วีดีโอ

Good video❤

Thank u

how to find out the resistor values in real aplication for example the design of boost for supplying bldc controller ... thank you for the lecturer

Perfect explain, and i see the Arabic voice in your explain, please make Arabic language as same as the English

🙏

I'd like to suggest not to use 0.5 for the step value, cause most likely a current will be zero there, and PID artifacts won't be available.

Very good tutorial. Please what software are you using for the simultion?

This is very applicable to a SMPS of a sound amplifier let's say, but 50Hz inverters have two switching frequencies, and this is called an inverter. We cannot change Ws, it is always 50Hz independently on a load, and we only change Wpwm parameters. 50Hz inverter is actually a D-class amplifier (and harmonics are defined by different reasons)

Could the matlab file be available please?

Thank you sir. What software is this?

Congratulations on the exceptionally good explanations. Could you inform what software are you using for the simulations? Thank you so much.

Thank you very much.

Sir are you using MATLAB for simulating ?

SIR PLEASE BRING MORE VIDEOS LIKE THIS

Thank you so much for explaining the modulation index. Really appreciate.

Actually all you proven is that there are no even harmonics for this one case involving a highly inductive load and a full bridge rectifier. This does not consider other load cases. For example if you had the same highly inductive load and a half wave rectifier and ran the same analysis you will find that even harmonics do exist.

Insightful, thank you sir🤩👍🏿

Good work Dr. Ahmed

Amazing. Thank you Ahmad and Br from Germnay

Sir how to make level shifted please help me

So nice thanks sir

Great explination, thank you

I have a basic question. Do this circuit only convert voltage unregulated for make the isolation purpose or do this circuit do both isolation and DC control regulation at the secondary side. Do this circuit need a second regulator for control the DC voltage level.

I found a Power Electronics M204CXR today. Iwould appreciate some advierte on how to determine whether it is functioniing properly.

Good day, I would like to know the Vout formula for the three-phase half-control

How to chose the (L,c,L) value

Thank you for this video. Could you do another video of implementing MPPT and PI controller to control output voltage of the boost converter using PLECS? Also how can a battery cell be modelled on PLECS?

Fantastic explanation

Thank you Prof. it was so good explanation, Prof could you do next video about adding parallel passive damping filter to this inverter Best Thanks

You're my Hero.

This is how a traditional (not UcD) D-class amplifier with a full-bridge output stage works. Can be called an inverter if you like. However for 50/60Hz it's better to use a table with coefficients for a PWM in a microcontroller, rather then all these generators and comparators. Besides, a phase shift switching is simpler to implement with an MCU.

After some years not studying (because I started to work in the Industry) in the last months I decided to finish them. Getting back was rough but yesterday I aproved my penultimate Exam for graduating as Industrial Engineering. This videos helped me a lot getting back to this subjects. Great explanations. Thank you!

Great👋

Sir, there is little mistake I guess.. In mode-1, S1 and S4 are conducting and in mode III, S3 and S2 will conduct.

Thanks 🙏👍💯😊

What is the name of the simulation tool used in this video ??

Thanks , that's is great lecture, good mentioned.

Sir can you please explain how you calculate ∆v/v voltage ripple for capacitor

Your video is very helpful, but I have a question that, what duty cycle will you choose to generate drive pulse for mosfet, D =0.2 or D=0.8, hope you will answer soon. Thanks

Great video.

Thnx 😍

Thank you so much.

Such a great video, I was looking for something like this for so long!

i don't think that the single v-loop inverter will has any application value.

CCM or DCM??

👍👍👍👍👍👍👍👍

How to calculate the input capacitance ?

hey, can you show the matlab code of this series parallel resonant converter.

Thanks ! Can we get the Matlab file please ?

Very useful video but do you have the last part of the video updated anywhere?.. I wanted to know about the control when we input the boost converter output as the control set point to the PI controller (as you talked about the change of gain of the controller according to the boost output)