- 12
- 23 663
Two Stroke Neophyte
เข้าร่วมเมื่อ 16 ม.ค. 2013
วีดีโอ
Yezdi Roadking gearbox 6
มุมมอง 1.6K2 ปีที่แล้ว
Correction: the actual numbering of the gears as per the notches is exactly opposite to what is shown in the video. Irrespective of the order of the gears, the cam plate is symmetrical. if this is a 350 camplate then the numbering is correct.On the jawa 634, and 638-640, the shift pattern is opposite(one down and 3 up) to that of the 250cc.
Brother, please share your contact information or contact me. I really appreciate what you are doing. I think we both can benifit from each other. Just please contact me once, atleast see what I am offering 🙏
Brother, please share your contact information or contact me. I really appreciate what you are doing. I think we both can benifit from each other. Just please contact me once, atleast see what I am offering 🙏
You can cut off the septum in the boost port section for getting enhanced performance.
Nice
Hey man! i was trying to open my yezdi cl2 engine. can you tell me how to remove the magnet/rotor? do i just need a bearing puller?
How much cost to do this?
Have gone further with the design,, now has a rx 135 reed valve case
@@twostrokeneophyte7724 can u sent your insta id i will dm
Pls make a video on it, and what will be the approximate cost to do all that.
Useful information
3rd gair not working properly please solution
Ported max r 100 topspeed kitna hai
Hi sir.. Can we do the similar to Samurai cylinder also? Can you please mention the breadth and width in mm?
Yes, both cylinders are same but i have seen difference of plus minus 5 degrees between bores, an average figure is 110 degrees transfer and 150 degrees exhaust. If you keep transfer and exhaust stock then no point increasing intake. 8291751709 for more info.
@@twostrokeneophyte7724 bro your contact number?
Does the performance increases?
Yes, more inlet area. You have to increase port timings to get max benefit from it. Earlier only two reed petals were active now all three.
another boost port ?
Yes, a pair of auxillary ports
Please send मोबाईल मोबाईल number
8291751709
Bro your contact please
8291751709
Bro contact??
transfer port size increased ?
Yes,, both width and height
Whats different?
See carefully bro.
Very nice explanation... Thanks a lot...!!!
Nice explanation. 👍
Awesome
nice
Very informative video....
awesome
keep it up
good content
Aano??? Sho!!!
@@twostrokeneophyte7724 sathyam
wow very informative
Taiming chen chahiye ser
Excellent series of videos, compliments to you sir.
Thank you for your appreciation.. There are more videos which will be added soon.
Upload Full Engine Setup alon with Gear box - Need Full engine assembly video
❤️🌹
Very good explanation dost
Very nive
Very good experience
How to check changer plate is good or replace. Gier will change it will be strucked
Is there any particular gear in which it gets stuck? For Camplate check 1) play of camplate on the rivet. If ends of camplate deflect more than 1.5mm,change the rivet. Rivet size is M6. Dedicated workshops can replace rivet. 2) also replace spring and steel ball of locking gate. But camplate alone cannot cause these problems.
OK sir I will checked some time topgier struck some time first gier struck
@@sujinsuc4692 you can watsapp me on 8291751709.
@@sujinsuc4692 If you open your clutch cover check the path for the two shifting pins on the cam plate, if there is excessive wear/grooving on the pathway then the pins can get stuck in First and Top gear.
Problem solved thanks for your support. Another request deluxe statercoill available??
Informative video keep it up 👌👌👌👌👌
Thank you
Appreciate your explanation, this helps a lot to understand and correlate the gear shifting of our beloved RK, please continue to post more videos on Yezdi gearbox and help us understand more.