วีดีโอ

aap coupler ko amazon flipkart ya koi aur site se mangwa sakte hain. youtube coupler nahi bechta hai. aap google par search kijiye "bullet mixer grinder coupler" aapko bahut option mil jayenge. apne area ke kisi electrical shop se bhi kharid sakte hain.

thanks and welcome

check electrical connection, condensor, and motor coils

charge ho raha hai ?

kyu bhejna chahte hain? kya problem ho gaya hai?

It supplies power to the UV lamp only when the green light on the PCB lights up. Usually the red light on the PCB flashes when the water storage tank is full. When the water level in the storage tank drops the water level sensor gives a signal to the PCB and then the PCB turns on, also do not check the voltage on the UV lamp connector, it can be dangerous.

thanks and welcome

thanks and welcome

Actually that fan is used to cool the motor while running. Since the motor is high speed, it produces more heat. If there is no fan the heat generated by the motor may burn out the motor coil. So it is better to change it. If not possible, run the blender for a very short period of time, wait for a while to cool the motor and then run it again i.e. use the motor intermittently.

Plzz rly bother

Actually that fan is used to cool the motor while running. Since the motor is high speed, it produces more heat. If there is no fan the heat generated by the motor may burn out the motor coil. So it is better to change it. If not possible, run the blender for a very short period of time, wait for a while to cool the motor and then run it again i.e. use the motor intermittently.

Tqqq somuch brother.where should I repair?

yes

@@diyrepairs Thanks for reply...

Can you tell the exact problem? Actually the machine is very simple. It has a heating rod that heats the surrounding environment. To control the surrounding temperature, a sensor is installed in it which gives signal to the control circuit. If the machine is not heating properly, check the sensor and control circuits.

check connection, value of resistance and polarity of transistors.

mere video hindi aur english done me hain. kripya hindi wala dekh len. Thanks

Thanks and welcome

900 va inverter me transformer ka winding bhi 900 va ka load lene ke liye bnaya jata hai. 700 va circuit lagaya ja sakta hai lekin load 700 va se jyada nahi dena hoga.

@@diyrepairs mera excide 900va pure sine wave ka inverter kharb ho gaya tha to company waalo n circuit change kr diya abhi work kar raha hai lekin load Dene se LED bulb blink krte hai , to mujhe doubt ho raha tha ki kya unhone 700va ka circuit to nhi laga diya , Transformer wagera change' nhi kiya hai bass circuit kiya hai ,

@@habibiedits1565 900 va ka matlab hai 900 x 0.8 = 720 watt. 720 watt ka load dekar check kar lijiye. waise company ka service engineer aisa nahi karega.

The video is real. If your pre filter is fitted tightly then use a hammer to open it, tap the top cover with the hammer in a counterclockwise direction.

Yes exactly my pre filter is quite old. Thank you so much for guiding :)

@@pawan2038 welcome

thanks and welcome

check the heating tube and its connecting wire for short circuit. if it is good then increase the value of fuse.

If TDS of outcoming water is 11 then why are you changing the filters. Simply increase the TDS to the desired value with the TDS controller valve. You can watch the video on TDS controller from RO water playlist.

​@@diyrepairshi, I have the same model, recently this beeping issue came up and the kent engineer is asking 5500 rupees for all 5 filter change, after watching your video I arranged the carbon and sediment filter online since my TDS is under 200 (right now 46). I could've done it myself but since my filter was under free service warranty, I thought to get it replaced from the kent engineer itself. But as soon as that engineer came, he told us that the beep sound ONLY comes when ALL 5 filters start malfunctioning and I must replace all 5 filters at once. To get a second opinion I contacted the urban company person also, this person also told me to replace all 5 filters at once. He mentioned that this machine is designed in a way that you must change all the 5 filters. Please let me know what to do. If you're sure that the beeping (&TDS) issue will resolve with changing only these 2 filters (i.e sediment and carbon filters) please let me know, I will do it myself. I personally feel that this 5500 thing to be a total scam and not worth going for.

video main hindi aur english dono me upload karta hoon aap playlist dekh lijiye.

@@diyrepairs thanks sir ji 🙏🙏

thanks and welcome . main koshish karunga.

It is pre sediment filter and its price is around Rs 70 to Rs 250 depending on the place and quality. Check online or find a shop that sells RO spare parts in your area.

wah push buttom hai kya? overload protection ke liye diya rahta hai. usko daba kar dekhiye. machine ke andar fuse hoga to wo bhi kharab ho sakta hai.

Nhi hua kuch return krna pdega

Agar mil sakta hai to please mujhe link send kr den

kaun sa spring jo jar lagane par switch ko niche push karta hai? service center me chek kar sakte hain ya kisi purane pen ka spring agar mil jaye to laga sakte hain

Ji bhai

Yes why not, we can use lithium ion batteries.

service center

paani ki wajah se mop par frictional force lagta hai. aur dryer me nahi lagta hai. mop kahin se jaroor loose hai tabhi dryer me ghum raha hai aur paani me nahi.

spin bucket rod ke naam se milna muskil hai lekin motor banane wale dukan me aap try kar sakte hain. bahut saare motor ka rotar me jo rod laga hota hai isi type ka rahta hai.

Why are you using 400 GPD RO membrane?? The value of flow restrictor for 400GPD membrane should be 3150 mL.

Thanks and welcome