วีดีโอ

Great video,love the content and music!

The V8 Cat 3408 engine was built by God!

Nice setup! How to get rtk fix from your com 5 port? Got a f9p and wondering how to get the gps signal and the correction to opengrade

Hi, do you have a schematic of your PCB or maybe a link to a forum thread? I've built a simple bang bang relay one but would like this too. Thanks

Great video.

This had nothing to do with track frame bogey pins.

Очень много техники ,я на таком внутреннее заднее один менял

I see you're in DGPS, don't you have rtk? Could you put a video of the wheel angle sensor and the steering valve? I have a JD 8000 series and I'm thinking of adding a hydraulic valve for AgOpenGPS. I currently have two CASE tractors running on AOG, one with an electric flywheel motor and one with OEM hydraulic valves. Nice tractor and seeder!

Fantastic video clip 👌 looking in from Ireland 🇮🇪

What size are those fabric barns

So inspirational!!! Do not waste another day - Promo'SM !!!

NICE PLANTER!!! I see you are a no-tiller. If you ever think you need more down force I have designed a bolt-on kit that converts the ol' cyclos to pneumatic ILO the steel springs as well. I have a couple videos of it on my channel. Makes about 525 pounds of force at 100 psi. I typically only need 50 psi to plant into heavy clay. LOve your row shut offs. So awesome to watch them work. Looks like it is tied into GPS? or are you flippin switches????

Use it to rip the clay before loading easier on quads tracks

Cool vid To much track slip loading why do you guys not rip it a little for easier loading .?

love it! Cheers!

Hi guys, I neat trick with the skidsteer can assist you loads in refitting these tracks, what you need is a 2 foot length of decent wall thickness box section that slides neatly over one of the forks with a hole in the top and a 2omm nut welded on so bolt can be screwed in so as to clamp the box to the fork, at the opposite end 6 inches in weld a piece of thick angle like 60x80x10mm across the box and weld brace fillets behind, then you can lift the track on the top drive roller and push on the side of the track with out risk of puncturing or slipping of the track, happy track fitting guys

Ich absolvierte eine vierjährige Ausbildung als Baumaschinenmechaniker. Mein Motto war: „Wenn du die Reparatur im Urwald kannst, dann kannst du es überall“. Dort hast du nicht alles Werkzeug aber mit Wissen und Erfahrung kannst viel erreich. Dies geht nur mit unkonventionellen Methoden. Beispiel: Kran um die Hydraulikpumpe auszubauen. Unter einen starken Baum fahren. Ein langes Holz unter den Dicken Ast schnüren. So kannst du mit dem Hebelgesetz des Holz die Pumpe leicht heben. Mit einem langen Holz und Hebelgesetz kannst du viel bewirken. Ich bevorzuge Heutzutage trotzdem eine geheizte Halle und fester Boden mit allem Schnickschnack.

It's good to know I'm bit the only one with worn tires on my skid steer.

myslałem ze kapcia złapli a tu na nowe wymiana

How do you compensate for all that topsoil you push off to build the terraces?

synergétique

So what was wrong with the tracks? Lugs ripped off?

Wish that I had recorded some of the ones I had to change out. Only did Cat Challenger but it was in the beginning, had one with all of the three point and PTO on the back wad the track up under the machine on about a 40 degree slope. Had to tie it off to a 615 at the top of the hill to keep it from slipping off of the jacks. It was a lovely all night job.

mechanik kurwa,szpilki na ziemie polozyl

Great.

Boa noite, trocar a lagarta do steyger , mais fácil do que trocar um pneu. Muito bom trabalho de vocês. Sou Aqui do Sul do Brasil, estado do Paraná. Que Deus os abençoe 🖐️

By the way, why didn`t you unscrew bolts with Milwaukee? With 2000nm model you could make new threads for these bolts :D

How many hours does these tracks last?

Drove a quadtrac in the uk for 5 years got through 2 sets of tracks the lugs in the center ripped off.

The young man in the video sure seems to be a hard worker. Must be nice to find such good employees at this time, hope he’s getting paid well!!