วีดีโอ

The pro micro is small and can fit in the bottom of the shifter. But the two usb boards works.

Did you used the right Arduino sketch? Have you photos of your wiring?

Can you send me a mail ? The address: diysimstudio@yahoo.com

@@diysimstudio8225 Sent

You can use the 5 speeds plate, please see the video at the end.

Hello, thanks for your post, but actually I'm not interested by your Idea.

You can buy the cad files, the link is in the description of the video.

Hello, I don't recommend a load cell weight under 100kg. Don't worry, the calibration can be set in the setup of your game. The informations about the load cell compatibility is indicated here : www.diysimstudio.com/produit/diy-sim-racing-pedal/ in the "PARTS COMPATIBILITY" section. Best regards, DIY SIM STUDIO

@@diysimstudio8225 Thank you very much, I hadn't noticed that part, my lack of attention

@@tiago.32g50 You're welcome. 😊

Hello, The Arduino sketch works only with Arduino pro micro or Arduino Leonardo board. Arduino Uno board can't work with the Joystick library. Best regards, DIY SIM STUDIO

With USB plug, you can use Arduino or Leobodnar board.

Hi, Between 80€ and 150€.

Hello, I think the mobile part should be printed on the side.

​@@diysimstudio8225 the side of the mobile part a small round section that protrudes out which would then need a lot of supports

Is there a version of the mobile part for 3d printing where you just use washers instead?

@@afkafkafk There is not mobile part without sides washer, sorry.

@@diysimstudio8225 What about Production -> Optional 3D printed Parts -> Alternative Massive Mobile Part?

The web site work perfectly, I don't understand your comment.

It's the part at 1:08

The Leobodnar is a little more accurate for the brake and more easy for the soldering, and all Arduino micro and Leonardo boards with Atmega32u4 will work.

Hello, I never printed the parts, I paid 3D printing services to do it. I recommend you to ask help on 3D print forum. Best regards, DIY SIM STUDIO

Hello, I can't give you the solution because the throttle and clutch was designed for potentiometer. Best regards, DIY SIM STUDIO

@@diysimstudio8225 Would it work if I just made 3 brakes and put springs instead of those rubbers?

@@leonardosakamoto1290 I think it will work, because bushing are like spring, but I didn't tested so I can't confirm.

Arduino (pro micro or Leonardo) and Leobodnar

Hello, thanks. The software is Diview.

Hello, I didn't sell this product. Best regards.

I sell the Cad files here : www.diysimstudio.com/produit/diy-sim-racing-pedal/

Hello, if you put washer or any 3D printed part that compress the spring, it will increase the strength of the lever.

@@diysimstudio8225 Hello, another question: how many grams of filament do you need to make the shifter?

@@alexrodriguezvega357 Hello, I can't give you an answer sorry, but it will not cost you lot of money don't worry, the shifter was designed to be printed without waste of materials.

It works on PC only with USB Board like Arduino or Leobodnar. It will be recognized as a joystick.

Hello, if you use Arduino, you will set your buttons directly on your game, in the same way you set another add-on (button plate, button box, etc)

It's not hard to mount this shifter on a desk.

@@diysimstudio8225 ok but how?😅

@@TobiMrPivotJocham you can mount it on a support with holes, and fix the support with clamp on the desk. It avoid to make holes on the desk.

Thanks you !

Hello, the sketch is included in the file of the two pedals (3D printed and stainless steel) you must download it to get it, I can't give you the sketch, sorry.

ok@@diysimstudio8225

Hi, No, you don't need the Arduino part with Leobodbar.

Hi, I don't tested the pedal with SIM Hub. Did you used Arduino board or Leobodbar ?

@@diysimstudio8225 Arduino micro

They are included in the file.

Thanks 👍

Thanks you. The link is in the description, in the page of the handbrake

Thanks 👍

Thanks 👍

Hi, the list is available on the page of the pedal in the bottom. 😉

@@diysimstudio8225 ty

Hi, thanks you. The handbrake has an loadcell connected on a Arduino board, these boards aren't compatible with console, they work only on PC.

