วีดีโอ

There is no sound for me to understand

here is a tip for figuring out your rafter lengths ... take the span in your case 30 feet convert it to inches that is 360 inches now multiply it by the Sine of 22.5 ....360 x 0.3827= 137.772 now convert the decimal to fraction by like this 0.772 x 32 =24.704 in this case round up and you get 25/32ths of an inch so cut each rafter from long to long on 22.5 degree angles at 137 25/32ths of an inch and Presto you have perfect Gambrel roof

I used your method and found a hidden gem. I may have been a degree off of your numbers, but it all worked out great. When I added the optional joists, I used 8ft 2x4’s that I only needed to trim the top angle. They fit perfect between the lower gussets where the boards met. My shed is 12x16.

Hope to see the finished product

Should last a long time, nice job

Thanks for the help. I'm making a parcel box in the shape of a barn for all that stuff I order. Your directions are very clear.

Could you use OSB board instead of ply? Could you fix gussets on both sides of the connections .

Great information ! I am building a 10ft but 18ft building. What will the length of each part of the rafters be? Thank you for any help !

Can’t wait to start making mine! Already have a gravel foundation build and leveled .

Can I assume at 1:14 that those 2x4 lengths are on the top side? Obviously if you measure on the bottom side, they will be different because of the angled cuts at the ends.

I am building a 10x10 barn shed and I totally can’t figure out the angle cuts on my trusses. I want to do a 5 foot wall, and I want the center highest point to be 8 feet

Please can you help me what’s the degrees angle for a gambrel trusses for 10’x12’. The width is 10’ , length is 12’, wall is 7’, loft is 5’, total height 12’. I followed your video and I got the rafters length 3.61’ for both lower and upper. I just need the exact angle degree for each end of lower and upper rafters.

When you are screwing in the gusset - what is that bit?

Very good series of videos.

Hate wrong title should be titled "laying out foundation Blocks, wasted my time.

Wow! This is the best video for a barn gable rafter roof. 😍👍😍😁🎉

what is the size of your shed

Wasted wood

This is not a 6ft roof

I am replacing the roof on 10x10 shed with barn style so can have a loft. Plan to make the truss span 12' with the hopes of extending the building at a future date. Hoping the overhang will greatly reduce rainwater damage to siding on walls.

Can this method be used for larger span...28 ft..

This was very informative. Thank you. Tomorrow, I will be reinforcing rafters on a garage. I'm not sure what the dimensions are off hand and I'm not sure what gussets exist, if any, on the rafters. This is in northern Maine and there is a significant snow load. Question regarding fasteners: is there any reason not to use PL2000 and nails rather than structural screws?

Somethings wrong with the mic. How did you figure out what angles to cut.

Is it about the same for gable style roofs too?

That top angle is also 22.5. Both angles together need to add up to 45. The lengths you have work perfect with all angles at 22.5. Just my 2 cents.

Hi.. Good stuff! Did you ever finish the rest of the build? Thanks again.

Is it possible to have a version of this where the working screen takes up the whole screen? Thanks.

That was great teaching thank you sir. You helped me I'm subscribed will you be my carpenter father?

*I built a shed with these plans from Ryan [ Check Details Here=>**lovy.biz/etxg** ]. The instructions were clear and easy to implement. Even a novice can be able to build fast using this plan. I'm happy I bought the plan. It also saved me much cost.*

Hi Richard. What is the width of your floor plan?

Excellent video; You have made a complex process very simple. There are some very good videos out there but this one is the best, in my opinion.

cant find door framing video

I don’t understand it how many degrees are the miters

Give me a shoutout

Give me a shoutout

Give me a shoutout

Give me a shoutout

Give me a shoutout please

Booo

Thank you, very detailed and helpful 😊

Good video.

Good job. Going to try it tomorrow. Thanks

excellant

I want to make that type of roof but i need one the is 5 ft high and 12 ft long. The angles of the rafters change??

4:47 magnetic driver guide

Is there a formula you use to determine the length of each board that depends on the width of the structure?

Thank you

interesting and helpful videos. I am planning to build a bunkhouse with gambrel roof. To avoid having to get permits and inspections I have to stay at or less than 100 sq ft, so I will find 8X12 plans and use your 12 ft truss video. I copied your foundation layout video, your truss videos, and this wall video but I can't find your floor video. has it been removed? Thanks for posting these videos. I am copying them to a laptop to help me during the build in a remote location without internet or cell access. Great work Richard !

awsome video

Nice job