- 56
- 34 408
LET IT SHINE WELDING
เข้าร่วมเมื่อ 23 พ.ค. 2015
Welding tips, trick, technics, career advice and much more.
Weekly welding videos.
Carbon
Stainless
Aluminum
TIG
MIG
STICK
SPECIALTY WELDS
Weekly welding videos.
Carbon
Stainless
Aluminum
TIG
MIG
STICK
SPECIALTY WELDS
Pull Vs Push with MIG welding. How to properly overlap welds.
www.tiktok.com/@natalio1812?_t=8rppQI8LkBa&_r=1
natalio1812?igsh=a3l1Z3VybnI4YTJi&
share/183VuZo8pa/?mibextid=LQQJ4d
natalio1812?igsh=a3l1Z3VybnI4YTJi&
share/183VuZo8pa/?mibextid=LQQJ4d
มุมมอง: 962
วีดีโอ
How to hold an electrode without getting gloves or hands burnt. How to feed the electrode (rod).
มุมมอง 5Kหลายเดือนก่อน
How to hold an electrode without getting gloves or hands burnt. How to feed the electrode (rod).
3G MIG, downhill root, weave hot/full & cap. How to restart on root, how to do a proper dry-run.
มุมมอง 397หลายเดือนก่อน
3G MIG, downhill root, weave hot/full & cap. How to restart on root, how to do a proper dry-run.
How to prevent undercut, porosity, slag inclusion, inconsistent weld, etc… welding with 7018/6010
มุมมอง 2.6K3 หลายเดือนก่อน
How to prevent undercut, porosity, slag inclusion, inconsistent weld, etc… welding with 7018/6010
How to better weld the bottom of a 5G / 6G pipe! 6010 / 7018 stick welding.
มุมมอง 4553 หลายเดือนก่อน
How to better weld the bottom of a 5G / 6G pipe! 6010 / 7018 stick welding.
How did you get your first welding job? What should I do after welding school? What can I expect?
มุมมอง 7554 หลายเดือนก่อน
How did you get your first welding job? What should I do after welding school? What can I expect?
How to be a better welding instructor & a better welding student for greater success!
มุมมอง 654 หลายเดือนก่อน
How to be a better welding instructor & a better welding student for greater success!
How to put a welding stinger/electrode holder together. How to put a welding ground clamp together.
มุมมอง 3534 หลายเดือนก่อน
How to put a welding stinger/electrode holder together. How to put a welding ground clamp together.
How to properly prepare and fit a pipe for 6010 open root!
มุมมอง 4535 หลายเดือนก่อน
How to properly prepare and fit a pipe for 6010 open root!
How to use and oxyfuel cutting torch. How to set a cutting flame on a cutting torch.
มุมมอง 3396 หลายเดือนก่อน
How to use and oxyfuel cutting torch. How to set a cutting flame on a cutting torch.
My welding story, my career in welding, my first job in welding, welder career path I took.
มุมมอง 1186 หลายเดือนก่อน
My welding story, my career in welding, my first job in welding, welder career path I took.
How to strike a 6010, 7018, welding electrode, rod, SMAW. Welding 101
มุมมอง 4756 หลายเดือนก่อน
How to strike a 6010, 7018, welding electrode, rod, SMAW. Welding 101
Oxyfuel cutting torch, torcha, como cortar metal, soldador.
มุมมอง 1029 หลายเดือนก่อน
Oxyfuel cutting torch, torcha, como cortar metal, soldador.
Oxyfuel cutting torch, how to set up a good cutting flame & get straight, smooth cuts.
มุมมอง 2.3K9 หลายเดือนก่อน
Oxyfuel cutting torch, how to set up a good cutting flame & get straight, smooth cuts.
How to put on and adjust your welding helmet ($$$ Maker).
มุมมอง 409 หลายเดือนก่อน
How to put on and adjust your welding helmet ($$$ Maker).
6010 3F T-plate & vertical overlapping welds.
มุมมอง 4.1K11 หลายเดือนก่อน
6010 3F T-plate & vertical overlapping welds.
3G GTAW (TIG) all the way out. Welding with LET IT SHINE WELDING ✨
มุมมอง 342 ปีที่แล้ว
3G GTAW (TIG) all the way out. Welding with LET IT SHINE WELDING ✨
3G stick out, open root. 6010 root, 1/8” land & gap. 7018 full & cap.
