60
79 779

4:03

3D LabPrint Hurricane MKII

4:04

Piper J3 Cub with float over Po river

1:54

Piper J3 Cub with floats!!!!

6:09

Piper J3 Cub by 3D LabPrint with floats

1:42

Piper J3 cub by 3D LabPrint

1:36

Hawker Hurricane MkII by 3D Labprint

Winter flight of my Hurricane. After reprinting it I no longer colored it because I fear it might warp again in the summer heat. The model flies very well with a 1300 mAh 4-cell Li-Po, 9*6 propeller and 30A ESC. I wouldn't change anything about this setup. The fixed landing gears are very robust and as you can see the landing strip is very short and full of obstacles. Recommended model aircraft!
3dlabprint.com/shop/hurricanemkii/

มุมมอง: 63

วีดีโอ

4:03

Fouga CM170 Magister R/C (3D printed)

มุมมอง 11521 วันที่ผ่านมา

I could have done a better job with the landing, the cameraman with the shots... Anyway, the Fouga is gorgeous and flies great! Thanks to Planeprint for this project!

4:04

3D LabPrint Hurricane MKII

มุมมอง 1988 หลายเดือนก่อน

I apologize for the bad camera work but, at the moment, it is the only in-flight video I have of this model aircraft. Very poor landing!! Model setup: Motor: Very old Hacker A20-22l out-runner Prop: 9*4 Esc: Mystery 40A Li-po: 14.8V 1300mAh 60C Servos: 4 * SG90 micro servo (9gr) Printing file at: 3dlabprint.com/shop/hurricanemkii/

1:54

Piper J3 Cub with float over Po river

มุมมอง 1.1Kปีที่แล้ว

Last nice flight for my Piper J3 cub from 3D Labprint. Unfortunately, after this, a wing servo failed immediately after take-off and this caused the model aircraft to impact on the water. Luckily I had with me the boat for the recovery that did its duty. More infos here: www.rcgroups.com/forums/showthread.php?4135391-3D-LabPrint-Piper-Cub

6:09

Piper J3 Cub with floats!!!!

มุมมอง 635ปีที่แล้ว

A short flight with takeoff and landing from the water for my Piper J3 Cub. Now the center of gravity is perfectly positioned. More details here: www.rcgroups.com/forums/showthread.php?4135391-3D-LabPrint-Piper-Cub

1:42

Piper J3 Cub by 3D LabPrint with floats

มุมมอง 609ปีที่แล้ว

A short video of the first take-off and landing from the water of this small 3D printed model aircraft. The project can be downloaded for free from here: 3dlabprint.com/shop/piperj3cub/ More info here: www.rcgroups.com/forums/showthread.php?4135391-3D-LabPrint-Piper-Cub

1:36

Piper J3 cub by 3D LabPrint

มุมมอง 990ปีที่แล้ว

A simple 3D printed RC piper J3 cub, printed with LW-PLA. More informations here: 3dlabprint.com/shop/piperj3cub/

Fouga Magister CM170 R/C by PLANEPRINT (NEW!!!)

3:49

Fouga Magister CM170 R/C by PLANEPRINT (NEW!!!)

มุมมอง 1.6K2 ปีที่แล้ว

My 3D printed R/C FOUGA MAGISTER More infos at: www.planeprint.com/product-page/fouga-magister My setup: EDF: FMS Platinum series V2 70mm 12 blades 3060 motor 1900kV 6s it.aliexpress.com/item/32961101785.html?gatewayAdapt=glo2ita&spm=a2g0o.9042311.0.0.40074c4dXIbdbI ESC: Hobbywing Skywalker 80A with 5A BEC www.aliexpress.com/item/32963160568.html?spm=a2g0o.9042311.0.0.5ebd4c4d3BFWmm LIPO: 22.2V...

3:37

Aichi M6A Seiran Crash!!!

มุมมอง 4044 ปีที่แล้ว

This is what happens when you want to take off without having enough speed! Buy here: 3dlabprint.com/

Aichi M6A seiran water takeoff maiden (flop!)

4:11

Aichi M6A seiran water takeoff maiden (flop!)

มุมมอง 2694 ปีที่แล้ว

First attempt to take off from the water with my Aichi M6A. The engine should have enough power but I think the propeller is not adequate. I was unable to take off. I'll try again with bigger propeller and with less pitch.

AICHI M6A by 3D Labprint maiden flight (Nanzan version)

4:23

AICHI M6A by 3D Labprint maiden flight (Nanzan version)

มุมมอง 5894 ปีที่แล้ว

Test flight for my Aichi. It's a 3D printed plane. Landing gear pieces: www.thingiverse.com/thing:4151762 It flies beautifully Buy it at 3dlabprint.com/

6:26

RC Rescue Boat

มุมมอง 8805 ปีที่แล้ว

Simple RC air boat created to recover not working RC seaplanes. Tested on Po river in flood (Italy). Construction based on this video: th-cam.com/video/Z-ux4Lzrpeo/w-d-xo.html Thanks to Andrew Newton.