of these auto controllers to fit my existing Lenco tabs. However, I do have 2 questions regarding the calibration process. 1. Should this calibration be done whilst on the water when the boat is stationary sitting in its natural state, or can it be performed on the trailer? 2. If on the trailer, does the boat need to be sitting somewhere near the same plane as if it was stationary in the water? Or can it be levelled out. With a full tank of juice at the twin outboards on the back, my boat sits quite arse heavy in the water, just wondering what is the best way to go about this.. Any help would be greatly appreciated, thanks.
Calibration can be done on the trailer on in the water, inside or outside. No GPS signal is required for the calibration either. The orientation of the boat is not important for calibration.
Hi sir i have a (( 2000 sea ray 240 sundancer )) and i have the factory trim tab its working good can i remove my trim switch and install this one or i have to change all the unit ? please let me know so i can buy one . Thank you
To answer that we'd have to know what type and manufacturer your original trim tab system is. You can call us at 804-368-8428 and we can discuss it with you. Thank you!
@@lectrotab-electromechanica7101 Thank you sir i will check it when i bring it home from the storage and will call you .