- 6
- 11 264
Tomáš Břinčil
เข้าร่วมเมื่อ 13 ธ.ค. 2011
วีดีโอ
Es'hail 2 / QO-100 DVB-S2 beacon stream from radioamateur transponder
มุมมอง 1885 ปีที่แล้ว
This is simple tutorial how to set up necessary equipment for recieving radioamateur beacon broadcasting DVB-S2 on Es'hail 2 / Q0-100 satellite. 1) Set up LNB convertor, use T bias tee with 16 V for horizontal polarization, aim dish to 26° East, wire to RTL* dongle. 2) Install rtl_sdr package. 3) Follow instructions on www.pabr.org/radio/leandvb/leandvb.en.html 4) Play recieved signal in VLC: r...
can you re-up up the files please, it is gone . please re-upload
what is the circular wire for?
Anybody here still have the stl? And do you mind sharing?
What is the address of that websdr?
Добрый день! Дорогой Томасбринсил, молодец! Мне очень понравился дизайн антенны. Не могли бы вы поподробнее выложить файлы для 3д печати, а то не удобно запускать принтер на 14 часов. Спасибо за хорошую работу. 73!
goot lern.😌tenks.
Good time of day to you! I have seen your project of Satcom antenna, all the comments and the blog itself. It has been really helpful, yet i haven’t found answers for some questions. 1. What material did you use for the antenna itself? 2. What kind of cable did you use to connect the lower part of the antenna? 3. Were you able to make director, the antenna amplifier, if I understand it correctly? Since I’ve seen something that looks like the interface for it on the last 3D printed part of antenna? 4. Do you have a file or something to see how you connected it all, if it would be unclear from previous answers. Both for antenna and director-amplifiers?
Hello, do not tell me what SWR this antenna has and how it has RX / TX on Satcom?
I dont!
Ahoj parádní věc mohl by ses mi ozvat na e-mail ?
Ahoj Vite, odkazoval jsem tady muj blog, jestli mas otazky ohledne anteny, napis tam :)))
@@tomasbrincil6448 byl bych spíše rád za soukromou konverzaci třeba skrz Fb nebo e-mail jestli je to možné
Effortlessly beautiful bird. Hats off to the pilot, compliments!!
А где файлы для печати? Где размеры антенны?
Need to print a thicker cowling , looks great , printed on at 1325mm size
Do you have a material and measurement list?
All information in the comments.
Willing to sell these? Ha
The shipping will cost more than material.
@@tomasbrincil6448 I would still be willing to pay for 2 of them possibly. If it is something you are up for doing.
@@tomasbrincil6448 if you are willing i would be interested in 3 of them. I'll pay material and shipping. That is no problem
@@XtreamMotoX sorry I am not in the situation to spent my time doing these antennas.
Ahoj, můžu se prosím zeptat, jestli se anténovej kabel pájí jenom k té vrchní růžici se 4 listy? a spodní základní patro je jen smontované, bez dotyku anténího kabelu? nebo se musí připájet na obě patra?
Nychrom Ahoj, zalezi jakou chces polarizaci. Pokud Ti staci linearni, tak pripoj jen dva zarice, pokud chces kruhovou, tak pripoj oba pary, ale musis vyresit fazovy posuv o 90° A to spodni patro plni funkci reflektoru. Napis mi na me@tomasbrincil nejaky detaily, poradim Ti.
Great to see it flown in a scale like manner, will be maidening mine tomorrow and hope she flies as well as yours. Did notice the engine surround is kinda delicate and was thinking of playing with the Cura settings to strengthen it up a bit and reprint, would you recommend this?
Great looking plane and super flight! I just started printing this plane. Did you use 3DlabPrint recommendation for CG? Any balancing issues? Can I ask what motor and battery you are using? Thanks again for sharing.
Hi! What a great looking and flying plane. Is this the LW-PLA/PLA hybrid version? What motor do you use?
Can you share 3d models for parts of this antenna?
blog.tomasbrincil.cz/?p=269
@@tomasbrincil6448 thank you so much, dude!
nice flying! Is that 3s or 4s?
Thanks man! Dad is flying 3S 1300 mAh + 70g balast to get right position of center of gravity. These airplanes are designed in 3DLabPrint by guys flying ACES combat competiotion and they fast as hell. For easy and much slower flying you are fine with half power equipment.
@@tomasbrincil6448 Thanks mate 👍 I've got my TA152 setup with the Emax 3510 MT on 6S 1800mAh and I also have to put the 6s battery far in front to get the center of gravity right. Have good time and take care
Hi! Good work! Can you share 3d models for parts of this antenna?
blog.tomasbrincil.cz/?p=269
@@tomasbrincil6448 thanks! I was have own designed for it. But how to connect cross vibraters on fider?
@@whalekiller2444 great! Antenna is yagi uda type- dipole with reflector. Cross parts are not connected. The polarization is linear not circulal.
@@tomasbrincil6448 the link doesn't work anymore. Do you have the stl files hosted anywhere else?
Chlapi, co v tom mate za elektroniku a za motor... Díky..
Ahoj, jelikož to byl první tištěný model, je tam vše co doporučuje návod. Ale letělo by to možná i s polovičním výkonem. Je to dost přemotorovaný a většina těch průletů byla sotva na 1/2 plynu.
Looks like it flies really well, how many print hours and filament it took?
I don't know about this guy's IL-2, but I can say that mine took less than a roll (<1kg) to print. I'd plan on 5-7 days of printing. I work Monday through Friday so maybe it took me longer.