วีดีโอ

Thank you so much for the info. I was just getting ready to order a used mirror from a junk yard. You saved me $200

My 2010 Lexus IS 250C driver side mirror just developed the same problem. After seeing this video, I was hopeful of fixing it but couldn't as in my case the shaft is not like Larry's - there is just a very minor protrusion unlike the very pronounced one in Larry's video, so no way the washer would hold if the spring was pushed down. As others have noted, the spring is very strong and difficult to compress even with the use of a ladder, rubber mallet+monkey wrench. I may have to live with the double-sided tape fix as I don't feel like paying Lexus $1005 for the mirror assembly + $326 labor + tax for a flaw which shouldn't have been there in the first place!

Rear are easy to remove and install show how to remove and install the fronts? They seem more of a pian in the ass

Did you get the battery on Amazon as well? And can you give us the link please. Nice video man. Is hard to find any content about this sxs

thanks a lot i was upset someone hit my car and broke ....i will try the way you did ..

Do you happen to have any of these left for sale?

Now if you don't want that retainer washer to come out again. What l did it was a hole thru the pole, and l pushed thru that hole a wire. I used a paper clip. That will stop the retainer from popping out every time. Guaranteed.

Thank you it was too easy ! I had a O2 sensor socket with an extension and a mallet dead blow, went on, no ladder or pipe wrench. Tip: I used a plastic 55 gallon trash turned up in side down with a terry cloth towel to catch any dropped screws and supports the loose mirror and holds the tools!🛠️

Tip: Use a O2 sensor socket, and tap it on with a mallet. Worked like a charm!! Thanks for the video!! Also, it seems you do NOT have to remove the screw on the lower inboard. The back comes off with that still screwed in and you can access the snap ring and spring.

8.5 minutes of my life I'll never get back. You need to change the title of this video to anything BUT secondary battery install! SMH

I took a PVC Tee and cut a grove for the wires. It was easy to apply pressure by hand to get the initial catch. For the final whack with a mallet, I used a flare wrench. All took less than 10 minutes.

Just applied the fix exactly as instructed. Worked like a champ! Thanks for the helpful video!

Larry = "the man". Such a quick fix. Saved me frustration, time and money. Thanks Larry!!

I can easily splice 2 speakers into one module, right? Does the module need to be in line for the remote? Can I hide it?

Sold my Rmax and bought the KRX the Rmax is a great machine but the KRX rides a lot smoother Ilove it

Thank you for the video. This happened to my 2010 es350 a few days ago and I didn’t bother going to the dealership but went straight to TH-cam and found this video. I needed the assistance of my cousin to hammer down the monkey wrench while I applied the pressure. Problem solved!!!

How does it lift and support the that KRX?

No way! This worked great! And I am not handy. Follow every step. Amazing. I almost skipped the Vaseline. Worked perfectly!!

Thank you really much for the help it’s so appreciated 🙏

what windshield is that?

What amplifier do you use?

@ 6:06 Sealed box are better also use marine speakers with stitching becuse your subs are glued together and as far as amps use sound stream motorcycle amps they put out almost 1000w for the 4 ch amps and subs you can get them marine grade but what I do is open my amps hot glue any hole through components for vibration proof A MUST for any UTVs and then i use Humi seal to water proof the electronics

Thanks! I live in TX and have wanted to get one!

Yes, in Texas, you can take your vin number and spend $25 and get a tag. It will allow you to drive your machine within 2 miles of your house and on roads that are posted 35 mph or less

Is that a street legal Texas license plate or just an off road type tag?

This is the video I was looking for because it is the exact issue I am facing with my side mirror.

Thanks bro

Never seen such a mess of wiring as that

What new skidplate did you go with and how has it held up?

Hi, nice video. Just curious if those 33inch tires you have on the pro xp rubbed any? I see you have the stock a arms. I was thinking about going with a 33inch tires on my pro xp. Thanks

Can the signal lights be LED?

Brilliant. Worked perfect! Mine however had a different issue. I have never seen anything like it. All 4 screws that house that clip, that piece somehow unscrewed itself. I can see the screws inside but it’s too tight to reach

This is awesome!! Thank you soooo much!!!!

This was the second video that I watched. It was more thorough and the second try I put pressure on using the ladder. I did buy an oxygen sensor socket for sixteen dollars which was a more direct hit on the washer. While crimping the teeth on the washer, I inadvertently cut one of the yellow wires which I later soldered back together and insulated with tape. Hit the mallet once and the washer seated, then put everything back together and the mirror works great, a great sense of relief since the dealer may have wanted to replace the whole mirror for $1100.00. So grateful for your help!

I cannot thank you enough for this video sir, God bless you 🙏🏻. I was so upset earlier, got the part fixed! Thank you!!!!

1:57 Why did you just let the part fall on the ground like that? I would not want you working on my car.

Thanks ❤

I paid a small fortune to have the passenger side fixed at Lexus a couple years ago. I just did the driver's side. Hope it holds! Thanks!!

I tried this but couldnt get to work, looks like the spring clip could be to wide open, or the metal piece im pushing it down in is stripped and wont the clip wont grab it.

Dude you the man. Some of the best Info I've seen on a side by side video

I'm looking for a relay . Can you suggest somewhere to buy one?

How do i compress the spring

I feel like this video is more about the tools and parts you need than the how to. Good but I had to skip through to get to the parts the video was titled. A little inconvenient but ok.

Thank you so much for this video !!!

My SC 300 mirror was repaired twice before, and the tube was mangled. What I did was put a long thin bolt down the center of the tube (with a small washer on top), right next to the wires. On the bottom of the support, I put a washer and nut to tighten the spring down. I used a weaker spring. This will never fail again!!!!

What year is your Polaris I have a 2022 Polaris Pro XP 4 will this work on mine?

OMFG THIS WORKED LOL didn't have mallet but it was done. THANKS!!!

where did you get the wire with the built in receiver?

Cam Am pissing oil all over the trailer..KRX dry as a bone..Checks out..