วีดีโอ

Nope Handtools only till this happened and No the owner Ran it to the dirt. Over 300,000+ but never spent any money only Gas. TIP If soaked over night with Petro this probably wont happen and Change the plugs before 300k😂

@@mrlocc9696 hello Thanks for stopping in. Great News 314,097 Still Rolling. It Doesnt like long drives or alot stop go at lights because transmission

This one Really is Right to it i never said a word the Sound is pure Fins. And the damage was not to bad this coil was a Hot water coil and the supply air temp was low when it had Hot water the coil was Clogged after the wash i was Showing new boots How it worked Because he enjoys Flatting them😮 Now he will learn. iv had a boss send guys to to this and say get it done guys using cards, Forks😂

crazy how phones do that.... pop them up. This task was on a older truck and was different for me becase i never have done this before i used high heat but kept in mind I didn't want to replace the whole shaft , rubber hammer socket and torch worked.

😂❤ Yeap i will Watch too or show how no more wires for me. 😢im a loner so i did commercial less people.

@@benchandler7089yeap most times a large bag is always to much and The brand has Held up still today Very pleased. i have seen any days guys full pack and carry it only needing small hand tools. Thanks for the sub 👍

@chargermopar Butane is Cooler anyways 😉 Thats Why Blue flame Cold.

🤯

Its not the manufacturers 😂 you are either a biden bot or really have no clue . In either case your a biden boy

These are Sweet i think. Wish People had them on there homes

Hello Thanks For Checking out my Short. I have made a test board before to help explain and help with low voltage problems but not like in class. only to tech iv worked with.

Hey, thanks for watching glad you enjoyed it.

@@joshuaalewis4842 Good afternoon, I hope this comment finds you well, I have a machine that is almost the same as the one you show in the video, I would like to do this exercise, I would appreciate your prompt response and if you have an email that I can write to you that would be perfect, have a great day

@@joshuaalewis4842 Good afternoon, I hope this comment finds you well, I have a machine that is almost the same as the one you show in the video, I would like to do this exercise, I would appreciate your prompt response and if you have an email that I can write to you that would be perfect, have a great day

Most times the coil falling is age so replacement is option not repair but some time can be

💯% The Line needed flushed it was under ground lines 100'+ feet in 8" pvc and what a pain. A co worker left vac over night and the leak was in the copper line like 1/2" an 1" or something like that in the pvc and a 45 was leaking and the pipes had water in it. 🫣😱. all this had been filled in Grass and plants who know maybe a tree coulds have busted the pvc an not sure what to say about the leak . If It's Under Ground Double . Triple Check it. This is a way to ruin tools and equipment hell even reputation.

funny... because its not safe to run out side with blade on

yes 👍 i think so i dont do anything inside the chamber but its cool to check out their pc setup too and that i check psi readings. 😢 This place has lost alot of $$$ due to Venting of helium because they fail to pm the chiller unit. and customers turning around because it shuts down so they cant complete scan it errors out $$$:again

@@joshuaalewis4842 yes it is i just saw. If you look closely on the left hand side bottom of the scanner you can see it says “magnetom espree.” The coldhead pump itself is at the top of the mri on the left but it’s hidden under the covering of the mri to protect it. Most MRI’s use 1,700 litres of liquid helium to keep the superconducting magnets cool. The liquid helium needs to be topped up periodically. I’m not an MRI tech but I wish i was.

Ac coil fin tool

iv never before but... ok let me find a wall to test it on. and i need some 10/3 i would use stranded.

😂 Sorry

It's Not up anymore. its out its free

Coil Comb. Not sure of this brand but i have used it a lot They all wear down. Try Hilmor here the model and different sizes HIL-T-400 - 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 20 FPI HIL-T-412 - 12 & 14 FPI HIL-T-417 - 16 & 17 FPI HIL-T-418 - 18 & 20 FPI.

@@joshuaalewis4842 sir oder amazan na flipkart

​@@joshuaalewis4842cost?

Whats up

I could give it a Try. Most manuals in German and metric is used but i would start with the two books install and operations Book are online easily found .

I replaced compressor #2 and am pulling a vacuum now. The system is split into 2 parts, compressor n filter side. Recovery had to be done from both sides, 2lbs compressor and 25 filter side. When recharging do I have to put back same into each side bc when system off the solenoid separates the 2, or all refrig in filter side and once started it will open and cycle through both???

@@MRSTAR80 Yes Two Side. Low an High

@@MRSTAR80 because scrolls have discharge check valves , Systems should be charged both high and low sides simultaneously to assure ref. PSI is in comp before starting it. majority of charge put into the high to prevent bearing washout best if only vapor into the low side. 😉 GoodLuck

Your a year late bud

🤯🤷

No, Its a Hospital kitchen

Yes Roof Over Most of it But like 10' Above it. an your right a Short Roof can affect the Fan motors.

in my case its h2o so water would leak. This one has been removed so its Inlet an Outlet pipe was removed water with a hose flush in both sides cleaned the coil because it was for Hot water for a heater an was Covered real bad with Growth after it was washed then i also used This tool to fix it as best as i could. I Found it to be Oddly Satisfying 😆. If its for a Home ac system an your outside coil that tube would probably be High Pressure i would avoid getting a leak.

O hmm...

@@joshuaalewis4842 Thing is, last ac technician secured ac split evaporater to walls by pushing roughly and punctured one of those horizontal pipes. He said it was fine, no harm done. But I dunno... AC don't seem as cold anymore. Could just be me. I just wanna know if It will make me ill

Thanks for responding 👍

Yes. The Condenser fan was dead an the compressor tripped internal overLoad "OL". If you shut it down an give it time to cool Or Speed up that step with that device an was able to get it Going. After 5 min it Reset an was Reading Ohms after replacing the motor unit cools and didnt need new unit after All. I Also Have Used it For Recovery To Cool the recovery Bottle If i dont use My Coil Cooler for it.

😂 Well Time are Changing we are moving towards Microchannel AC coils... those are worse to bend back straight. This Coil Was Indoors an was 10 years old. It was a hot water coil.

No problem Thanks for watching! Its weird it was a high psi alarm code when its flat .

Power Of The Fist. 👊🏼

😭🥹 U think So? 💀