วีดีโอ

Just use the other connector behind the ac all u had to do was

Have 2002 3.9v6 dakota 4wd doing. Just changed timing cover gasket waterpump thermostat twice. Second i drill hole mod in 195* thermostat. Also changed plugs wires starter Alternator Idler pulley Tensioner pulley Belt. Backflush heatercore. Do need new valvecover gasket and manifold gaskets too its smokey Its not burping am trying this later tomorrow.

Darn was hoping to find video on actually repairing it...

Would have been a good opportunity to use KiwiGrip awsome stuff with great slip resistance.

any idea where we can buy the L bracket pieces (the one you removed to get the 2 sides to split)? Ours was rusted out and broken in the pool we bought. Thanks

Thanks helpful

My door lock gets stuck when it slides to lock and unlock I know there’s like a metal bar inside the door behind door panel how u fix that

Nice job!

Its a real annoying design flaw. Wheelbarrows in the UK have a better design as the handles are slopped so its more level overall.

Good idea, I have done it myself but cut the starter solenoid wire instead, switch in series, but I like your idea less work.

hi, the new rix k3 has 17 degree FOV but 2x base magnification. How does that fit in here? is the 2x base a further reduction of the FOV? I can't figure it out. Thx

Stoic.

Good work, looks fun ngl

I have a 150 lbs Great Dane we call the baby shark. I blacked out the back windows with the darkest tint I could find, and using a reciprocating saw, I installed a drain in the floorboards for what BabyS leaves behind.

Nice I’ve been looking at magview for 180 dollars lol. This is much more in my budget

Great video. I have a 2001 GMC Sierra with a slightly different issue...I have no back lighting on my door switches. All fuses seem good and I cant seem to get them to work. Do you know if this switch controls these as well? Thanks.

Thanks for this video!

it's funny because I bought that special tool and still can't get it off. thanks for the video

Them ole Kubotas come thru every time. Makes me wished I had kept my old L 2650.

i always enjoy your videos, very informative. too bad we aint neighbors, i dont think i would get into half as much trouble as i do... i live down a 1 mile road in the woods.. i have gotten some good info from u . Cheers and thanx! dont stop!

Those roads look icey. Black ice. Looks fine but next thing you know your in the ditch.

Identifying bad ammo should have been the first step.

Seeds start to sink and Stink. Bacteria gets really bad in a day or two! Nasty! I developed a solution.

Great idea. Saving money by using fantasy is awesome 🎉🎉🎉🎉🎉

Hello good afternoon sir , I used this video to help me do mine on my 2000 chevy tahoe 5.3 2wd and you helped me with my struggling … I want to thank you and god bless you sir subscribed and liked and commented .

Great video ! So glad I found it !

2002 Polaris ho I bought new. I took mine apart 3 times to clean the carb and your video solved my problem. I had to hammer the screws like you did. Napa didn't have the o ring HD site said they had it but nope so i went to orlays and got it for $0.65. Wasn't as tight as I wanted but it worked . Thank you so much for making this video. I was stuck not knowing what to do. 5 stars man if you don't shut the gas off after use and let it die on empty carb it creates problems eventually Oh yes lets not forget about the Tip on the gas. My oil was way too full. and clipping the little hose THanks again

That is really well done! Thank you for sharing. I’ve been looking for a pre made discrete case for a while, other than a pickle ball case most of it still looks like a gun to anyone that’d have a clue. Other than tools being more likely to get stolen than a tennis racket I’d say it’s perfect. Since I’m not leaving it in the truck it’s perfect for my needs. Now I just have to see if I can find a case to fit an 11.85 inch.

Great setup. I have the same size boat. Are you using a 24 X 36 tarp?

28 years same 12ft v hull.....dropped my battery on my drain plugs tube last trip out to the lake......may try this route before hiring out a tig welder

would have been nicer if you videoed the actual removal and installation processes.

I really think we need to start getting more aggressive. Like, don’t even bother with immobilizing it, just set it up to where you get a notification when it moves without you, remote activate the door locks and window locks (to keep them in), then, remote activate the taser in the driver seat (make sure you reupholstered that seat with conductive thread at each seam), and watch the show via the dashcam with your loved ones. 👍

It's so you can bleed your brakes by yourself. Can you hook up the air compressor and pressurize it with a little bit of air. That way you don't have to have somebody sitting inside the vehicle pumping on the brakes while you're bleeding at the caliper.

Thanks for the help .

Hallo would you please share the part code for the gasket? Thanks

Good job!

Need a third blade angled like the first blade to make it run straight. Or little more weight on front. Nice work though!

Have you tried your grubber mounted low on the tree with the chain over a tire? Pulling the tree up first. I've seen big stumps pulled out using that method.

Thanks

I just bought a sport boat with a similar trailer but am going to extend the trailer tongue by two feet

THANK YOU ! This video answered lts of questions i had. I have the same issue and will gather all tools needed and fix it soon !

Your planting a little late on brassica in your region ain't ya?

Thanks for the video❤. I’ve been searching for a pole for my new bat houses. Where did you even find a 20’ pole? That’s my biggest problem 😕

When reaching back how do I know which is the sensor ? I will be doing this job this coming weekend I'm hoping I can do this without taking everything off

What gauge and type of wire did you use for this job? Thanks!!!

They're should be no problem, dissembling that firearm fully sir. I know the newer blrs are made different but what you got is smooth as to be there's no messing with the gears like on the newer aluminum frames blrs, the bolt is different as well on the newer ones they don't rotate and they have a funny shape on the rear of the bolt the cut out I should say. Don't own firearms you can't fix or disassemble because your gun is useless if you have no knowledge on it . But I don't care that's on you or anyone dumb enough not to understand YOUR OWN gun.

Dude,your insight and reality on "BIDENS AMERICA" is proof your level of knowledge is as sharp as your mechanic skills. Thanks

Hello, I have the same exact motor and I am wondering when you disconnect the shift linkage and drop the lower unit down, is the shift linkage supposed to be screwed into something? I am able to pull the rod all the way out of the lower unit, and it has threads on the end of it. I am worried when working on it with my brother, he twisted it out of the linkage inside the lower unit. Any insight will help. Thanks in advance.

Thank you my friend. Just finished mine.

Nice came here to see if others were already doing the same or everyone using fancy glue dispensers 😅 gonna use an agave syrup bottle 🤓 have a nice day too