วีดีโอ

Thank you so much ❤

This helped me a lot

After living with two Sig Sauer We The People 1911 .177 for a year, first one, then the second, contracted the dreaded CO2 dump affliction in both magazines. While there can be multiple reasons for such malfunctions, on my two examples I found just one, and found it could be mitigated by simply preventing that CO2 cylinder from turning while you tighten. Did you ever notice how your CO2 cylinder sometimes spins with every twist as you tighten it to pierce? Why is that important? The piercing valve at the top of the magazine is counter-threaded, (righty-loosey, lefty-tighty). So when you tighten the CO2 against the piercing valve, as it is pushed against it hard, it has a tendency to actually turn the valve itself slightly. Especially if you properly lube the top of an occasional CO2 with a drop of Pellgun Oil like you should, to keep the O-rings, seals and valves in shape. Counter-intuitively, unlike a brand-new unlubricated gun in which the tip of the CO2 "grabs" the dry white (in my magazines it's white, could be green in yours), seal as it's getting pierced, mostly preventing it from turning even if you don't tightly hold it, a properly lubricated setup may not "grab" as well and spin. Don't think skipping the lube is a solution... that white seal really DOES need to be lubricated to prevent it drying out over time. Thus, as time goes by, CO2 cylinders eventually spin REALLY easily as you tighten to pierce them. It's surprising just how hard you then have to grip it to stop it from turning inside the magazine as you do. As you tighten and pierce the CO2 and it spins clockwise while you're doing it, trust me that cylinder is pushing hard against the piercing valve seal, which it will inevitably turn clockwise too, loosening it, if only just a little. As once was famously said, a little got more and more... PFFFFFFFFFFFFFFFFFFT! Worst part of all this is that it's darn near impossible to find a valve key (like the one that you got in the re-build kit!), that will fit within the confines of my empty magazines which would allow me to simply and easily just tighten that damn valve, leaving you to use flathead screwdrivers and the like, potentially damaging the needle or valve itself while not being able to really tell just how tight you got it. I eventually took some online advice I saw, carefully UNSCREWED THE PIERCING VALVE, removed and cleaned the o-ring or (replace it if you have one), cleaned the threads and put the o-ring back on, silicone lubed it all, then WRAPPED PLUMBERS TAPE AROUND THE WHOLE THING, both the mounted o-ring and threads, before COUNTER-CLOCKWISE screwing the assembly back in as tightly as I could with no valve key. Another drop of Pellgun oil to top a new CO2, and tighten. While I got a quick sputter it immediately became silent - it held air! Since then, even leaving a full CO2 loaded for weeks or even months has caused me no ill effects as long as I kept the white piercing-valve seal "hydrated", kept from drying out. And following these instructions. So as a preventative measure, if you grab your CO2 tightly while getting loaded. you'll probably always have a nice day!

Is their another lubricant I can use if I don’t have silicon oil?

As a speedsofter I can confirm that we can’t afford lunch 😭😭😭😭😭😭😭😭😭😭💀

wait until mr speedsofter finds out about Novritsch's minigun with a stock. that thing would blow his mind

My glock mags were leaking this and a bit of silicon lube sorted it out thank lad

My mag is brand new and its leakin

Big help man appreciate it 😊

anything about a ssp18 mag? it has a valve close to the top as well and i thing that may be leaking

This video saved me 50$

Mines leaks from the top

Does anyone have the link for the fake suction tablets cuz I can’t find them on Amazon and feel weird continually looking for fake morphine

my airsoft mag did this thing where i pushed the cap lock thingy and it got stuck in the mag and like the mag works and all but the cap isnt locked its like in the lock hole

What about 14 year old

I dont have that sadly 😅

thank you so much

Thank you

Is the thing supposed to be dry or no

Done the job! Thanks

Thank you

You sir are a legend best feeling ever fixing your own gear

Iam taking a shit while watching this. What is the context?

Speedsoft is a modern kamikaze

Very good had a leaky mag where the base plate o-ring was dried out your video worked like a charm

Cheers man, video helped fix 4 of my pistal mags

A lot of mags also have a piece at the bottom of the feed spring that you can pull up with a finger nail instead of using a pokie pokie tool.

Shit video

Thank you so much. Was about to get 2 mags fixed and it would have cost like 50€

Thank you so much! I really appreciate videos cutting to the chase

This helped so much, thank you! Also, the problem in my mag was that it wasn't screwed on tightly, so if someone was wondering if their problem is not being solved, maybe you just have to screw it on more tightly.

Hvor har du købt din fcpc😮

I was trying to empty the gas from my GHK glock magazine but in expelling the gas, it shot out the rubber gas route seal from the top. I reinserted it back into the magazine after cleaning it off, but now the magazine won't hold gas at all. It doesn't just leak, the gas goes in from the bottom and equally expels out the top. Never had an issue like this before.

I prayed and it stoped leaking! You are probably the man of god cuz i prayed normally it didn´t work, i did this thing then prayed and it worked! Thank you!

Know this is 3yrs old.. But thank you 🦾

1:15 is when vid starts

So helpful bought a 2011 second hand of my mate and one of the mags was leaky did a quick troubleshoot using your video very quick and easy vid class lad

I messed it up cuz of you, Tysm!!!! $50 to the drain 💀. I think I turned it too much and too hard it snapped on me

this dude looks like the guy in hello neighbor

Why do i get a mini seizure every time he transitiones cameras

Mine doesn’t have that release button on the bottom.

What brand is your prc 148?

Mil sim all the way

Mine leaks from the back of my gun where u hold it from

I guess I’m milspeed

hope to see your mws and what you modified

nice to see what you ended up with :)

Nice loadout!

Still look forward to your videos guy. Do as much as you can or want....good with me.

I take EMT class at my high school and am Stop the bleed certified and CPR certified and I love playing a medic role for milsim and I have a plate carrier and I am being so serious all you need is GP pouches that you paint the Red Cross on them and then fill them with required items