A tip. If you ever get a problem with the high pressure fuel pump it is not sold as a separate spare. Have to buy the evaporator also and it get crazy expensive. But, you can buy the fuel pump to Johnson Ficht and it is the same. Only a different electric connector. Much cheaper :)
enverude i tec 60 hp 2012 model. Electricity comes on in one of the ignition coil when the contact is open .. I have moved the coils but it gives the same error again .. What can I do. If you have, could you please send me the service manual .. I think ecu is out of order .. I wish you good day .. ayhankucukozer@hotmail.com.tr
I had a 90 hp Evinrude when I was a kid back in 1964. Ran that motor on a 17-foot Thompson, skied with it, fished with it, camped with it. Changed the fuel pump diaphragm every spring, the lower unit lube every fall. Sold the boat and motor in 1984 and it was still running like new, despite who knows how many thousands of hours of use. Today's outboard motors are just too damn complicated, which is why they have so many problems.
Just saw your video , and you can have the injectors serviced coupled up and electricity pulsed and flushed.about 60 dollers each. This is for references, how it helps
So just what do you consider "normal injection"? Single-point injection? Throttle body injection? Port injection? Multipoint fuel injection? Sequential fuel injection?
I have a etec 90 down in south Florida. Switching to Yamaha. I've put over 4 grand into this turd. I bought it brand new with less then 5 hours on it in 2009. Just to much work. If you're looking to buy a etec keep looking cause it's not a good motor. Runs strong and hard but has a lot of starting problems and fuel system problems... trust I've been through it all this this turd
Hi i got the same etec never had a problem with mine Your problem sounds like your putting poor quality fuel or gas as you call it Put high octane in it clean out vapouriser and dont forgetvto blow out the tube on fuel system that collects the shit Then it will be bombproof
I've had my E-Tec for over 3 years so far and not even a hiccup. I know guys that have had problems with Mercury's. I know guys that have had problems with Hondas, and I know guys that have had problems with Yamahas too. I know a guy that had a 225 high-output etec that popped. Evinrude put a new powerhead on it and hasn't had a problem since.
I have this engine. Whilst parked over the winter season, the hydraulic tilt sensor triggered the tilt ram to run full up and continued to run until the batteries went flat. Cost to repair. Between $500 to $1000 for the hydraulic tilt ram, and one new battery. Warning , always disconnect your batteries if the boat or engine is going to have an extended layover.
Yep as you said we inspected the old fuel pump and it was most likely the old fuel in the pump. With the new pump I haven't had any issues, runs like a dream.
it overheats because the emm the brain is water cooled along with the high pressure pump/vst and injectors. its never a good thing to suck up mud any way it will destroy your water pump poppet valve and thermostats
Don't be like he said it was just the fuel pump. I fish professionally up here in canada and am not sponsored by evinrude in anyway but it is the only motor I will ever touch anymore. We bought an etec the same year our neighbor at the lake bought his merc four stroke and the dealer has already done 7 grand worth of work on his merc. Yes it was covered under warranty but a motor that's 3 years old and dealer maintained is pretty bad. There are more etecs in our tournament series then other brands combined!!
My etec engine dose that Same thing and then it turns of automatically and its full gas and water come out of the engine to cool the engine
A tip. If you ever get a problem with the high pressure fuel pump it is not sold as a separate spare. Have to buy the evaporator also and it get crazy expensive. But, you can buy the fuel pump to Johnson Ficht and it is the same. Only a different electric connector. Much cheaper :)
Hello
Hallo, woran hat e gelegen, was war das problem?
For sale?
enverude i tec 60 hp 2012 model. Electricity comes on in one of the ignition coil when the contact is open .. I have moved the coils but it gives the same error again .. What can I do. If you have, could you please send me the service manual .. I think ecu is out of order .. I wish you good day .. ayhankucukozer@hotmail.com.tr
to change the fuel filter there is a procedure or it is taken out and put the other
Where did you find a fuel pump for $180??
Looks like my 1988 Evinrude 48 special running on old fuel lmao.... And looks like it was exactly that.
I had a 90 hp Evinrude when I was a kid back in 1964. Ran that motor on a 17-foot Thompson, skied with it, fished with it, camped with it. Changed the fuel pump diaphragm every spring, the lower unit lube every fall. Sold the boat and motor in 1984 and it was still running like new, despite who knows how many thousands of hours of use. Today's outboard motors are just too damn complicated, which is why they have so many problems.
Just saw your video , and you can have the injectors serviced coupled up and electricity pulsed and flushed.about 60 dollers each. This is for references, how it helps
Direct injection engines isn't good as a normal injected engine
So just what do you consider "normal injection"? Single-point injection? Throttle body injection? Port injection? Multipoint fuel injection? Sequential fuel injection?
I have a etec 90 down in south Florida. Switching to Yamaha. I've put over 4 grand into this turd. I bought it brand new with less then 5 hours on it in 2009. Just to much work. If you're looking to buy a etec keep looking cause it's not a good motor. Runs strong and hard but has a lot of starting problems and fuel system problems... trust I've been through it all this this turd
Hi i got the same etec never had a problem with mine Your problem sounds like your putting poor quality fuel or gas as you call it Put high octane in it clean out vapouriser and dont forgetvto blow out the tube on fuel system that collects the shit Then it will be bombproof
I've had my E-Tec for over 3 years so far and not even a hiccup. I know guys that have had problems with Mercury's. I know guys that have had problems with Hondas, and I know guys that have had problems with Yamahas too. I know a guy that had a 225 high-output etec that popped. Evinrude put a new powerhead on it and hasn't had a problem since.
I’ve had my etec for over a year now, i bought it used, I’ve only had a few issues here and there but overall I’m very happy with it
I have this engine. Whilst parked over the winter season, the hydraulic tilt sensor triggered the tilt ram to run full up and continued to run until the batteries went flat. Cost to repair. Between $500 to $1000 for the hydraulic tilt ram, and one new battery. Warning , always disconnect your batteries if the boat or engine is going to have an extended layover.
I had a similar problem, I found my tilt switch jammed one morning, not sure how long it was running for, was a corroded tilt switch on the cowling.
Yep as you said we inspected the old fuel pump and it was most likely the old fuel in the pump. With the new pump I haven't had any issues, runs like a dream.
i want one but everyone ive seen come into our waters will not run more then a few hours all overheat if in shallow sandy or muddy waters
it overheats because the emm the brain is water cooled along with the high pressure pump/vst and injectors. its never a good thing to suck up mud any way it will destroy your water pump poppet valve and thermostats
Don't be like he said it was just the fuel pump. I fish professionally up here in canada and am not sponsored by evinrude in anyway but it is the only motor I will ever touch anymore. We bought an etec the same year our neighbor at the lake bought his merc four stroke and the dealer has already done 7 grand worth of work on his merc. Yes it was covered under warranty but a motor that's 3 years old and dealer maintained is pretty bad. There are more etecs in our tournament series then other brands combined!!
was just the fuel pump in the end
etec owners group DOT com I'm considering buying a boat with a 2011 250HO Etec hanging off the back..... I'm getting scared.....
@Al Yaz I haven't found that to be the case. I've got a 2017 150 that spends more time in the shop than in the water. Not very happy with it.