วีดีโอ

Bonjour, ne serait-ce pas un problème de batterie ?

@@yourfrenchtools7807 comment je peux le savoir ?

@@yourfrenchtools7807 car je vous explique un peut mon contexte , on me l’a offert mais une journée après je m’était cassé le bras donc je n’ai pas pus la conduire pendant un bon 4 mois , est-ce pour ça qu’elle a du mal ?ou aussi non je vais au travail avec et je prend souvent de nuit donc elle est dehors , serait-ce le froid qui l’a abîmé ?

Bonjour j'ai fait au mieux pour simplifier les différentes étapes, vous avez toutes les étapes pour réaliser cette opération. De plus, en commandant l'outil, vous recevrez une notice papier de démontage en 8 étapes !

Hello, I'm not too familiar with this scooter. If you take out the tube, you should see a toothed bolt which you can use for taking out and repairing the steering axle. Clement.

Узнал ? И какой же

I was wondering the same thing, but it's unlikely they will tell you as, quite reasonably, they want to sell tools. I was thinking of just putting different nut sizes down there and seeing if they fit, then retrieving them with a magnet but no guarantee that will work. Otherwise I'm going to try and find a detailed part list for the scooter somewhere and get the info that way.

@@vasvizsla Cool, thanks for that. I have been experimenting today, with a few trips the hardware store in-between, and have managed to fit an M10 nut in there (with some play) so its not perfect. I have an M12 bolt to try as well but I Have a feeling that will be too big, we will see tomorrow. My suspicion is that its an Imperial fitting, maybe 7/16" imperial size nut or around there as it would be the in-between equivalent of the M10 and M12 bolt (couldn't find an M11, I'm not even sure there is one!) Something I didn't mention is that I had to drill out the centre of the nut, removing it's threads completely to make enough room to get all the cables through, the cables, in my opinion, are the real pain in the butt in all of this! The negate the use of Box Spanners, as all the cables wont fit inside of it, from my experience anyway. So essay over, but we are making some progress I'd say, for the DIYers, I'll post here again if I get more success later on.

@@vasvizsla Good to hear your research has been going well too :) I have some info to share as well that you might be interested in. So I think we are right, I think the 18mm spanner size (thanks for that term, it gets confusing) is the right one, I messed with the 7/16" (17.46mm) size, which actually yielded decent results, there is a little play but it works. The first reason I stuck with it is, as we both discovered, M11 isn't really a thing, check out McMaster Carr and you hardly find a thing for it, at least not the conventual nut we are looking for. Second reason being I decided to try 3D printing, just to give it a go. So I designed a bit that would glue onto a hollow aluminium pole (18mm inner diameter 20mm outer). Printed it, glued it, let it dry for half a day and drilled two holed in the top for a bar to go through so I could twist with some torque.... Guess which broke first? The aluminium pole tore were the two holes and bar were, tore straight through! The print, on the other hand, showed some minor marks. Really I was quite surprised. So today I picked up a steel pole (17mm inner 20mm outer) bit tougher, redesigned the printed part am gluing it as we speak. We will see what happens, I'll give you an update when I know more. ps. Nice chatting about this 🙂

@@vasvizsla Jealous you have a welder! Tell me how it goes when you get it done, but yeah hopefully we are on the right track towards fixing our scooters. cheers!

@@vasvizsla Great news! It sounds like we have the same outcome, but reached it in different ways. I also have the small residual wobble but, like you, its way way better than before. About that movement, I noticed that the bearings themselves had a little movement (mine were the sealed kind, hard to grease) not much but a little. And on top of that I noticed that the hex shaped bar that slides into the main body (the bit that is attached to the wheel and moves up and down with the spring) has a bit of play. resulting in slight movement in the wheel itself but does not translate to the handle bar. In case you are interested, as I don't have access to a welder or even the ability to braze. So I decided to make my own tool by glueing a nut, about the same size as yours, to the end of a 1/2 inch plumbing pipe, found at the local hardware store, and filed down the pipe using the glued on nut as my guide. Got it to the rough shape, removed the guide nut and it worked, believe it or not! I did put some locktight on the loose nuts when I reassembled so I really hope that increases the amount of time I need to do this again! Anyway, thanks for the update and happy riding! ps. really need an extra battery for it though.

😊😊

6:56 6:56 😊

Hello, you never fold your scooter? Did you fixed it ?

Bonjour, Je ne trouve aucune commande qui se rapprocherait de votre nom Merci de me contacter par mail afin que j'examine l'incident qui s'est produit avec votre commande Nous trouverons ensuite une solution à ce litige

Hello, thank's ! Due to the câble, you can't use a box splanner

Take his word for it, It doesn't work, like he said, the cables get in the way. Shame as it would be an easy fix!

Hello, in my case, the thread locker is red but not as hard as the official red by loctite

@@yourfrenchtools7807 hi! got that. when repairing a motorcycle fork, I encountered a problem associated with a red retainer. I had to warm the hairdryer to unscrew the bolt (400 degrees Celsius).

@@yourfrenchtools7807 my bottom backlight is off. you don't know what it might be?

I really appreciate your comment, thank you !

Hello, You can find the links here : Ebay www.ebay.fr/itm/203859338345 Amazon www.amazon.fr/dp/B09XVM2X1R If you want a discount, contact me at ninebot.tool@gmail.com Regards, Clément

Pourriez-vous être plus précis ?

Hello, Thank's for your comment ! This video is aimed at a large audience that does not have the tools/skills to modify their scooters The first solution usually does the job for most people

@@yourfrenchtools7807 IT IS A LOT EASIER THAN THIS WAY, YOU ARE TELLING PEOPLE TO REMOVE THE 4 STEM SCREWS ON YOUR VIDEO, AL THAT IS NEEDED IS A 6MM HSS DRILL BIT AND M6 BOLTS THAT GO ALL THE WAY FROM ONE SIDE TO THE OTHER AND 2 NUTS EACH BOLT ONE ACTING AS A LOCK NUT, DRILL HOLES TO 6MM AND POST BOLT TIGHTEN, PUT TOOLS AWAY AND GO FOR A SAFE RIDE, IT IS ALUMINIUM SO THESE SCREWS THAT ARE USED ARE NOT THE BEST, GOING BIGGER WITH A BOLT MAKES IT WEAKER LESS THREAD TO GRIP, A THIN FLAT BAR ACTING LIKE YOUR TOOL AND GRIPS WILL SAVE HAVING TOGET A SPECIAL TOOL

@@1Saltyone Not everyone is able to pierce their scooter, and this is not the only problem with the play in the stem

do you have a photo of the stem to share?

Hello, Thank you for your comment ! Glad you were able to fix your scooter

Exactly, unfortunately I don't work for them

@@yourfrenchtools7807 just saying

Merci beaucoup pour votre commentaire, j'ai récemment sorti une nouvelle vidéo plus claire et précise sur cette même chaîne TH-cam qui devrait vous intéresser

Sono lieto di sapere che questo video vi ha aiutato

Hallo, Sie können mir direkt eine E-Mail schicken an: ninebot.tool@gmail.com Ich biete die Versandkosten für Kunden an, die das Tool direkt bei mir kaufen. Die Versandkosten für Länder außerhalb Frankreichs betragen 13€. Mit freundlichen Grüßen, Clément

Prego !

Bonjour ça peut venir de plusieurs choses mais généralement c'est l'amortisseur avant qui fait beaucoup de bruit. Il faut essayer de le bloquer

Muchas gracias por su comentario !