วีดีโอ

I turned on my car man i was squirting alot like a fountain no wonder i had a misfire

Very Cool !!!! Merry Christmas !!

Thanks. Question... Fuel line? 6AN? amazon? fuel filter line yes or no?....

Lock nut and adjustment screw 😊

You want to sell it, you have a very nice truck!

Check the bulb, then look at the socket to see if it's corroded and then check with a meter to be sure you have power inside the socket itself. Dielectric grease in each would be a good idea too. Good luck.

Thanks for posting , i got to do a vent window on a 51 soon . Is that 52 doors on yours? I like the push button open door handles ,wish there was a way to convert 51 to push button

Looks good, I'm been looking into carpets for my 52. Would you have the item number for that carpet by chance. Thank you.

No sound

did you place carpet under the carpet? Or did it come attached to the carpet?

Looks just fine man

Own a 54 too inside is up soon

damn! Nice progress!

Looks good to me. I am ready to do front and back glass on my 54. A little daunting.

Keep it up!

How do you start an engine when your carburetor is not hooked up and not primed?

Looking good, love those 3 windows.. See you next video...

If you have a infrared gun hit the exhaust manis if she is hotter than normal your lean😂

Looks good. Is that the original seat framing that you used or did you buy it??

Lube the pin before you put it in, this is why they wear out, no lube. Makes it alot easier to install with lube of some sort on it. The pin is supposed to be tight.

Mines a 54 these trucks are cool ,always looking for things to make better

I have a 1948 GMC. I'm working on it.

Nice truck. You have done a lot.

I tried it and my float was coming up and then it wouldn’t come up anymore

👍

My horn would go off when I turned as well. Same steering wheel setup. It was the female connector under the horn cap. Basically when I turned the wheel, the wire would ground on the column shaft bolt. I had to bend it almost straight, then a slight bend at the end. Worked like a charm, no more honking when I turn left or right.

Congrats my friend you’v being doing a lots of work on your beautiful project,it takes time effort and money but the end result is worth it thanks for sharing 👍🏽

Did you say start your engines? Your race ready dude

People of your generation don’t like old cars, am amazed Good job Man👍

Great work, I have enjoyed watching all the videos. Can you tell me where you got the patch panels for the lower front window corners or how they were repaired? Mine ate pitted pretty bad as well.

You've done a lot of work to your truck.. it looks really nice.. Are you located near Orlando FL? I noticed on your lic plate the first # was 6.. in the years past, that was the number of the county.. # 7 was Orange county.. #1 would have been the largest county ( either Jacksonville or Miami).. I loved in Central Florida for about 40 years.. Well enough about that.. You're doing a great job on your truck.. Thx for bringing us along.. Take care my friend...

my float screw won't stop leaking...tips?

Did you figure it out ?

Curious, did it fix your leak?

Sounds awesome!👍😎

There are auto paint stores that can match the original color and put it in rattle cans for you. I've done it several times for small spot repairs. The truck is looking great. Nice work!👍😎

Looks good, sounds good, love those old cherry 🍒 bombs.. I could hear my friend coming in his 57 a qtr mi away...

Good job

Use a big daddy rivet gun the mount the latch

What 4 link you using?

An old school Hemi would look great sitting between the frame rails.. BTW I love your truck... ...

What is this seat out of

I have been doing auto glass for years and that's exactly how I do it. Nice job

Water jacket. That's how you can drain out the Antifreeze from the block. Usually has a allen bolt, plugging it.

I wouldn't lower it anymore unless its bagged. So it would be more driveable.

Spot on so far

Sounds like a carburetor float issue.

Holley Sniper EFI FTW! Been running my Sniper unit since 2018 I love it

1st Bababooey. Lol...

I had the same problem. Mine was a fuel starvation problem in hard cornering the fuel pickup would get out of the fuel in the center of the tank. But only with half or quarter of a tank. Might look at that??? Took the tank apart and baffled around the pickup. Also put a lower section in the tank to sink the pickup lower into the fuel. Worked for me. My Chevelle never starved for fuel in a hard corner again.