วีดีโอ

Mcculloch was much better back in the 90s

That 700R is definitely a good weedeater.

That is a cub cadet, in fact, this is an MTD type product. Even Troy Bilt, Craftsman, Bolens, cub cadet are all by MTD, which is now a piece of shit company. My mom had an MTD riding lawnmower years ago, and it was a decent machine. MTD has gone downhill, especially when it comes to production of mowers, string trimmers, blowers, chainsaws, etc. I will never buy a four cycle weedeater. I had a four cycle toy built it for a year, and it got replaced by a STIHL. If you want a quality trimmer nowadays, buy a Husqvarna, Echo or Stihl.

Dude that spring is upside down

Why is that old sled so clean? How'd you do that?

Thats the simple part,no one on you tube has done an install of the suspension properly,or two "lummoxes" on the floor wrestling those two middle small wheel idlers screws with the shock tension on.everyone can take stuff apart,but putting it back is the challenge.those two control arm bolts,disconnect for the shock end both sides,ratchet strap compress the rear shock with the small wheel idler bracket ,wrestle and install it.By your self its easier putting sled on its clutch side.takes most of the weight of the skid to do it alone.its a bitch. Dudes and the manual that say reverse the take off procedure are buffoons.Ive done it a few times alone and it works well.becareful when it drops your fingers arent in the way,believe it crushes your fingers.

can't see

Are you putting in a heavier spring, my friend keeps bottoming out on his.

Your supposed to unscrew the plug wires before taking them off

The caps are in the plug wire

I’ve got two sleds ripped apart at the same time right now too. My garage is trashed. Srx 700 and rs rage.

1991 murray, this is my favourite mower iv wanted on since I was a kid

7:05 My fuel pumps on both of my mowers are in a different location than on the carb. Do I need to buy another fuel pump to install on the carb and take the one on the firewall off? It just looks weird with nothing on the carb side, but I couldn't find any entrance holes on the side of the carb for it anyways. Mine just looks like 12:38

did the jackshaft bearing on a phazer (2007). it was not as easy as the driveshaft one I just did on the nytro, but oddly enough was the same bearing. I went OEM on the phazer jackshaft original was NSK.

What a waste of my time. Ten minutes in and your just taking out the screws. I don't care about steering slop. I don't care about main jet. 16 mm socket? Really? You think there is something metric on that 20 plus year old engine? Think again. And use a socket or nut driver on those three screws on the air cleaner. And at 13 minutes your talking about I don't know where the springs go.

I paused your video at 20:47 and zoomed in on the stamp on the side just above the spark plug and could see the model of your engine is 400707.

...is this for $ale??(wherest???.. just curious)

Nice operation 👍

Could you spell that paint name please this has come in very handy

Getting it out is easy. Gravity is your friend. Getting the last two bolts in during installation is a bit trickier.

Always buy oem !!!

It’s been forever hee finally unleashed the demon in him

How long have you not uploaded😭😭😭😭

A mi me pasaba lo mismo le cambie el carburador santo remedio ......

my spare bearings from my 03 sx viper fit just right on my 03 rx1. I enjoy how compatible yamahas parts are, knowing they must have done something right to keep the bearings the same from rig to rig. currently making my own rs vector gt but installed a rx1 engine. lotta good work, but surprisingly everything is bolting on as intended. sweet rig you got there buddy, hope you're having a swell winter. ✌️ just subbed! cheers from Alaska

nice language, foulmouths

Been there,done that. The exhaust is a pain too. I did the exhaust repair from FX Garage works. It takes a bit of fit and finish but we'll worth it, do it once and done!!!

I use Partzilla. OEM parts but 30% less than my local dealer

I changed my jackshaft bearing a couple years ago, pain in butt, now every year I pop the seal off that bearing and repack it with fresh grease

heyyyyy

I just changed all the drive bearings on my Warrior this spring, now I'm glad I spent a little extra for OEM parts.

Greatest video of all time, a true emmy award winner, golden globe, oscar winner

What is the model number I got one just like it but can't read the numbers

Straight heat😊😊

If your mowing less than a tank full why bother More than take a gas can with you

Keep up the grind 🔥

That is one awesome vintage weedeater. Surprisingly it still runs after all these years.

Is that a Ryobi 700r?

The color I used isint a very close match...check out the murray restoration Playlist for the correct paint because I found it then did another repaint

Ok...holy cow i didn't expect this many views from this video..I'll make more of these!!!

Quality 😉

Was that now??

Nice Intro 🔥

Murray lookin freshhhh

Hope u feel better soon!

Am I here no way

R.I.P 1 VIEW 😭

1:25 is probably the part you want to see most...

Gavin the coming soon was good But you should have done a black screen and a dramatic effect