วีดีโอ

If it says Martin on the label then yes it does.

I bought a customX 12 string because it played and sounded fantastic. After playing it for a couple of months, i started looking for a Martin 6 string. I finally came across a custom X 6 string. In all honesty it played and sounded as goid if not better than several of the other more expensive Martins on hand. I took it hone and it is now one of my most prized guitars! I love them both and wouldnt trade them for anything!@

Just bought a Breedlove Pursuit EX S Concert BB CE from Reidys, really nice guitar, but the tuners are awfull, buttons all rattle & fall off, tightening does nothing, they still undo and fall off, the actual buttons themselves don't sit square on the shaft and super loose horrible fit

Thanks Drew

Nice and clear video - thank you! My motto is to clean any hidden parts just as if they were right there on show on the headstock. (Same goes for car restros as well.)

Another Really good talk about the Really important meat and potatoes of the acoustic guitar. I feel like Graphtec pins should be in the 4 th ( middle) row there ?

Really hear it on the “G” string.

Nice guitar! I think if people use lighter guage strings on their guitar, and also always remember to tune it down if in storage or if not playing for a while, that might help to not need a neck reset so soon in the future. Sort of like a type of preventative maintenance. And also I think if people use heavier strings on their guitars they might be more likely to have problems in the future, as they have a lot more tension. Would you agree?

You are a god send! <33333333333333

Augustine more natural need running in .

In other words his ability is in the tips of his fingers and thumbs, and cannot be transferred to you.

Isn't this guitar right handed. Based on F cut design

There should already be a strap button hole pre drilled on most acoustic guitars. I use a small paddle bit judiciously until i get the right dimensions for the stew mac reaming bit. Just think before you do,and do not rush the process. A little blue masking tape over the hole helps from maring and splitting around the end pin hole. .maybe a very light lube,like graphite dust on the end pin jack. The hardest one i ever did was a gibson cherry red sunburst humming bird. What friggin mess,red mahogany dust and shavings. They must dyed the guitar inside out. Just ridiculous.

Hey bro, here’s a Tip’- begging for money is Pathetic🤌🏻🥳

If I was Martin and wanted to break into the affordable guitar side of things, I’d rather have the guitars made from wood overseas according to my specifications instead of making this laminated rubbish.

This glue is not available in my country

Good point for ordering strings.....and anything else re using the P/N . Side note ..... I was informed ... by two Company reps .... that the name D'Addario .... Is correctly pronounced Dad-dario..... Not Dee - a - dario . Just saying , since everyone wonders what the correct way to say their name is .

Thanks Drew!

Broke one of my Nylons Tuner Heads last week, went to multiple local music shops including Guitar Center, none of which had any just "laying around", like it were something needing to be sweep up at the end of each night or something lol. Granted I wasn't talking to their Techs but they acted as if I was the first person ever to come in asking about them. Next day I went into shop when I knew their tech would be in and he charged me $1 It's not always as simple as you say and in the meantime one must do what one must do. I used pliers for a few days but mine looked nothing like that one and replacement worked np. Seriously whomever took pliers to that Guitar was a Butcher. If you gotta go a Night or two, just be careful.

is it NOT marked on the Orange drop??? =/ I mean a simple + / - symbol would SOLVE this confusion

64ths? 32nds? How can people live like that? There's a reason most countries reformed their unit systems last millennium. That being said excellent information in this video.

Thanks Daddy!

Ya this is the second time this donk said solid to solid back .The fg865 is all solid, but you have to special order it

Great video thanks. So the black plate of the pickup should be grounded, too, right ?

Perfectly articulated!

I was today years old when I learned why "crowning" is so important. Thanks!

Adirondack spruce has wider grain pattern. The best.

I just received my Yamaha ft3 made in China and it is flawless. The action was perfect. It does have the plastic nut and doesn't seem to affect the tuning stability. I am now a big Yamaha fan.

So if I buy one of these through GC or Sweetwater etc, where can I get these mods done?

You better use grease! Works fine for the matal! Not Wax... Wax is for candle and is fragile...

You mean to say the direction of these capacitors isn't standardized in relation to the print? You have to test every single one to find out? Wow, that sucks.

Thank you man, this is an important thing for any musician to know, especially if you under fire w/ no backup guitar. I would recommend taking a picture before removing the switch for correct orientation and I used 70 percent iso alcohol cause I'm cheap. Thanks for the video!

Hi, Great vieo. Could you please explain what the white part added to the saddle used for?

1:17 Damn Neil Young in a guitar demo is something I can say I've never heard (song is Old Man)

I have a guitar that appears to have have hazy areas on the backside. My understanding is that it’s from too much humidity? Curious what someone would recommend in this case.

The string worked marvelously! I could not get a slip knot to work but I tied the simplest overhand knot around the pins and they came right out. Thanks for the tip!

i do not have a tone knob

1:33 can't you buy a knockoff fret rocket and rectify all the faces and make it work flawlessly?

That's good advice for more than just your guitar...

What about using ebony (or other hardwood) for nut material for an electric guitar?

did you mean don't "ever" glue your nut?

Came here through the bridge pin removal video, figured I could use a refresher on stringing. You definitely helped me up my game!

A few years ago, I convinced the store where I bought one of my acoustics of this very problem. They conceeded when I insisted they check. A marked improvement when they corrected the "flaw".

Hey Drew thought I’d leave a comment saying hi. About a decade ago you taught me how to refret a takamine neck (among other luthier- esque skills). Fun times. Still have that takamine and to this day I use guitar knowledge I learned from you back then. Hope all is well.

It still seems there on your High E when you strumed the g chord. I have the same problem when I strum chords on my tailor GS acoustic. Mainly on the treble and D string, the same High pitched ring is there. And its a very High end guitar. This problem hasn't always been there until recently. I've tried everything to the point I don't even want to pic it up. Shame because it was a beautiful guitar to play , not to mention expensive. Great trouble shooting vid to watch. But I still can't find the problem. Cheers mate

Hi Drew Can you talk about what to do about the last six frets buzz and hump at the body and what you can do? This seems to me to be a problem many acoustic guitars have weather there new or old.. any suggestions?

Thanks for this, very cool. Always heard the guitar caps orientation doesn't matter. I've always have a feeling it does. Need to make that gadget right now. Subed! Spokane here by the way.

Thanks for this! I've been hunting the source of hum in my dual LA2A I just built, and narrowed it down to either a ground issue, a tube issue or an issie with the orange drop caps I have i btween both the triodes in the firsr part of the amp stage. I would touch the orange drop that was physically positioned inbetween both tubes in the amp stage (this is why I couldn't ruel out the tubes) andit would basically do what you are showing in this vid! I bought a couple of solen fast caps to replace them, but they havven't arrived yet, so now I'm going to switch the polarity of the orange drop and see if that fixes it! Ta for the insight! I had no idea these changed in performance with polarity. But seeing the diagram makes it obvious why that is!

Cheers buddy, I successfully fitted one using the second option wood drill bit, just to add that at the beginning I slow sped the bit in reverse which gently got thru the top finish first, more as a scoring action to prevent any tear away. My sharp bit actually got in a couple MM in reverse, creating a nice starting point for the then slow forward drilling.

Mine has a poly finish on the fretboard and neck. And I absolutely hate it. No idea why anyone would make one with such a sticky finish. I love how my guitar sounds but not how it feels. And it needs ss frets. What can I do to strip it a reseal it with something more satin/matte feeling?