Is there a way to make it work with console?

@@silvamario350 I don't know, the handbrake was built for PC only, because Arduino and the loadcell works only on PC.

Merci beaucoup 😉

Hi, I can't give you an answer because the pedal was designed to be used with potentiometer.

The value can be changed in the brake setting in Arduino sketch file.

Thanks 👍 I never tried, but I think it's not possible.

@@diysimstudio8225 It's cool to make a bolub like that, I would buy it with this option from you))

I like to do it myself) but I'm not strong in electronics)

I can't give you an answer, sorry. The pedal is only compatible with 4 wire load cell.

@DIY Sim Studio well I purchased some pro Micro boards and hx711. I guess I will try and find out. Just missing the green wire from load cell. I guess these are referred to as half-bridge strain gauge load cells.

Hi Steve, thanks for your purchase. 😉The recommanded material and infill is indicated in the name of the .Stl file. The Pla or Abs is recommended. The 3D printed pedal files are in the folder Production > 3D Printed Edition

@@diysimstudio8225 Ok. Mine has infill at 100% where recommended but nothing for parts that don't require 100% infill. None of mine have any mention of material, though you've given me that info so I'm good there. I'm getting crazy quotes for 3d printing these so if I go that route I might just buy a 3d printer and do it myself. I've been looking for a reason to get one! Thank you.

@@stacarter if the infill is not indicated, then you can use the infill you want, the minimum is 20%

im here with that as well allthough not for this particular project :) I wanted to make myself a racing wheel and shifters for sim. Bought a Creality ender 3 last month and I'm having a blast doing everything :))) all for under 100 euros :D + materials another 20 or so @@stacarter

Hello José. Sorry for the delay of the answer, I just read your message. Yes the Arduino (and Leobodnar) boards works with all simulator on PC. And the brake can be adjusted in the Arduino code and the game setup.

@@diysimstudio8225 thanks

Hi, thanks you. No you can't use hall sensor

The Arduino Sketch is included in the pedal file.

#include <HX711.h> #include <Joystick.h> HX711 scale(0, 1); Joystick_ Joystick; void setup() { pinMode(4, INPUT_PULLUP); // Button Pins set to input with pull up risistors pinMode(5, INPUT_PULLUP); pinMode(6, INPUT_PULLUP); pinMode(7, INPUT_PULLUP); pinMode(8, INPUT_PULLUP); pinMode(9, INPUT_PULLUP); pinMode(10, INPUT_PULLUP); pinMode(16, INPUT_PULLUP); pinMode(14, INPUT_PULLUP); pinMode(15, INPUT_PULLUP); pinMode(18, INPUT_PULLUP); pinMode(19, INPUT_PULLUP); pinMode(A2, INPUT); // set potentiometer pins to input pinMode(A3, INPUT); scale.set_scale(-10000); Joystick.begin(); } void loop() { Joystick.setButton(0, !digitalRead(4)); // turn on button if pin is connected to ground Joystick.setButton(1, !digitalRead(5)); Joystick.setButton(2, !digitalRead(6)); Joystick.setButton(3, !digitalRead(7)); Joystick.setButton(4, !digitalRead(8)); Joystick.setButton(5, !digitalRead(9)); Joystick.setButton(6, !digitalRead(10)); Joystick.setButton(7, !digitalRead(16)); Joystick.setButton(8, !digitalRead(14)); Joystick.setButton(9, !digitalRead(15)); Joystick.setButton(10, !digitalRead(18)); Joystick.setButton(11, !digitalRead(19)); Joystick.setXAxis(analogRead(A2)); // analog read potentiometer 1 set x axis Joystick.setYAxis(analogRead(A3)); // analog read potentiometer 1 set y axis Joystick.setZAxis(abs(scale.get_units(1))); // read load cell set z axis }

@@irfannugraha7090 throws an error, no matching function for call to hx711 any idea?

No it won't work

Thanks 👍

Loadcell for the brake pedal, potentiometer for the throttle and the clutch.