- 5
- 27 003
Grumpy DIY
เข้าร่วมเมื่อ 23 เม.ย. 2018
HUNTER X-CORE Simple Program and Set up Explanation
Basic setup of 4 ports on a Hunter X-Core.
Mainly so I remember how I did it, but also to help others.
Mainly so I remember how I did it, but also to help others.
มุมมอง: 22
วีดีโอ
Cleaning 14 Years of grease from Kitching Units
มุมมอง 456 ปีที่แล้ว
During a kitchen refit, we wanted to reuse our cupboards while the new kitchen was being installed. We took the unit down and decided to show you how easy it was to clean 14 tears of grease from the kitchen units before we reinstalled them into the Utility room. Maybe you want to move the units to a garage for storage, or you want to sell them as used but good condition units, this video shows ...
Fitting Spot lights with Minimal Mess
มุมมอง 276 ปีที่แล้ว
I had to install 8 Spot lights in a kitchen and the wife doesn't like dust. I came up with this solution to keep the dust to a minimum.
How to Stop a Screw from Spinning - Life Hack
มุมมอง 4836 ปีที่แล้ว
Had an issue with a screw that wouldn't stop spinning. This is an easy and cheap way to resolve the issue.
Hayter Harrier Lawn Mower Hunting Revs fix and how to
มุมมอง 26K6 ปีที่แล้ว
My Hayter Harrier lawn mower developed a problem due to sediment in the fuel tank causing the revs to be erratic. This video will show you how to fix it for free and quickly.
Thumbs down because you don't answer your messages
1 thumbs down for you
Haha. I don't care. It's Bank Holiday weekend and I did the video to help people, not to earn money. And anyway, I'm not a mechanic, I don't know what it's called, but maybe ask a lawnmower parts shop and they will help you.
I now have rounded off the nut and the plastic O ring that sits on the nut has broken. Any idea the name of that nut and o ring or washer. Where I could buy a replacement part or the name of it please Thank you
Hi mate. I just done this but when I took the nut out the rubber that goes round the nut come out in pieces broken. So I need another rubber that goes round the gold nut. Any idea what it would be called to search for it online? Thank you
its for draining the fuel out from the bottom of the carb without taking the whole bolt out (that's why it has holes in the bolt) it would remove water from the carb as petrol sits on water. Any water in the carb would make it hunt. its not magic, just mechanics.
what is this mystery bolt with holes in? is it a jet? I have a similar bolt screwed into the carb on my 25hp outboard which the engine (sometimes) cuts out when clunked into gear. I cleaned the carb but it looked pretty good in there. is this bolt is the cause of so many running problems ? Cheers.
Thanks. Same problem and its working perfectly now.
Awesome. Seems to be a common problem with the quality of fuel these days. I have to do mine every year, and even mid season!
@@chorizo_uk There were some small particles of grit on the screw and washer. I blasted it all with carb cleaner and its as good as new!
Brilliant video mate! Had to de tune it after as I couldn't keep up with it in drive!!!!
Thanks great fix
great vid. Mine is the HH560D auto drive. Have the hunting problem but can't locate the fuel stop which I think isn't on my model or is in a different location. Do you know where it is? Thx
Hi ThePea. I'm not familiar with the model but it may not have a fuel stop/tap, in which case, you have a few options. 1. cut the pipe and put a inline tap OR if you can see the fuel pipe, maybe clamping with mole grips (with something to protect the pipe) OR disconnect the pipe from one end and block it with a bolt. Alternatively you will need to syphon out the fuel.
Is this process the same for a harrier 41 ?
Thanks a lot for this video, very helpful
That’s a great job
Worked thanks
Just done it thank you for a great tip ..
Mr Grumpy, please take a bow. You are nothing short of a Ledge! Thanks.
Thank you so much! This worked perfectly! Also a sewing pin worked to clean the holes
Brilliant, thank you, saved me a small fortune in going back to where I got it from. It worked a treat. Thanks once again.👍
Absolutely brilliant video, thank you so much for making this. My Hayter Harrier Pro was having these idle searching problems, as soon as you tried to cut the long grass it died. This is a 10minute fix that has worked perfectly for me. Thank you once more. 👍
cheers.....saved me min £40 sqid
This solution is still working, started briefly and cut out permanently stopped. Quick clean of the holes and float bowl and away it went!
Excellent!
I am going to try it....see if it works
Fantastic. It worked!! Good old You Tube!
Thanks very much for posting this. My Hayter Harrier (about 4years old) keep stalling when trying to start it. It would run for a few second then cut out. After watch the video I took the 13mm brass screw out of the carburettor cap and removed the cap. It was actually pretty clean and so no need for carb cleaner spray or anything. I poked a piece of wire through the hole in the screw and blew through it, then replaced the cap and screw. Mower started first time and is also now running great with more steady revs. It was the start of the season so I suspect there is some sediment etc in the fuel that was blocking things. Thanks again
a massive thank you for posting video. It worked. You star!!
Cheers thanks for your post I had same problem with my 5 year old 56 and it sorted it
Really glad it helped. PS. I seem to have to do this quite often due to letting the tank run dry and sediment goes through to the carb, so always top up the fuel before you start cutting :)