วีดีโอ

its a 1200s sportster i own 1

Nc face book marketplace

I got one for sale

Need a weak spark it490 to go with it?

Scrap it

I’ll buy it off of you

Not a wood screw. It also had a washer. 20 years automotive industry you find those coarse threaded screws in bearly every make and model from 2000-2020

just do a top end??

What spring rate did you use in the forks?

'Bought a used KLX/DRZ110 for my son almost 20 years ago; he learned to ride motorcycles on that low-buck automatic. It's in a shed in Maine, used in Summer, we still have the thing- if an MC novice rider-to-be visits and wants an introduction to motorcycling it gets pressed into service as a pit bike. I bought a 4-speed shift drum and a new cam and intake for it back in the day, but never installed the shift drum; too much work. Now that I don't really use the bike anymore it may be a nice relaxing little project. It would have made the bike more useful years ago for those time swe needed to take a higher-speed jaunt on a back road between trails!

Looks like a lot of fun for $400 A potential contender to ride in the Toy Run?

The sportster guys seem to like your video

Wear safety glasses 😊

My buddies Harley did that like last week, except there was no warning.

Don’t worry it’s a Honda 😊

I know what's wrong with it, it ain't got no piston in it!

A bad noise? HAD to screech like a banshee for half a second, ouch

What a tit, if you take advice then your a tit too

Don’t hold it down like it’s life or death and you won’t need to worry about it

most drills have an adjustable clutch and u can set it to the proper resistance for your application. i dont think leaving the chuck lose to slip is good advice

no. youre using the wrong bit and youre drilling too fast. use cobalt tip bits millwuake are the best and go slow like a drill press with steady pressure. have someone spray oil on it while you drill or if youre alone drill a little then spray then drill more then spray

Thos is not good advice.

I’m a plumber. I have a good luck pipe wrench.

I was gifted my good luck hammer. She’s an old Craftsman ball peen hammer. I think she’s older than me.

The right tool? Try a quarter lol.

I have a 30yr old hammer and it never lets me down

I agree with this. I have several in my box and there is 1 that does good work

Ryan will use fourth in the Desert

Hmmm. Yeah. I suspect there just isn’t a big need for that 4th gear on a 110. 😂

Thanks for the great video! Gives me hope that I could do it in 20 minutes! Or at least in under an hour!

This is extremely helpful! Thanks

I have a 1997 sportster that ran yesterday but I took off the intake & carb to clean it out today, put it all back together & now it won’t start, any advice?

Love this! A blast from the past! You all have grown so much! A bigger shop, bigger bikes, and more importantly a bigger “boneyard”! Well done y’all!

Hello, is there any way to contact you?

Good one! Glad you got it!

Another runner! Good job buddy!

Make a nice go-cart engine! 😮

Nice! Count me in for next year!

Great shots! Caught me nearly bombing the creek crossing at 1:33. Figures that the one part of my ride that gets filmed is a near-miss. Pour one out for the many drowned Huskys and KTMs that day.

great vid! thanks for posting it. 👍

Great video bro. I think my little jet is clogged. Hard time taking off until revving high

Made the mistake of unscrewing the choke cable housing on my sporty… it snapped… new one on the way😅

Anyone else want a PB&J after watching this?!!! 😂😂😂 hell yeah, what kind of grease?

Or ya know just use your phone 🤦

Looks like a blast.

Looked like a great ride

Rad vid Jonny!

Man just got one for $50 runs but the crank case cracked f’in Hondas 😂

Work smarter not harder! Good one.

Love those old TTR’s! Great bike!