มุมมอง 612 ปีที่แล้ว
3G stick out, open root. 6010 root, 1/8” land & gap. 7018 full & cap.
Let us do your will on earth as it is in heaven. My testimony. A taste of Gods love. PT 1
มุมมอง 342 ปีที่แล้ว
Let us do your will on earth as it is in heaven. My testimony. A taste of Gods love. PT 1
You're a Marine, brother? Sub'd af. Let it shine!
Pushing and pulling your beed really depends
Are you doing a 105 demo? 😂 Man I don’t miss running that phase
I feel you, bro. One of my least preferred welding processes.
The penetration profile is different from push to pull both have there use. Push is a lot fatter and pull is just a hair deeper
Yeah, the penetration is the biggest difference. Pull method has the wire constantly going into the puddle, resulting in deeper penetration. Push method has the wire going away from the puddle, leading it. Giving enough penetration for a solid weld. LET IT SHINE ✨
Good info! glad i stumbled upon your page
Glad I could help. LET IT SHINE ✨ out of curiosity, what helped you out? I’m going to do another open root for the 2G & 3G next.
i use a pair of ceramic tipped reverse tweezers instead of holding with the glove. works really well
Smart. Let it shine ✨
Wow hat job on extremely basic. Do a minisota key hole
LET IT SHINE ✨
Great tips 💪
Thank you, Frank 🙏. Those arc shots are awesome, can’t. Wait till the next time 👨🏭
👍🏻👍🏻
LET IT SHINE ✨
As a beginner, i found this very simplified and informative. There are not a lot of videos on this subject, but there should be. This technique has help\ed improve my beads way more than any other one single video I've watched to this date. Thank you.
Thank you for the feedback. Blessed to be able to help yourself & others. Any ideas on what you would want to see next or need help with? LET IT SHINE ✨
Badass! Yep i hold it like a pen until my gloves are prune shaped! Lol Stay up!
Thank you 🙏. LET TI SHINE ✨
Hey I signed that hood 🤘🏽
You also gave me some wisdom & knowledge brother 🙏. Iron sharpening Iron ⚔️
Very good tutorial, clear demonstration of this technique !
Thank you 🙏. Happy to help. LET IT SHINE ✨
@@letitshinewelding3787Thank You sir!
Very good video!
Thank you 🙏. LET IT SHINE ✨
Tremendo video, de los mejores que he visto. Muchas gracias
Mi plaser 🙏. LET IT SHINE ✨
Downhill! Wtf kind of welder goes down hill. Stop making videos
I think overall this happens if you don't prep your metal properly. Am I right?
Correct, light mil scale and rust makes a bad difference from a clean or questionable weld.
GG
Great stuff
Thank you. Hope you got something out of it. Let it shine.
CS almuniam mix filler cod plies send
i gotta question boss, i'm on 1g and i'm having problem with porosity with 7018. I'm only getting porosity when I start the line in the very beginning and not anywhere else. What is the cause of this problem? my instructor is telling me to hit the arc and hover outside of the plate for a second and then come into the plate and build the puddle and start the line, is this the only way?
Great question. With 7018 the flux plays a huge part with porosity. We have one clean start with 7018 which is the first strike of the arc. If you have a clean start 90% of the time you will have a good start to the weld with no porosity. Porosity happens when we don’t have a clean start. If you get stuck on the first or multiple tries get the grinder and clean out the arc marks & then restart. The electrode needs to be showing metal at the tip but with plenty of flux covering it. If it’s too long of a metal peace, even an 1/8” without flux porosity will happen 99% of the time. I believe your instructor was referring to that, if that’s the case then hold it off to the edge of the metal and let the electrode fully inflame and then bring it down to the 1/8” - 1/16” arc length and start your weld. I do a flicking technique with my 7018 so I won’t have to break through the hard flux when trying to restart. I’ve attached a link to one of my other videos that shows that and more. Doesn’t talk about porosity but it can help with it and few other things. “How to strike and arc & restart” th-cam.com/video/mEYgYhDd3-Q/w-d-xo.htmlsi=ltJ_luX78MPrVi6S
Hey man, would you recommend going to welding school for a 20 year old? I'm in college right now (with no debt because college is cheap where I'm from) but its going to take me 10 years to get a degree. I'm thinking of doing a trade job either permanently or just while studying. I think it takes a few months to get a welding license or degree where I am. Is welding a good career that you would recommend? or should I just stick to college and get a degree.
