Bad Dad Joke Mechanic
Bad Dad Joke Mechanic
  • 8
  • 90 487
2015 Ford F150 Code P0620 Service Charging System
2015 Ford F150 5.0L setting code P0620 for generator circuit and displays service charging system on dash.
3 pin connector at alternator:
Pin 1 - Vio Gen L1
Pin 2 - Blu/Org Gen RC
Pin 3 - Batt voltage from fuse 30 10amp in BJB hot all the time, this needs to be load checked.
Pin 1 Vio goes to pin 26 in connector C1381B at the PCM
Pin 2 Blu/Org goes to pin 13 in connector C1381B.
When looking at the PCM connector C1381B is on the right hand side, I marked with blue tape in picture and marked pins in black on connector.
มุมมอง: 354

วีดีโอ

2010 Ford F150 Code C1278 Steering Rotation Sensor
มุมมอง 97610 หลายเดือนก่อน
2010 Ford F150 5.4L setting ABS code C1278 for steering rotation sensor 1 & 2 signal fault. Replacing steering rotation sensor. Sensor connector pins out as follows: Pin 1 - Grn/Vio Ground Pin 2 - Gry/Brn 5V square wave Pin 3 - Vio/Org 5v square wave Pin 4 - Gry/Blu Battery voltage Steering rotation sensor part # is: 9L1Z-3F818-A
2014 Lincoln MKZ Mode Door Actuator HVAC Replacement And Steering Column Removal
มุมมอง 2.5K10 หลายเดือนก่อน
Replacing HVAC mode door actuator in a 2014 Lincoln MKZ. HVAC was stuck on panel would not move to floor or defrost.
Clay Sky Ski 2021
มุมมอง 453 ปีที่แล้ว
Clay Sky Ski July 24th 2021 Coralville Lake Iowa
2008 Pontiac G6 Theft Deterrent Module and Ignition Switch Removal
มุมมอง 68K5 ปีที่แล้ว
Replacing a theft deterrent module on a 2008 Pontiac G6. This module does need to be programmed with a GM Tech2 scan tool and if the module is dead and unable to communicate you will need to cut and program new ignition keys, you will not be able to reprogram old keys into a new module.
2009 Kia Rondo Rear Door Handle Base Replacement
มุมมอง 18K5 ปีที่แล้ว
Shows how to remove rear door panel, window regulator, door latch, and door handle base on a 2009 Kia Rondo. Note: You do not need to take the two screws out that hold the interior door handle to the regulator as I say to do in video. you can leave inside door handle in place if you are just doing latch or door handle base. Part numbers are Left Side: 836551D000 Right Side: 836651D000
Hydrofoiling summer 2017
มุมมอง 226 ปีที่แล้ว
Hydrofoiling summer 2017
Maytag Gas Engine 72-D Twin Cylinder
มุมมอง 2316 ปีที่แล้ว
Maytag 72-D Twin cylinder gas engine

ความคิดเห็น

  • @Jonnn21
    @Jonnn21 หลายเดือนก่อน

    There has GOT to be a better way to get to that

  • @sixtovigilancia4825
    @sixtovigilancia4825 2 หลายเดือนก่อน

    i need to fix wiondow elevator. i had a difficulty of removing the door panel. now I know, thanks a lot man.

    • @dmv3607
      @dmv3607 7 วันที่ผ่านมา

      You're welcome! Thanks for watching happy to hear it helped you.

  • @GWGarage.
    @GWGarage. 4 หลายเดือนก่อน

    I was trying to figure out where it was and wondering if i could calibrate it without taking the truck somwhere thanks alot! 😊

    • @dmv3607
      @dmv3607 4 หลายเดือนก่อน

      You can try to manually calibrate by rotating steering wheel all the way to the left then all the way to the right a least two times, if that doesn't work then you will need a scan tool to calibrate.

  • @josephdiaz1577
    @josephdiaz1577 4 หลายเดือนก่อน

    How did you get the bottom panel off that's under the steering Column??

  • @WesternReloader
    @WesternReloader 5 หลายเดือนก่อน

    Yikes. Just got a 2010 MKS, AC blows cold, but it’s stuck in defrost mode… shiit

  • @user-tv6zz1vm3x
    @user-tv6zz1vm3x 6 หลายเดือนก่อน

    Great video. Thank you for the help.

    • @dmv3607
      @dmv3607 6 หลายเดือนก่อน

      Happy to hear it helped. Thanks for watching and replying.

