วีดีโอ

Great harness and wing. I love mine so much

First, great video - thank you for that! Silly question here: when attaching the weight pocket per your video instructions, having the nut on the inside (against my back) is pocking and uncomfortable. When I reverse the screw (nut against bladder) and point the flat screw against my rip it gets more comfortable as flatter but then the nut obviously faces/points towards the bladder. Unless the bladder is fully inflated, I could not see this being an integrity issue for the bladder itself through wear and tear / friction over time. Worst case, of course, a puncture of the bladder (more important than my comfort). Question though is, can the nut be reversed in not pointing/pocking into my back and do you foresee any issue going that route for the benefit of comfort? Thanks!

How do you instal the hose protector?

Oh no!!! Thank you for keeping us updated

What do you think about putting an O ring in the bolt snap to provide a break away ?

Nice Ending

Thank you Tim for educating us

Thanks!

Hello, I have a question about whether it is worth buying the Atomic M1 or B2 in 2025. I am interested in this brand but I am not sure which model to choose, M1 or B2, so that I can dive in cold waters below

This was super helpful. I was struggling with how to get it pulled apart. It had been serviced, but they left it rotated in a weird direction. It’s always the answer was I just wasn’t using enough force

Thank for the video, is it important to install a anti-friction washer ?

Put a small rubber tube through wrist area to stop the squeeze when coming up.

GREAT VIDEO, Tim!!!! In addition, I learned the following tips from Jill Heinerth's You Tube video "How To Select Easy Inexpensive Dry Gloves for Scuba Divers" in which she has a great tip that I use for donning and doffing these inexpensive pullover gloves!!!!! I use a PVC pipe that I purchased at Home Depot that couples right over my drysuit's permanent suit cuff. Then, the "pre-loaded" glove (gloves fingers loaded through the PVC and the glove's cuff folded back over the PVC coupling) can EASILY be pulled [BY ME!!!] (i.e., self-donning!) over the suit's wrist cuff ... and ***VOILA!!*** you're ready to dive!!!! P.S. The other tip I've discovered is that when diving with dry suit gloves, I recommend using Bolt Snaps that feature "Big Grip" tabs to manipulate the snap's gate plunger/closure!!! The rounded teardrop-shaped [low profile] "tabs" are better suited for use when diving in warm/temperate water in which you're using either NO wetsuit gloves or thin (3 - 5 mm) wetsuit gloves! Appreciate Your Thoughts in a Reply. Morgan

One system you didn't mention is the seal-on-seal variant, were you buy dry gloves with a seal on them, which you just place on top of the latex seal from your suite. This is somewhat tricky and requires some practice, just as with pull over gloves, but with practice you can do it in 30s. You first put on your glove liners, then the dry suit to use the glove lines as the spacer between the suit seal and your arm for warmth and equalisation of the glove. I ran this for many many years, and this is the least bulky system you can ever have. No rings, no hard parts. When I started doing longer and colder dives, 2h+ and 4c, this became to cold due to the fact that you only have a compressed glove liner and two layers of latex between your arm and the surrounding water. Even if you size your latex cuffs correctly, it will slightly reduce the blodflow to your hands. That's why I've moved to using the quck-cuff system, and I'm mounting my latex gloves directly in the "cuff" ring. This means no seal, and no compressed undergarments and this is what I need to do 2h+ dives in 4c without electric heating in the gloves. I just love having the gloves directly on the suite without any moving parts and orings that can leak.

How do you mount the canister light with the weight pockets attached?

What's the cave ring for?

I don't understand how the rail attaches

I talked with Dion at DUI and she said by no means use any silicone on the zip seals it will cause it to deteriorate quickly. So FYI, great video but as I said silicone is a no-no according to Dion who works on repair at DUI said do not in fact she told me if I used any to quickly take soapy water And scrub them clean so I did

I told them I was using gear aid. They still said not to use it. They said clean it right away with soapy water. So I did. I only use it on one dry glove. I’m glad I call to check. I just had it retrofitted last fall with zip seals.

Oh, the repair dep was DUI in Calf.

FYI I just talked to the repair department and they informed me …do not use any silicone spray or any product that has silicone. It will destroy the zip seal rings and zip seals. Only use soapy water is there recommendation. Saying all that. Great video.

What company made the the new hose and thanks

Thanks, great insight. What prevents the sitech system from being installed on a DUI drysuit, as an aftermarket mod?

Is there a requirement to reduce the gas inlet pressure or can you cascade into the target cylinder and then boost to a final desired pressure. My oxygen and Helium come in cylinders that are usually around 2500psi and I would rather not have to reduce that down prior to boosting. Thanks

I hate you, you don't "just" snap it into place!!! Haha I'm sweating over here!

What happened to the sound??

Thanks for video. Hopefully don't have to do this for a long time with my new one

Silliest thing I've ever seen...just attach the weights directly to the BCD waist-strap and/or cam-bands!

Thank you for the great video. Is it possible to chenge the cable as it does not work anymore? Where can i Buy the cable?

Very helpful, thanks.

Great video but I really don’t understand what the point of a wing is if you add weight pockets. If you add them you essentially just have a BCD with a lot of extra steps.

Great video Tim, and very well filmed. I am actually thinking of removing the weight pockets as I don't use them on my Ghost -- I use trim weight pockets on the tank band instead. To remove them, do I just reverse your process? Also, I would like to keep the D-ring attached to the left weight pocket. Is the ring and triglide removable from the weight pocket?

Holy crap the soap and water trick was a game changer. Also with the folding the seals inwards and having them fold back out into the slot. Thank you!

ultima is best.

Only one missing : rolock system

Nice video, what fitting have you used for your air drive connection to the G1/2’’ inlet port? The one I have supplied from USUN leaks badly. Thanks!

thank you kermit the frog

You've got the flock lining facing outside. Isn't there a (small) risk of seepage that way?

What are your thoughts on the pockets after use.

Could the Santi Smart Seal work with the DUI Wrist Seal if you did not want to use their Zip Gloves?

great info. Glad to subscribe

Por gentileza! Consigo comprimir gas hidrogênio de ate 350bar?

about 50 sek in... the suit ring and the suit side ring.. is that just in like that? no need for glue or somting?

Is the pocket with the D ring mounted on the right or left? and what does it involve? Thank you

Interesting to see the various options. I've only experienced the Santi Smart Gloves system but it's kept me dry for years now. Been very nice. Have used it with various types of gloves. Marigold, Showa 720, Santi heavy duty, etc. The Showa are cloth lined so require a different method to seal, but there's a good video on YT that shows how.

How well would the ChOptima attach to this? The excess webbing in the front and shoulder pads leave me a bit concerned.

What are your thoughts on the psi system. Thinking about ordering an Argonaut 3.0 and was looking at the ultima or PSI system. This is my first time getting into a trilam suit. So lots of research going on. Cheers.

That's why I buy my stuff from Tim

What is the Velcro strap used for on the gloves?

I have the fourth element dry suit already, can I use other dry gloves system? Such as kubi or santi?