You can never go wrong doing welding there various ways and types and fields which would fit to anyone
@@LouHemi Thank you for the thoughts. I'm gonna think it over until the year ends and before my next semester starts.
Thanks for reaching out. I’ve seen students from 17 to 60+ years old! I started welding after high school. Very HOT, in the shop or outside, in Texas! I also went to college while welding & got my associates of applied science in welding. If you don’t mind the heat, sweating, working with your hands then welding might be something to look into. Different processes to learn which could land you in an air conditioned shop! Like stainless, chromium, aluminum or other exotic metals. Not sure what degree you are going for or what part of the country you’re in? Some schools or welding training offer short courses like 2or 9 months. Which is enough time to learn one processes (TIG, Stick, MIG) which could land you a job while you continue school. I’ve enjoyed my career in welding. I’ve also wanted to do it since I discovered it in high school & stuck with it. Welding is & always will be a trade in need! Maybe try welding engineering or technician? Best of luck, thank you for your time.
@@letitshinewelding3787 Thank you for taking the time to write such a detailed comment. I will definitely be considering it.
@@lawsen3719 I say the earlier the better im still in school right now about to graduate in 2-3 months so far im liking it. After my school im going to refineries with my dad which is not bad making 51$ an hr plus 120$ a day for per diem and travel pay and refineries aren’t like pipeline which you’ll always out on the open field
Very much enjoying your teaching style here. You're making a lot of great points that I haven't seen on other welding videos, and writing the pattern for the electrode tip on the piece (like the "G") is worth a thousand words.
That’s what it’s all about, brother. I pray that I say the right words, show a certain technique or angle that could help even one person. I’m happy to hear this helped you in some way. I will continue to post more videos. My next one is explaining a few ways of preventing undercut and how your puddle controls your speed! What do you think? Anything comes to mind? Have a blessed one. LET IT SHINE!
@@letitshinewelding3787 As an amateur I'm not the fellow to be suggesting topics to you, but that sounds like an interesting one. I think it's a bit unfortunate that style trumps substance a lot on youtube, but I'd just say to do your videos in a way that pleases yourself, and not compromise your personal style.
@just_a_quick_ride thank you for the input! LET IT SHINE!
Thanks mate! Realy some good arc shots and details which didn't saw elswere! Thanks for sharing and God bless you!
Your correct. I my instructor saw I was favoring Tig, so I spent my first year trying everything ,and my last year in the Tig booth. He had me welding aluminum boat parts for the Marine shop in our school. Right after school I got a job welding for a major airlines on titanium. It was easy to switch over, because all their machines were setup correctly for the type of parts they wanted me to weld. I just sat down . and started welding, in an air conditioned shop making big money too.
That’s awesome! Eyes are on you when you least expect. Keep it up brother, LET IT SHINE ✨
A pipe is not a coupon is it
I learned a lot from this video, Thanks so much for making and sharing it! I’m stuck on 1G at the moment but my class is doing all this pipe fitting, hand beveling and welding up pipe, some even further along than that. I have to work on my tie ins and figure out how not to have so much metal buildup at the bottom of my plate, keyhole issues etc , all the beginner mistakes, but my notebook came out at 11:00 minutes mark and It was speaking directly to my issues i feel! Gonna try it out and see if it applies to my 1G with no back strap. You covered 2 weeks of schooling in 30 mins 💪🏽. I can always look back on this video when I get there. So blessed to have come across your channel! 🙏🏽 You’re an amazing teacher by using mistakes you’ve seen others make and by thoroughly addressing how to do things in detail which I feel a lot of great welders don’t do because they’re so good they forgot how beginners think and understand stuff. Please keep making these videos 🙏🏽👏🏽, You’re amazing! 💯🤙🏽💎 God Bless Brother!
Thank very much for the comment! I’m happy this helped, I will continue to pass the experience and knowledge 🫡
a video of the basics of tig welding
I have an aluminum TIG video on the channel also, check it out. I will definitely post a TIG basics video. Thank you for the request.
🔥🔥
Big ass gap with 3/32 filler is ballsey