  • @Dubnot
    @Dubnot 9 หลายเดือนก่อน

    Great video and well explained. These cars are weird with little available information online. Ive driven it across country 6 times. Figured i might as well keep it alive for a bit 😂

    • @dmv3607
      @dmv3607 9 หลายเดือนก่อน

      Thanks for viewing and the feedback!

  • @pennymyers6838
    @pennymyers6838 10 หลายเดือนก่อน

    After doing all that my battery wont hild a charge, nee battery

  • @tonyfreeborn6766
    @tonyfreeborn6766 ปีที่แล้ว

    Great video,very clear instructions.Thanks for sharing the knowledge.Saved me a lot of guessing and swearing👍

    • @dmv3607
      @dmv3607 9 หลายเดือนก่อน

      Thank you for viewing and letting me know it helped you!

  • @montmib
    @montmib ปีที่แล้ว

    I would like to see you doing it why do you need to play in the window?

  • @brucehohl5918
    @brucehohl5918 ปีที่แล้ว

    Thanks for this great video. Before disassembly, I was able to see that the pivoting striker part of the base assembly was broken by looking through the capped hole just above the child door lock. The break was the same as shown in the video. I was shipped the wrong part and did not want to wait for a replacement so I repaired the broken part by drilling two 5/64 inch holes through the plastic outer 'cylinder' and inner metal 'cylinder', inserted a 4d nail (cut to size) in each hole, 4-5 wraps of nylon string, plastic epoxy for the crack and nail ends, and glue to keep the string sealed in place. Hopefully that was overkill and fix will be permanent.

    • @dmv3607
      @dmv3607 9 หลายเดือนก่อน

      Thanks for watching my video!

  • @RodneyRenehan
    @RodneyRenehan ปีที่แล้ว

    Fella, I don't know how to express my personal thanks, for such an elaborated exercise. You did, absolutely astounding

  • @richardescobar7284
    @richardescobar7284 ปีที่แล้ว

    Do you replace the ignition module or leave it alone

  • @gosgraproperties8687
    @gosgraproperties8687 2 ปีที่แล้ว

    Thank you sir

    • @dmv3607
      @dmv3607 9 หลายเดือนก่อน

      Thanks for watching my video!

  • @zborgerd
    @zborgerd 2 ปีที่แล้ว

    Most useful video on the Internet. Had it apart and swapped out in just over an hour thanks to you. Now I can spend a few hours on my motorcycle on this beautiful day since the car is fixed. Keeping this KIA until it drops.

    • @dmv3607
      @dmv3607 9 หลายเดือนก่อน

      Thanks for watching my video!

  • @donaldthompson941
    @donaldthompson941 2 ปีที่แล้ว

    My door won't open, and I can't get to the 3rd screw. Is there a way to get the door open?

  • @robinnorman1170
    @robinnorman1170 2 ปีที่แล้ว

    How did you secure the window out of the way

  • @Mickeyy197
    @Mickeyy197 2 ปีที่แล้ว

    Your goal was to remove the ignition switch?… I’m afraid you need more training boss 🤦🏽‍♂️

    • @dmv3607
      @dmv3607 10 หลายเดือนก่อน

      As I stated in my video I was replacing the theft deterrent module.

    • @tuco673
      @tuco673 6 หลายเดือนก่อน

      ⁠​⁠@@dmv3607does the new theft deterrent module need to be programmed to the car or no?

    • @dmv3607
      @dmv3607 6 หลายเดือนก่อน

      @@tuco673 yes it needs to be programmed.

  • @calculatorcounter3437
    @calculatorcounter3437 3 ปีที่แล้ว

    Hi, I appreciate the video, I have removed my ignition switch in my 08 G6, but there is a black CABLE coming out of the back. It does not seem like it want to pull out even after depressing the catch. Any idea of what this is or how to remove it? Thank you

    • @Richuod
      @Richuod 2 ปีที่แล้ว

      try turning the key in the ignition

    • @ThaReelBA
      @ThaReelBA ปีที่แล้ว

      @@Richuod definitely turn the key, thank u that was my problem as well

  • @kilianagboton4229
    @kilianagboton4229 3 ปีที่แล้ว

    Thank you very much. This helps a lot. Many thanks

    • @dmv3607
      @dmv3607 9 หลายเดือนก่อน

      Thanks for watching my video!

  • @TheParasitick1
    @TheParasitick1 3 ปีที่แล้ว

    This guy. How obscure is an 09' kia rondo. Thanks for the video!

