วีดีโอ

Where did u find the pump I can't seem to find both sides...

If one side does and the other doesn't. Probably time for new front shocks

How long did they last?

Got to do this today

There's no vent slots by the wipers, sweet car but definitely rough

Take a drill and open up the holes. The ripples in the bends are caused by a serrated bend die. That's used to limit the bend reduction on the inside of the tube. Their endforming skills are lacking.

That was nice but with the rear window, what are these clips you keep taking about and where do they go? What do they look like? How do you reinstall the chrome molding ?

Was the problem a coil pack at the end?

it could be ignition switch , ecm relay, dirty battery cables , bad battery , starter and if you go to a mechanic they will change them one by one.. lol

Thanks for the video. I watched the video several times. How does that weatherstrip on the that glass cone off and on? The weatherstrip on the edge of that chrome piece. I hope you can let me know. Thanks

Sorry, no. Doc appt. early, supposed to rain tomorrow and Tuesday. Thank you helping yesterday.

Listen I have a 2001 Nissan maxima. The fuseable link box broke. It’s 100$ on eBay. No no. So I hooked everything up up As if I had a link and it cranks but won’t stay idled. Battery good. I do have an inhibit relay on the way .. however only code I get is idler control Valve. The fuse never blew. It crumbled. So I got a numb if copper wiring just w zip ties so rigged. What to do.

Very helpful! Had the same issue!

I use a ramp and C-channel iron and drive my truck onto the ramp. Using this method, you might break the rim.

What number is that engine oil sensor part which one works for the Chrysler 300 5.7L

My only problem was finding out where the heck it was. Now that I know the location, I can hopefully replace it without too much trouble.

Where did you order your parts from?

How did you seal it shut?

"Tabby"?!?!?! 😂😂😂 im GONE✌️

My issue is pulling them out of the truck to clean I end up dumping dirt and debris all over inside of the floor anyway. They are to ridged or firm to remove easily

You complain too much

This showed me nothing 😢

I broke down and bought a tire bead breaker. Works great..... Love how you told about the tube direction...

Hi I have dodge charger and just replaced primary fuel pump.. But today while putting petrol all the petrol got leaked from down due to over flow but in the indicator petrol showing less so advice what is the cause?

M

I didnt see your video until i removed the whole thing now it says no ven is there anything else I can do

You were the actual only person on TH-cam that new what you were talking about or doing

I remember doing the rear window reg repair on my 67 GT Dart years ago thinking 2 hours. 8 - 9 hours later I was done. That was just one side.

Any updates on this issue same thing happening to my 2006 pathfinder 😢

I thought crankshaft sensor was leaking after removing starter there is no oil coming from the sensor nor have i had any trouble but a oil leak the sensor should i replace it why i got the starter out or just reput the starter back in please let me know ...But i think the leak is coming from little holes in flat bottom of the oil pan like the pot metal rusted little pits holes but small little holes is that possible please someone respond

Hey bud you should have disconnected the shift cable on the trans shifts easily by hand on shift lever no key in the ignition issue.

These mats have been best ones I've purchased. Had them about 3 yrs in my 14 silverado front and rear. They kept shape and still look great. Fitment and durability has been better than the weather techs in or other vehicles. I'm about to order for 24 silverado 2500hd.

You are doing a good job, nobody knows it all. The way you learn is get in there and do it. You did a great job on this video, very helpful. I'm working on a 2005 stang convert able 4.0l. Got abs and TC lights, code said rr ss not working, put a new one in and didn't help. I used your wiring diagram today to check power and ground to abs module, that's all good. I have to trace rr ss wiring and see where I'm losing signal. I know what little info I have found the 05 is a stand alone year for several fuses and wiring. Always an adventure, the trick is, not to be scared to learn. Thanks for posting this very helpful. 👍👍🏁🏁

The part number you listed (487500M010) ebay says it does not work on my 2004 titan. Is yours a titan? Im confused.

Pure genius! I've got one. Thank you for sharing!🤗

Where did you buy the spark plugs

Ok

Guessing this never got fixed?

It's your mistake

They are a bugger to replace! Even with the big C-clamp.

Do you happen to know the coil spring number that was used ?

Get the clutch and bearings kit very trick repair take the transmission out and carefully replace each friction plate build a long wooded table line them up and install the new clutches in sequence

This was very helpful. Thanks!

Thanks a lot for this video

Dealerships charge $1500 and it cost $200 to do it your self? Wow.

Well done Sir, You do it as a Pro. 3:32 yes those marks done by the QC in the factory... Great video 👍💯

Worst tutorial ever 😢

You bought the wrong size dude😊

Mine is doing the same thing and i changed the part and it's still leaking from the same exact place.what have i done wrong? can someone help me out?

I was on the the same side as everyone commenting below, Got mine installed at the tire size I've always gotten from the oem size and they are "ballooned" a bit. These were totally built for curb protection in mind. Still kinda new under 50 miles and cold out so I can't get a good feel of them yet.