    • @dmv3607
      @dmv3607 9 หลายเดือนก่อน

      Thanks for watching my video!

  • @beavercountylibrarysystem8749
    @beavercountylibrarysystem8749 3 ปีที่แล้ว

    Really great video! 🙏

  • @captainamerica6521
    @captainamerica6521 3 ปีที่แล้ว

    sorry about all my comments trying to help people is all! this part is dealership only 63.00 bucks and they said they must do something to program it to recognize key and computer! probably hundreds! only other way i found is key forward ten minutes three times in many forums! autozone nobody carries this!

  • @captainamerica6521
    @captainamerica6521 3 ปีที่แล้ว

    autozone, napa, advanced all said they have no such part this is cunfusing! mine has code 1682 ing switch! and error on dash odometer says miles then goes to error! everything works no click no start! nothing replaced battery, alt, starter cleaned grounds traceed all wires. tried to bypass relay starter and it rolls over wont start! er er er! this must be a dealer only part with key needs programmed! hundereds and hundreds at dealer and you still tow car home! the company should reemburse every dummy with this piece of crap made car!

  • @captainamerica6521
    @captainamerica6521 3 ปีที่แล้ว

    i ordered a switch do i need to order a theft deterent also! ???

    • @AaronRowland-y5w
      @AaronRowland-y5w ปีที่แล้ว

      So what happened to your car did you have to order a new theft

  • @captainamerica6521
    @captainamerica6521 3 ปีที่แล้ว

    i think the ignition switch on this car goes to bcm not the pcm! these cars are nightmares gps tracker, onstar, sterring computer thingy all fail cause no start issues! hidden starter linkable fuzes impossible to get to, gm used cheap china wires all crack and melt snow and heat effect these cars!! greatly!! starter is next exust manifiold lol practely touching heat makes starters not work after use! wont start till cools down! these cars are basically push button start! only thhey use a key you turn forward and release immedetely car will start! if all is good! people who crank these key forward until starts and blow linkable fuze, it has like 9v always going to it theres two sources of power to start these cars! second source gives fast, quick start 12v energy. after starts relays close secondary power source! if you hold key forward you can burn any g6 to ground! the wires get hot melt smoke fire boom!!!!! all these cars have oil leaks in this trouble area! up by exust manifold! car was wired by blind, jewish, african, pollocks! theres a factory installed spy device onstar! reports your speed and daily driving if seat belts on ect... im a dispatcher and dealership hiden gps trackers all can turn car off sometimes these dvise fail and shuts off forever! nobody ever figures it out!

    • @dmv3607
      @dmv3607 10 หลายเดือนก่อน

      Yes as I stated in the video the theft module sends the signal to the BCM which then sends the signal to the PCM to allow the vehicle to crank and start. Thanks for watching!

  • @strayboogie5833
    @strayboogie5833 3 ปีที่แล้ว

    Will this give you error message if this part is bad? My car keeps going into anti theft mode reading error on dash.

    • @ashleylara7072
      @ashleylara7072 3 ปีที่แล้ว

      Did u fix yours? I have the same problem

    • @captainamerica6521
      @captainamerica6521 3 ปีที่แล้ว

      mine too! lmao

    • @SantanaTheFurst
      @SantanaTheFurst 5 หลายเดือนก่อน

      @@ashleylara7072did you find out?

    • @SantanaTheFurst
      @SantanaTheFurst 5 หลายเดือนก่อน

      @@captainamerica6521did you find out?

  • @ELAMRI9
    @ELAMRI9 4 ปีที่แล้ว

    Good job

  • @BaRS_flint
    @BaRS_flint 4 ปีที่แล้ว

    You just removed the entire dash to get to the ignition? Doesn’t seem right to me

  • @shaunfrench75
    @shaunfrench75 4 ปีที่แล้ว

    Alright what was going on why you removed it... I'm having a problem with my G6 it turns but wont start some times and just randomly dies out any time.

  • @علياحسان-ذ2ث
    @علياحسان-ذ2ث 4 ปีที่แล้ว

    Ineed help ineed key switch impolisar my car Pontiac grand Prix g6. 2008 you can help me with my car

  • @coreydraper8227
    @coreydraper8227 4 ปีที่แล้ว

    Would that make my car shut off while driving then not start anywhere from 15mins to 40mins

    • @captainamerica6521
      @captainamerica6521 3 ปีที่แล้ว

      no unless you have many keys or to much wieght on key chain! these cars gm you cannot put anything on keys it messes the tumblers up. your issue is most likely starter its next to manifold gets hot many people have to put a heat plate between them. when starter gets to hot it wont start until cools and cant take to much punishment never these pontiacs idol long time ever! they over heat, leak everything, and starter issues and theres a hidden wire above starter green linkable fuse can go bad work then not work! impossible to change almost! run new line! easyiest!

  • @dangeroustoys5668
    @dangeroustoys5668 4 ปีที่แล้ว

    Thanks for the info on how to this, the regulator broke on my 2007 kia rondo and i couldnt figure out how to get the panel off or release the glass w/o breaking everything. Btw the dealer quoted me $350 for the window regulator assembly and another $375 for labor. I bought the regulator and also needed a new motor , that cost around $200. Watch the metal edges, theyre sharp .

  • @chuckturner8155
    @chuckturner8155 4 ปีที่แล้ว

    If you replace the igntion do you have to flash the computer?

    • @ndm.8521
      @ndm.8521 4 ปีที่แล้ว

      No, but you will need to do a Passlock relearn. Here is one of the websites that has instructions: newrockiesinc.zendesk.com/hc/en-us/articles/231568207-2005-2011-Chevrolet-Malibu-Saturn-Aura-Pontiac-G6, scroll down to where it says '30 MINUTE RELEARN PROCEDURE'.

    • @AaronRowland-y5w
      @AaronRowland-y5w ปีที่แล้ว

      What happened was you able to figure it out

    • @ultimateormus7903
      @ultimateormus7903 หลายเดือนก่อน

      ​@@AaronRowland-y5wI think you have to do a key relearn by turning to on but not start for 11 minutes and then off for 30 seconds for a total of 3 times and it should relearn the theft by pass code

    • @AaronRowland-y5w
      @AaronRowland-y5w หลายเดือนก่อน

      @@ultimateormus7903 I'll try that

  • @meskinthug5577
    @meskinthug5577 4 ปีที่แล้ว

    I just replaced mine, the car started twice and now it is not cranking.

    • @AaronRowland-y5w
      @AaronRowland-y5w ปีที่แล้ว

      Did you ever figure out what happened of why it wasn't starting

  • @316hit_the_gas7
    @316hit_the_gas7 4 ปีที่แล้ว

    Why did you take that out? What was going on with the car?

    • @dmv3607
      @dmv3607 4 ปีที่แล้ว

      The module was bad and vehicle would not start.

    • @316hit_the_gas7
      @316hit_the_gas7 4 ปีที่แล้ว

      DMV360 well I know that. Like what lead you to replacing that??

    • @dmv3607
      @dmv3607 4 ปีที่แล้ว

      @@316hit_the_gas7 Vehicle would not start due to theft module being bad, no communication with module. Tested power and ground to module and data line was good.

    • @dmv3607
      @dmv3607 4 ปีที่แล้ว

      @Tyler Mulkey Because the theft module was bad

  • @goodvibes6038
    @goodvibes6038 4 ปีที่แล้ว

    I opened doors belts but this was weird

  • @goodvibes6038
    @goodvibes6038 4 ปีที่แล้ว

    Thanks man, this helped alot

  • @bigjock7691
    @bigjock7691 5 ปีที่แล้ว

    I have a kia rondo the door will not open at all out side or inside ,how can I get the door open without damaging the door card.

    • @neiltheplayer
      @neiltheplayer 4 ปีที่แล้ว

      slide the inside panel up and off after removing the 3 screws, you will need to pull the panel away from the door before lifting off and push the child lock down/back towards rear of vehicle after removing the interior panel. you should be able to use the inside door latch to release door

    • @MrFreshchico
      @MrFreshchico 4 ปีที่แล้ว

      @@neiltheplayer that's good advice.. thumbs up.

  • @mb1470
    @mb1470 5 ปีที่แล้ว

    My alarm went off and now it won’t turn over or anything. Completely dead. I disconnected battery and even changed computer to see if that was it and no luck. Any ideas what it could be?

    • @jaydenbillings842
      @jaydenbillings842 4 ปีที่แล้ว

      You have to get the new computer programmed to your car bro

  • @MegaBraunie
    @MegaBraunie 6 ปีที่แล้ว

    HOOOOLY SMOKES!!!!!!!!!!!!!!!! WILD!

  • @manticcoins8940
    @manticcoins8940 6 ปีที่แล้ว

    wow, i wouldn't mind being as mechanically capable as you, where's the keyboard ;) Thank you for sharing!